Wells MOD-100 Installation Manual

ELECTRICAL

INSTALLATION INSTRUCTIONS
BUILT-IN MODULAR WARMERS

MOD-100 SERIES (T, TD)

PHASEMODELS WATTSVOLTS AMPS

MOD-100

MOD-100 900208 4.3 SINGLE

MOD-100

MOD-100T 1650120 13.8 SINGLE 14 AWB Cu

MOD-100T

MOD-100T 1650240 6.9 SINGLE 12 AWB Cu

MOD-100EUT 220-240 1650 6.9 SINGLE 1.5 mm

ALL MODELS WITH A "D" SUFFIX HAVE THE SAME ELECTRICAL SPECIFICATIONS AS THE STANDARD MOD-100 AND MOD-100T MODELS

120

240

208

1200

1200

1240

10.0 SINGLE

5.0 SINGLE 12 AWB Cu

6.0 SINGLE 12 AWB Cu

FIELD
WIRING
GAUGE

14 AWB Cu

12 AWB Cu

CUTOUT DETAILS

3 1/8

20 3/4

4 1/8

(105)

12 3/4

(324)

TOP CUTOUT FRONT PANEL CUTOUT

(527)

(79)

4 7/8

(124)

5

(127)

CLEARANCES

MINIMUM CLEARANCE REQUIRED FROM

UNIT TO THE NEAREST SURFACE.

FRONTBOTTOMSIDEBACK

4 1/86 3/411
(105)(171)(25)(25)

TEMP.

RATING

90°C

75°C

75°C

90°C

75°C

75°C

2

90°C

INCHES

(MM)

PRODUCT DIMENSIONS

6 7/8

(175)

13 3/4

(349)

INSTALLATION INSTRUCTIONS

INSTALLER MUST MEET CONDITIONS OF ACCEPTABILITY
OUTLINED BELOW UPON INSTALLATION:

1. Required Installation Clearances:
Wooden and Metal Installation: DO NOT install closer than
4 1/8 inches to front wall, 1 inch to back and side walls,
and 6 3/4 inches to a surface below the unit. If the
control box is located below the unit, the front clearance
may be 1 inch.

2. Unit shall be accessible for servicing from the bottom.

3. If storage is to be used underneath the unit, it is
recommended that a baffle be placed 8 1/2 inches below
the unit to avoid contact with elevated temperatures.

TO FABRICATE:

1. Layout "cutout" dimensions on countertop and front
apron.

2. Layout and fabricate control panel holes in counter
apron using the control box as a template.

3. Cut out holes.

4. Unit shall be accessible for servicing from the bottom.

TO INSTALL:
IMPORTANT - DO NOT disconnect "lead wires" from the
Master Control Panel when making installation.

1. Tilt and pass Control Panel and electrical box through
the countertop cutout, then through the apron cutout.
Lower modular section into countertop cutout and position.
RECOMMENDATION: Before final seating of modular section
to countertop, apply a bead of silicone adhesive/sealant
to underside of gray gasket material supplied on the
mounting flange.

2. From underneath, insert screwdriver into "slots" in
Wellslok frame and twist "ears" outward (clockwise) as
required to secure flange tightly to countertop.

3. Mount Control Box to apron cutout as shown in
drawing.

4. Mount Control Panel onto electrical box using the screws
supplied.

TO PLUMB:

1. Warmers with a 'D' suffix are supplied with individual 1/2''
female N.P.T. drains.

2. Connect to suitable drain line.

TO WIRE:

1. Final connection is accomplished by bringing proper power
supply leads (see 'wiring requirements' label) through conduit
knockout to wire leads supplied within the Master Control
Panel. Check nameplates for voltage and phase.

2. Do not connect to a circuit operating at more than 150
volts to ground. (240 volt models only).

NOTE: INSTALLATION MUST MEET LOCAL PLUMBING AND

ELECTRICAL CODES.

WARMER FLANGE

GASKET

WELLSLOK

SCREWDRIVER

COUNTERTOP

WELLS/BLOOMFIELD * VERDI, NV

21 3/4

(552)

2 1/4

(57)

6 1/4

(159)

9 3/4

(248)

1/2 INCH

5 7/8

(149)

IMPORTANT:
MOUNT APPLIANCE SO THAT THE
CONTROL PANEL IS LOCATED TO
THE FRONT OF THE FIXTURE.

INTERNAL N.P.T.
'D' MODELS ONLY

37099-1 REV (-)

MASTER
CONTROL
PANEL

1 3/4

(44)