To prevent personal injury or property damage, read and follow all instructions
and warnings.
When using electrical appliances, basic safety precautions should always be
followed including:
• Read all instructions, including these important safeguards and the care and use
instructions in this manual.
• Do not use appliance for other than intended use.
• Do not place on or near a hot gas or electric burner, in a heated oven, or in the
refrigerator or freezer.
• Do not operate when the appliance is not working properly or when it has been
damaged in any manner. For service information see warranty page.
• The use of accessory attachments not recommended by Focus Electrics may
cause injuries.
• Do not attempt to repair this appliance yourself.
To prevent burns or other personal injuries to children, read and follow all
instructions and warnings.
PRECAUTIONS FOR USE AROUND CHILDREN
• Always supervise children.
• Do not allow children to operate or be near the appliance, as the outside surfaces
are hot during use.
• Do not allow cord to hang over any edge where a child can reach it. Arrange
cord to avoid pulling, tripping or entanglement.
2
To prevent electrical shock, personal injury or property damage, read and
follow all instructions and warnings.
ELECTRICITY PRECAUTIONS
• To protect against electric shock, do not immerse cord, plugs, or other electric
parts in water or other liquids.
• Do not operate any appliance with a damaged cord or plug.
• Do not use this appliance outdoors.
• Always check to ensure handles/legs are assembled and fastened properly.
Over tightening can result in stripping of screws or cracking of handles/legs.
• Always attach plug to appliance first, then plug cord into the wall outlet. To
disconnect, turn any control to “OFF”, then remove plug from wall outlet.
• Always unplug from outlet when not in use and before cleaning. Allow to cool
before putting on or taking off parts and before cleaning.
• Your appliance has a short cord as a safety precaution to avoid pulling, tripping
or entanglement. Position the cord so that it does not hang over the edge of the
counter, table or other area or touch hot surfaces.
• While use of an extension cord is not recommended, if you must use one, make
sure the cord has the same or higher wattage rating as the griddle (wattage is
stamped on the underside of the plug protector). If the appliance is of the
grounded type, the extension cord should be a grounded-type 3-wire cord. To
avoid pulling, tripping or entanglement, position the extension cord so that it does
not hang over the edge of the counter, table or other area.
• Use an electrical outlet that accommodates the polarized plug on the appliance.
On a polarized plug, one blade of the plug is wider than the other. To reduce the
risk of electric shock, this plug is intended to fit into a polarized outlet only one
way. If the plug does not fit fully into the outlet or extension cord, reverse the
plug. If the plug still does not fit, contact a qualified electrician. Do not attempt to
modify the plug in any way.
• Do not use an outlet or extension cord if the plug fits loosely or if the outlet or
extension cord feels hot.
• Keep the cord away from hot parts of the appliance and hot surfaces during
operation.
• CAUTION: Risk of fire or electric shock. Only operate this appliance with the WB
#8 plug in place.
3
To prevent burns, personal injury or property damage, read and follow all
instructions and warnings.
HEAT PRECAUTIONS
• Do not touch hot surfaces. Use handles or knobs and hot pads or oven mitts.
• Extreme caution must be used when moving an appliance containing hot oil or
other hot liquids.
• Do not use temperature setting above 200°F (95°C) for buffet server or warming
applications.
• Do not place plastic cooking or serving containers or utensils directly on heating
surface as melting of plastic could occur.
SAVE THESE INSTRUCTIONS
USING YOUR BUFFET SERVER/GRIDDLE
Clear Cover
Food Pans
Food Pan
Holder
Temperature
Control
Grease Cup
BEFORE USING THE FIRST TIME:
1. Wash griddle, grease cup, food pans and clear cover(s) in warm soapy water
with a dishcloth or sponge to remove any manufacturing oils. Rinse thoroughly
and dry. Be sure temperature control socket is removed and socket is
completely dried. Slide grease cup securely in place below drain hole on g r iddle
surface. It is recommended that the grease cup be used with any cooking
application to help contain possible overflows or spills.
Griddle
4
2. Condition the non-stick finish by lightly wiping two teaspoons of cooking oil with
paper toweling or a soft cloth over the entire surface before turning on while
cool. Let cooking oil remain on the finish. Do not use butter or shortening to
condition the non-stick surface.
3. Check to ensure handles/legs are secured tightly to the griddle base. To
tighten, place cool griddle upside down on tabletop. Tighten handle/leg screws
by turning in a clockwise direction using the appropriate screwdriver. Do not
over tighten as stripping of the screws can occur. Periodic tightening may be
required.
USING AS A GRIDDLE
1. Always use on a dry, level, heat-resistant surface. Do not operate griddle when
hands are wet. Check to ensure handles/legs are secured tightly to the griddle
base. Attach temperature control to griddle with dial set to the OFF position. Be
sure grease cup is securely in place below drain hole on griddle surface. Do not
block airflow under griddle. Plug cord into a 120-volt AC electrical outlet ONLY.
2. Refer to the Temperature Guide in this booklet for selecting correct heat
settings. (If food is taken directly from freezer, use heat setting as indicated on
guide, but allow longer cooking time.) Most foods require a preheat period.
3. The signal light on the temperature control will go out when the cooking
temperature has been reached; add food. Heat may be increased or
decreased, depending upon personal preference and the type or amount of food
being prepared. The signal light will go on and off periodically to indicate that
the proper temperature is being maintained.
4. Foods may be prepared with or without fats. When frying, the use of a small
amount of butter, fat, or oil will improve the flavor, color, and crispness of foods.
When frying fatty foods such as bacon or sausage, excess grease will drain into
the grease cup through the drain hole located on the surface of the griddle. Do not remove the grease cup during cooking. Always allow griddle to cool
completely before removing grease cup.
5. Nylon, plastic, wooden, or rubber cooking tools are recommended for use on the
non-stick surface. Smooth-edged metal cooking tools may be used with care.
Do not use sharp-edged cooking tools such as forks, knives or food choppers as
scratching may occur. Minor scratching will affect only the appearance of the
finish; it will not harm its non-stick property.
6. When cooking period is completed, set the temperature control dial to WARM
for later serving, or set dial to OFF if food will be removed immediately from
griddle. After the dial is set to OFF, disconnect cord from wall outlet. Let griddle
cool before removing temperature control and grease cup.
5
USING AS A BUFFET SERVER
1. Always use on a dry, level, heat-resistant surface. Do not operate when hands
are wet. Check to ensure handles/legs are secured tightly to the griddle base.
Attach temperature control to griddle with dial set to the OFF position. Be sure
grease cup is securely in place below drain hole on griddle surface. Do not
block airflow under griddle. Plug cord into a 120-volt AC electrical outlet ONLY.
2. Place the food pan holder on the warming base and place food pans inside food
pan holder. Add food. Set covers on food pans. Note: Heat and moisture will
be retained if covers are kept on serving dishes. A slot in the cover is provided
for a serving utensil.
3. This Buffet Server is equipped with two heat settings. Setting 1 (warm) is a
minimum hold temperature of 140°F (60°C) and setting 2 (simmer) is from
180°F to 200°F (82°C - 95°C). For best results, use setting 2 to quickly reach
serving temperature, then adjust to setting 1 to keep warm. Check heat control
setting before operation. Do not use temperature settings above 200°F (95°C)
for buffet server or warming applications.
Note: You may use this unit either fully assembled with food pans or use the griddle
base alone as a warming tray. Food placed on warming base or in food pans
should be fully cooked and already hot as the Buffet Server is designed for
keep-warm function only. To retain heat and moisture in foods, kee p lid s on food
pans when not serving.
• A small amount of smoke and/or odor may occur upon heating due to the
release of manufacturing oils – this is normal.
• Some minor expansion/contraction sounds may occur during heating and
cooling – this is normal.
CLEANING YOUR BUFFET SERVER/GRIDDLE
1. Clean griddle thoroughly after each use. Do not immerse griddle in cold water
when it is hot. Let griddle cool completely, then remove temperature control and
grease cup. Dispose of grease. Immerse griddle and grease cup in warm
soapy water. The stainless steel pans and clear plastic covers may be cleaned
in a dishwasher. Covers should be placed in the top rack only. Wipe
temperature control with a damp cloth if necessary. Rinse and dry thoroughly.
2. Clean the non-stick surface of the griddle with warm soapy water, using a non-
metal cleansing pad such as Scrunge
Brite Cookware Scrub’n Sponge
®
scrubber sponge, Dobie®, or Scotch-
.
®
A dishcloth or sponge may give the non-stick
surface a clean look, but will not remove the tiny food particles that can settle in
the finish. Do not use metal scouring pads or harsh scouring powders.
6
3. Clean the non-coated aluminum underside of the griddle with warm soapy water
and a soap-filled steel wool scouring pad. Remove stains with household
cleanser. Remove burned-on grease with a special cleanser for appliances,
such as Wantz™Frypan and Grill Cleaner, Afta™Fry Pan Cleaner, Whink™Metal
Cleaner or SS-T
®
Metal Cleaner.
4. After washing, rinse griddle thoroughly with warm water and dry completely,
including temperature control socket area. Replace grease cup.
5. Your griddle and grease cup (with temperature control removed) may be
cleaned in an automatic dishwasher. Clean grease cup in top rack only. The
under side of the griddle will discolor due to the mineral in the water and the
high heat of the drying cycle. This will not affect the cooking ability of the
griddle. Each time that the griddle is cleaned in a dishwasher; the non-stick
surface should be reconditioned with cooking oil to ensure stick-free cooking.
Replace grease cup.
SPECIAL CARE:
1. A spotted white film may form on the non-stick surface. This is a buildup of
minerals from foods or water and is not a defect in the surface. To remove,
soak a soft cloth in lemon juice or vinegar and rub on the finish. Wash the nonstick surface thoroughly, rinse, and dry. Recondition the non-stick surface with
cooking oil.
2. The non-stick surface may also become stained from improper cleaning or
overheating. To remove stains, clean the non-stick surface by the following
method. Combine 1 cup of water and 1 tablespoon of ONE of the following
cleaners: Dip-It
®
coffee pot destainer, automatic dishwasher detergent, or dry
oxygen bleach crystals. USE ONLY ONE OF THE ABOVE CLEANERS; DO
NOT COMBINE. Make sure grease cup is in place. Preheat griddle to 225°F.
Wearing rubber gloves, dip sponge into water mixture and wipe over surface.
Continue cleaning procedure until mixture is gone. Turn griddle to OFF and
allow to cool. Remove temperature control and grease cup. Scour the non-stick
surface of the griddle with warm soapy water and a non-metal scouring pad.
Rinse thoroughly and dry. Wash grease cup in warm soapy water and dry.
Slide grease cup back into griddle. Recondition the non-stick surface with
cooking oil before using.
7
TEMPERATURE GUIDE
Allow griddle to preheat to temperature shown, unless otherwise noted. Griddle has
reached desired temperature setting when temperature control indicator light goes
off. The quantities of food listed on the following pages are the maximum amount
that can be grilled at one time.
BACON (up to 1 lb.)
EGGS (fried, up to 6)
FRENCH TOAST (4-6
slices)
FISH (up to 1.5lbs.)
FRANKFURTERS
(1.5 lbs)
HAM (2-3 slices)
PANCAKES (4-6)
POTATOES (fried) (up to 1-1/2 lbs.)
FOOD SETTING COMMENTS
300°F
Place bacon on cold griddle. Set heat at
300°F. Turn and separate as bacon cooks,
or separate cold slices with tongs. Fry 5 to
8 minutes per side.
250°F
Fry with or without oil or butter about 3
minutes per side.
350°F
Dip bread in milk-egg mixture. Place bread
on ungreased griddle or sauté in butter.
Bake 2 minutes per side.
350°F
Melt 2 Tbsp. cooking oil or butter on grill.
Start frying skin side up. Fry 4 to 6 minutes
per side.
300°F
May be placed on griddle while it is
preheating. Turn with tongs to prevent
bursting. Total grilling time: 10 to 12
minutes.
325°F
Have slices cut ½” to 1” thick. Score fat
and grill 10 minutes on each side. Add
canned peach halves or pineapple slices
during the last 5 minutes.
350°F
Add 2 Tbsp. melted butter or cooking oil to
package mix batter. Bake until bubbles
appear, turn and brown other side (about 1
minute per side).
350°F
Slice or shred raw or parboiled potatoes.
Add 2 Tbsp. shortening or butter to grill.
Brown potatoes, stirring occasionally.
SANDWICHES (4-6)
SAUSAGE (up to 1.5 lbs)
STEAK (3-4 T-bone
steaks)
WARMING/ SERVING
375°F
300°F
400°F
WARM
(150°F to
175°F)
Place filling between slices of bread.
Spread outside of bread with softened
butter. Grill 3 to 4 minutes per side.
Brown about 8 to 10 minutes per side.
Pork should always be served well done.
Score fat on sirloin, porterhouse, club,
tenderloin or T-bone steak. Grill steak 1”
thick 4 to 6 minutes each side (rare), 5 to 8
minutes (medium), or 8 to 10- minutes (well
done). Turn with tongs.
Place food on griddle to warm. To keep
warm until serving time, turn heat control
down to WARM about 1 minute before
cooking is completed.
8
PRODUCT WARRANTY
Appliance 1 Year Limited Warranty
Focus Electrics, LLC warrants this appliance from failures in the material and workmanship for
one (1) year from the date of original purchase with proof of purchase, provided the appliance
is operated and maintained in conformity with the Focus Electrics Instruction Manual. Any failed
part of the appliance will be repaired or replaced without charge at Focus Electrics
This warranty applies to indoor household use only.
This warranty does not cover any damage, including discoloration, to any non-stick surface of
the appliance. This warranty is null and void, as determined solely by Focus Electrics if the
appliance is damaged through accident, misuse, abuse, scratching, overheating, if the
appliance is altered in any way, or if used outside of an indoor household setting.
THIS WARRANTY IS IN LIEU OF ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES
OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, PERFORMANCE, OR
OTHERWISE, WHICH ARE HEREBY EXCLUDED. IN NO EVENT SHALL FOCUS
ELECTRICS, LLC BE LIABLE FOR ANY DAMAGES, WHETHER DIRECT, INDIRECT,
INCIDENTAL, FORESEEABLE, CONSEQUENTIAL, OR SPECIAL, ARISING OUT OF OR IN
CONNECTION WITH ITS APPLIANCE.
If you think that the appliance has failed or requires service within its warranty period, please
contact the Focus Electrics Customer Service Department at (866) 290-1851 or e-mail us at
housewares@westbend.com. Return shipping fees are non-refundable. Hand-written receipts
are not accepted. Focus Electrics, LLC is not responsible for returns lost in transit.
Valid only in USA and Canada
®
discretion.
REPLACEMENT PARTS
Replacement parts, if available, may be ordered directly from Focus Electrics, LLC online at
www.westbend.com: Replacement Parts. Or you may call or e-mail the service department at
the number/e-mail address listed above, or by writing to us at:
Focus Electrics, LLC
Attn: Customer Service
P.O. Box 2780
West Bend, WI 53095
Be sure to include the catalog/model number of your appliance (located on the bottom/back of
the unit) and a description and quantity of the part you wish to order. Along with this include
your name, mailing address, Visa/MasterCard number, expiration date and the name as it
appears on the card. Checks can be made payable to Focus Electrics, LLC. Call Customer
Service to obtain purchase amount. Your state’s sales tax and a shipping/processing fee will be
added to your total charge. Please allow two (2) weeks for delivery.
This manual contains important and helpful information regarding the safe use and care of
your new Focus Electrics, LLC product. For future reference, attach dated sales receipt for
warranty proof of purchase and record the following information:
Date purchased or received as gift: ______________________________________________
Where purchased and price, if known: ___________________________________________
Item Number and Date Code (shown bottom/back of product): ________________________
L5673 05/07 Focus Electrics, LLC. A Focus Products Group Company Printed in China
9
Loading...
+ 19 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.