If any components of this unit are broken,
ATTENTION
do not operate properly, or for product returns,
please contact Pragotrade Inc. at
1-800-814-4895
Outside the U.S. call 440-638-3131.
For the online catalog, log onto www.westonsupply.com.
Exclusively imported by Pragotrade Inc. Strongsville, Ohio
www.pragotrade.com
MODEL #01-0103-W
REV 05/03/07
MANUAL CUBER/JERKY SLICER
MOTOR ATTACHMENT
INSTRUCTIONS
6
5
Thank you for purchasing a Weston Brand Manual
Cuber/Jerky Slicer Motor, we are sure that you will be
pleased with your purchase.
Proper cleaning and maintenance will help ensure
that your appliance will continue to perform at its best.
Clean and Dry all parts thoroughly before storing.
Even though your Weston Brand Manual Cuber/Jerky
Slicer Motor is primarily Stainless Steel, you should
spray the metal parts with lubricant prior to storage to
prevent oxidation.
MODEL #01-0103-W
3
WARRANTY INFORMATION
SAVE THIS WARRANTY INFORMATION FOR YOUR RECORDS!
Pragotrade Inc. warrants to the ORIGINAL RETAIL PURCHASER of this product that if operated in accordance
with the printed instruction accompanying it, then for a period of 1 year from the date of purchase, the product shall be
free from defects in material and workmanship.
The Warranty Card, along with a copy of the original receipt, must be received by Pragotrade Inc. within 30 days from
purchase date for the warranty to apply. Failure to send the completely lled out Warranty Card, along with a copy of
the original receipt, will void the warranty.
The product must be delivered to or shipped freight prepaid to Pragotrade Inc. for warranty services, in either its
original packaging or similar packaging affording an equal degree of protection. Damage due to shipping is not the
responsibility of the company. Pragotrade Inc. charges a $35.00 per hour bench charge. NOTE: No repairs will be
started without the authorization of the customer. The return shipping cost to the customer will be added to the repair
invoice.
Pragotrade Inc. will repair (or at its discretion, replace) the product free of charge, if in the judgment of the company,
it has been proven to be defective as to seller’s labor and material, within the warranty period.
New or rebuilt replacements for factory defective parts will be supplied for one (1) year from the date of purchase.
Replacement parts are warranted for the remainder of the original warranty period.
For non-warranty repairs, contact Pragotrade’s Customer Service at 1-800-814-4895 M-F 8am-5pm EST (outside of
the United States 440-638-3131) to obtain a Return Authorization Number (RMA Number). Pragotrade will refuse all
returns that do not contain this number. DO NOT RETURN THE UNIT WITHOUT PROPER AUTHORIZATION
FROM PRAGOTRADE USA, INC.
LIMITATIONS: The warranty is void if the product is used for any purpose other than which it is designed. The
product must not have been previously altered, repaired, or serviced by anyone else other than Pragotrade Inc. If
applicable, the serial number must not have been altered or removed. The product must not have been subjected to
accident in transit or while in the customer’s possession, misused, abused, or operated contrary to the instructions
contained in the instruction manual. This includes failure caused by neglect of reasonable and necessary maintenance,
improper line voltage and acts of nature. This warranty is not transferable and applies only to U.S. and Canadian
sales.
Except to the extent prohibited by applicable law, no other warranties whether expressed or implied, including
warranty merchantability and tness for a particular purpose, shall apply to this product. Under no circumstances shall
Pragotrade Inc. be liable for consequential damages sustained in connection with said product and Pragotrade Inc.
neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than
such as is expressly set forth herein. Any applicable implied warranties are also limited to the one (1) year period of
the limited warranty.
This warranty covers only the product and its specic parts, not the food or other products processed in it.
CUT ALONG THE DOTTED LINE AND SEND THE WARRANTY CARD ALONG WITH A
COPY OF YOUR ORIGINAL PURCHASE RECEIPT TO:
20365 Progress Drive, Strongsville, OH 44149
Pragotrade Inc.
-2-
WARRANTY CARD
SEND THIS CARD ALONG WITH A COPY OF YOUR ORIGINAL PURCHASE RECEIPT
Customer Name: ________________________________
Address: ______________________________________
City/State/Zip: ___________________________________
Telephone Number: (_________) ___________________
E-Mail Address: ___________________________________
Original Date of Purchase: _______/_________/__________
Product Model #: __________________________________
Serial # (if applicable): ____________________________
-7-
9. Install the Bracket Arm onto the two 110mm Hex
Head Bolts. Screw the two Wing Nuts onto the bolts
and tighten until the Motor is secured in place.
Figure 7
Note: DO NOT over tighten the Wing Nuts, tighten
only enough to secure the motor in place. If the Wing
Nuts are to tight, the Motor may bind during use.
Wing Nut
Bracket
Arm
Figure 7
10. The unit is now fully assembled and ready for use. Be sure to read and
understand the instructions that came with your cuber/jerky slicer for safe
operation.
1
5
7
4
3
6
2
8
Fully assembled Motor
-6-
COMPONENT LIST
DIAGRAM NUMBER PART DESCRIPTION PART #
1 Motor Bracket 01-0104
2 Adapter 01-0105
3 Bracket Arm 01-0106
4 MG Wing Nut (2) 01-0107
5 110mm Hex Head Bolt (2) 01-0108
6 16mm Allen Head Bolt (2) 01-0109
7 Motor 01-0101
8 Allen Wrench 01-0111
If any components of this unit are broken or the unit does not operate
properly, call Pragotrade Inc. Toll Free at
1-800-814-4895
Monday thru Friday 8:00am-5:00pm EST.
Outside the U.S. call 440-638-3131
-3-
GENERAL SAFETY RULES
ASSEMBLY INSTRUCTIONS
READ AND FULLY UNDERSTAND ALL INSTRUCTIONS
AND WARNINGS PRIOR TO USING THIS PRODUCT.
YOUR SAFETY IS MOST IMPORTANT: FAILURE TO
COMPLY WITH PROCEDURES AND SAFE GUARDS
WARNING!
MAY RESULT IN SERIOUS INJURY OR PROPERTY
DAMAGE. REMEMBER: YOUR PERSONAL
SAFETY IS YOUR RESPONSIBILITY!
1. ALWAYS DISCONNECT product from
power source before servicing or cleaning the
unit.
2. KEEP FINGERS CLEAR of the cutting
blades at all times. Failure to keep ngers
clear of the cutting blades may result in
personal injury.
3. NEVER REACH INTO the top opening,
doing so could cause serious injury. Always
use the provided tongs.
4. KEEP CHILDREN AWAY. NEVER
LEAVE THE UNIT UNATTENDED. Be safe,
DISCONNECT from power source before
leaving the work area.
5. REDUCE RISK OF UNINTENTIONAL
STARTING. Make sure the power switch is
in the “OFF” position before attaching to the
power source. In the event of a power failure,
move the switch to the “OFF” position.
6. CHECK FOR DAMAGED PARTS. Before
using the Motor, check that all parts are
operating properly, and perform the intended
functions. Check for alignment of moving
parts, binding of moving parts, mounting
and any other conditions that may affect the
operation.
7. DO NOT USE the Motor if the power
cord is damaged. It MUST be replaced
before using the motor. Do not modify
the cord provided. DO NOT allow the
power cord to drape into your work area.
8. FOLLOW THE MANUFACTURERS
SAFETY INSTRUCTIONS on the cuber/jerky
slicer and the Motor.
9. TIE BACK loose hair and clothing, and roll
up long sleeves before operating the Motor.
REMOVE ties, rings, watches, bracelets, or
other jewelry before operating the Motor.
10. WEAR EYE PROTECTION. Wear safety
glasses. Everyday eye glasses are not safety
glasses. Safety glasses conform to ANSI
Z87.1 requirements. Note: approved safety
glasses have Z87 printed or stamped on
them.
11. Do not use the Motor while under the
inuence of drugs, alcohol or medications.
12. Do not overreach, keep proper footing and
balance at all times.
13. DO NOT FORCE THE UNIT. The cuber/
jerky slicer will do the job better and is safer at
the rate for which it was designed.
14. STAY ALERT! Watch what you are doing.
A moment of inattention while operating the
unit may result in serious personal injury.
1. Set up the manual cuber/jerky slicer per the instructions that came with the unit.
2 Remove the handle from the manual cuber/jerky slicer and set it aside. The handle
will not be used when the motor is attached.
3. Using the provided Allen Wrench, remove the two
socket head screws from the handle side of the
manual cuber/jerky slicer.
Figure 1
Socket
Head
Screws
Figure 1
4. Position the Motor Bracket so that the holes in the
bracket line up with the holes on the handle side of
Figure 2
Figure 2
the cuber/jerky slicer.
Motor
Bracket
5. Install the two provided 16mm Allen Head Bolts
through the Motor Bracket and into the cuber/jerky
slicerhousing.Besuretheboltsarermlytightened.
Figure 3
16mm
Allen Head
Bolts
Figure 3
6. Screw the Adapter into the cuber/jerky slicer. Figure 4
Adapter
Figure 4
7. Insert the Motor Shaft fully into the Adapter, allowing
the Motor to rest on the Motor Bracket.
Figure 5
Note: The Motor Shaft may need to be rotated for
proper alignment.
Adapter
Motor
Shaft
Figure 5
8. Slide the two 110mm Hex Head Bolts through the
holes in the Bracket.
Figure 6
Note: The threaded ends of the bolts should be
facing the Motor.
SAVE THESE INSTRUCTIONS!
Refer to them often and use them to instruct others.
Figure 6
110mm
Hex Head
Bolts
-5--4-
Loading...