WELLS BLOOMFIELD, LLC |
012C |
10 Sunnen Drive P.O.Box 430195 St. Louis, MO 63143 USA telephone: 314-781-2777
fax: 314-781-2714 www.wellsbloomfield.com
OWNERS MANUAL
BUILT-IN FIVE-WELL MODULAR WARMERS with
INFINITE SWITCH CONTROL
MODELS
MOD-500
MOD-500
MOD-500D
MOD-500DM
Includes
INSTALLATION
USE & CARE
EXPLODED VIEW
PARTS LIST
WIRING DIAGRAM
IMPORTANT: DO NOT DISCARD THIS MANUAL
This manual is considered to be part of the appliance and is to be given to the OWNER or MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of this appliance. Additional manuals are available from your WELLS DEALER.
THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any questions concerning installation, operation or maintenance of this equipment.
|
PRINTED IN UNITED STATES OF AMERICA |
p/n 2M-308033 Rev. (-) |
M012C.05 090219 cps |
LIMITED WARRANTY STATEMENT
Unless otherwise specified, all commercial cooking equipment manufactured by WELLS BLOOMFIELD, LLC is warranted against defects in materials and workmanship for a period of one year from the date of original installation or 18 months from the date of shipment from our factory, whichever comes first, and is for the benefit of the original purchaser only.
THIS WARRANTY IS THE COMPLETE AND ONLY WARRANTY, EXPRESSED OR IMPLIED IN LAW OR IN FACT, INCLUDING BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, AND/OR FOR DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH WELLS BLOOMFIELD PRODUCTS. This warranty is void if it is determined that, upon inspection by an authorized service agency, the equipment has been modified, misused, misapplied, improperly installed, or damaged in transit or by fire, flood or act of God. It also does not apply if the serial nameplate has been removed, or if service is performed by unauthorized personnel. The prices charged by Wells Bloomfield for its products are
based upon the limitations in this warranty. Seller’s obligation under this warranty is limited to the repair of defects without charge by a Wells Bloomfield factory authorized service agency or one of its sub-service agencies. This service will be provided on customer’s premises for non-portable models. Portable models (a device with a cord and plug) must be taken or shipped to the closest authorized service agency, transportation charges prepaid, for service. In addition to restrictions contained in this warranty, specific limitations are shown in the Service Policy and Procedure Guide. Wells Bloomfield authorized service agencies are located in principal cities. This warranty is valid in the United States and Canada and void elsewhere. Please consult your classified telephone directory, your foodservice equipment dealer or contact:
Wells Bloomfield, LLC
10 Sunnen Dr., P.O.Box 430129 St. Louis MO 63143 USA phone (314) 781-2777 or fax (314) 781-2714
for information and other details concerning warranty.
SERVICE POLICY AND PROCEDURE GUIDE and ADDITIONAL WARRANTY EXCLUSIONS
1.Resetting of safety thermostats, circuit breakers, over load protectors, and/or fuse replacements are not covered by this warranty unless warranted conditions are the cause.
2.All problems due to operation at voltages or phase other than specified on equipment nameplates are not covered by this warranty.
Conversion to correct voltage and/or phase must be the customer’s responsibility.
3.All problems due to electrical connections not made in accordance with electrical code requirements and wiring diagrams supplied with the equipment are not covered by this warranty.
4.Replacement of items subject to normal wear, to include such items as knobs, light bulbs; and, normal maintenance functions including adjustments of thermostats, adjustment of micro switches and replacement of fuses and indicating lights are not covered by warranty.
5.Damage to electrical cords and/or plug due to exposure to excessive heat are not covered by this warranty.
6.Full use, care, and maintenance instructions supplied with each machine. Noted maintenance and preventative maintenance items, such as servicing and
cleaning schedules, are customer responsibility. Thos miscellaneous adjustments noted are customer responsibility. Proper attention to preventative maintenance and scheduled maintenance procedures will prolong the life of the appliance.
7.Travel mileage is limited to fifty (50) miles from an Authorized Service Agency or one of its sub-service agencies.
8.All labor shall be performed during regular working hours. Overtime premium will be charged to the buyer.
9.All genuine Wells replacement parts are warranted for ninety (90) days from date of purchase on nonwarranty equipment. This parts warranty is limited only to replacement of the defective part(s). Any use of non-genuine Wells parts completely voids any warranty.
10.Installation, labor, and job check-outs are not considered warranty and are thus not covered by this warranty.
11.Charges incurred by delays, waiting time or operating restrictions that hinder the service technician’s ability to perform service are not covered by warranty. This includes institutional and correctional facilities.
SHIPPING DAMAGE CLAIM PROCEDURE
NOTE: For your protection, please note that equipment in this shipment was carefully inspected and packaged by skilled personnel before leaving the factory. Upon acceptance of this shipment, the transportation company assumes full responsibility for its safe delivery.
IF SHIPMENT ARRIVES DAMAGED:
1.VISIBLE LOSS OR DAMAGE: Be certain that any visible loss or damage is noted on the freight bill or express receipt, and that the note of loss or damage is signed by the delivery person.
2.FILE CLAIM FOR DAMAGE IMMEDIATELY:
Regardless of the extent of the damage.
3.CONCEALED LOSS OR DAMAGE: if damage is unnoticed until the merchandise is unpacked, notify the transportation company or carrier immediately, and file “CONCEALED DAMAGE” claim with them.
This should be done within fifteen (15) days from the date the delivery was made to you. Be sure to retain the container for inspection.
xi
TABLE OF CONTENTS
WARRANTY |
xi |
FEATURES & OPERATING CONTROLS |
2 |
PRECAUTIONS & GENERAL INFORMATION |
3 |
AGENCY LISTING INFORMATION |
3 |
INSTALLATION |
4 |
OPERATION |
6 |
MAINTENANCE INSTRUCTIONS |
7 |
CLEANING INSTRUCTIONS |
8 |
TROUBLESHOOTING SUGGESTIONS |
10 |
WIRING DIAGRAM |
10 |
EXPLODED VIEW & PARTS LIST |
11 |
PARTS & SERVICE |
12 |
CUSTOMER SERVICE DATA |
13 |
INTRODUCTION
Thank You for purchasing this Wells Bloomfield appliance.
Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life.
This manual contains the information needed to properly install this appliance, and to use and care for the appliance in a manner which will ensure its optimum performance.
M012C.05 2M-308033 Owners Manual for Five-Well Inf.Sw. MOD-Warmers
SPECIFICATIONS
MODEL |
VOLTS |
WATTS |
|
AMPS 3ø |
|
AMPS1ø |
||
|
|
|
|
|||||
L1 |
L2 |
L3 |
N |
|||||
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
MOD-500 |
208 VAC |
4500W |
15.0A |
11.2A |
11.2A |
0.0A |
21.6A |
|
MOD-500D |
|
|
|
|
|
|
|
|
240 VAC |
6000W |
17.0A |
13.0A |
13.0A |
0.0A |
25.0A |
||
MOD-500DM |
||||||||
|
|
|
|
|
|
|
|
|
1
FEATURES & OPERATING CONTROLS
IMPORTANT:
DO NOT LEAVE ON “PREHEAT”
Unit may cycle on hi-limit control, leading to premature failure of the hi-limit control device.
A.INFINITE SWITCH
1.On INFINITE SWITCH CONTROLLED warmers, power is applied to the heating element based on the control knob position, which varies the duty cycle of the heating element.
2.The desired temperature is controlled by rotating the TEMPERATURE CONTROL KNOB. The knob may have a numeric scale, where higher numbers correspond to higher temperature. LO is the lowest temperature setting; PREHEAT is a “continuous on” setting. Infinite switch controlled warmers are equipped with a hi-limit device to prevent overheating. The hi-limit will self-reset after the warmer has cooled.
3.On warmers equipped with an INDICATOR LIGHT, the light will glow when the infinite switch is in any position other than OFF.
4.The TEMPERATURE CONTROL KNOB will rotate without stopping, with PREHEAT and OFF having obvious detents. The OFF position is a “positive” OFF (i.e. the switch is positively held in the open position).
NOTE: An infinite switch controls temperature by varying the ratio of "on" time to "off" time. Thus, no temperature sensing devise is required.
B.MOUNTING
1.Modular built-in warmers are be equipped with WELLSLOKS, uniquely designed turnout tabs which help secure the warmer top flange to the countertop.
2.See the Installation Instructions, supplied with the particular appliance, for details.
C.DRAINS
1.“D” units (e.g. MOD-500D) have drains for each pan, with each pan having an individual drain valve.
2.“DM” units (e.g. MOD-500DM) have the individual drain lines manifolded together, with a single drain valve for the entire manifold.
Warmers-MOD .Sw.Inf Well-Five for Manual Owners 308033-2M 05.M012C
2
M012C.05 2M-308033 Owners Manual for Five-Well Inf.Sw. MOD-Warmers
PRECAUTIONS AND GENERAL INFORMATION
This appliance is intended for use in commercial establishments only.
This appliance is intended to hold pre-heated food for human consumption. No other use is recommended or authorized by the manufacturer or its agents.
Operators of this appliance must be familiar with the appliance use, limitations and associated restrictions. Operating instructions must be read and understood by all persons using or installing this appliance.
Cleanliness of this appliance is essential to good sanitation. Read and follow all included cleaning instructions and schedules to ensure the safety of the food product.
Disconnect this appliance from electrical power before performing any maintenance or servicing.
This appliance is not jet stream approved. Do not direct water jet or steam jet at this appliance, or at any control panel or wiring. Do not splash or pour water on, in or over any controls, control panel or wiring.
Exposed surfaces of this appliance can be hot to the touch and may cause burns.
Do not operate this appliance if the control panel is damaged. Call your Authorized Wells Service Agent for service.
The technical content of this manual, including any wiring diagrams, schematics, parts breakdown illustrations and/or adjustment procedures, is intended for use by qualified technical personnel.
Any procedure which requires the use of tools must be performed by a qualified technician.
This manual is considered to be a permanent part of the appliance. This manual and all supplied instructions, diagrams, schematics, parts breakdown illustrations, notices and labels must remain with the appliance if it is sold or moved to another location.
This appliance is made in the USA. Unless otherwise noted, this appliance has American sizes on all hardware.
WARNING:
SHOCK HAZARD
All servicing requiring access to non-insulated electrical components must be performed by a factory authorized technician.
DO NOT open any access panel which requires the use of tools. Failure to
follow this warning can result in severe electrical shock.
CAUTION:
RISK OF 
DAMAGE
DO NOT connect or energize this appliance until all installation instructions are read and followed. Damage to the appliance may result if these instructions are not followed.
CAUTION:
HOT SURFACE
Exposed surfaces can be hot to the touch and may cause burns.
AGENCY LISTING INFORMATION
Refer to the product nameplate for the specific appliance for agency listings. In general:
This appliance conforms to NSF Standard 4 for sanitation only if installed in accordance with the supplied Installation Instructions.
UL Listed warmers are UListed under UL File E6070.
STD 4
E6070
UL Listed Warmers
3
Loading...