Welch Allyn®
DEVICE WITH
FLEXIPORT FITTING
CALIBRATION TEST EQUIPTMENT
WITH FLEXIPORT TEST FITTING
FlexiPort
Directions for Use
®
Calibration Check Fitting
Mat’l #714198 Ver. C
Welch Allyn USA (Headquarters)
Tel: 1-315-685-4560 or 1-800-535-6663
Fax: 1-315-685-0054
Welch Allyn Ireland
(European Customer Service)
Tel: (353) 46 90 67700
Fax: (353) 46 90 67755
Welch Allyn Italy
Tel: (+39) 02-6968- 2425
Fax: (+39) 02-6963-3697
Welch Allyn France
Tel: (+33) 60 09 33 66 or (+33) 55 69 58 49
Fax: (+33) 60 09 67 97
Welch Allyn China
Tel: (+86) 21 6327 9631
Fax: (+86) 21 6327 9632
Welch Allyn U.K.
Tel: 0-207-365-6780
Fax: 0-207-365-9694
Welch Allyn Germany
Tel: (+49) 7477 9271 70
Fax: (+49) 7477 9271 90
Welch Allyn Spain
Tel: (+34) 917499357
Fax: (+34) 917499361
Welch Allyn Singapore
Tel: (+65) 291-0882
Fax: (+65) 291-5780
Welch Allyn Australia
Tel: (+61) 2-9638-3000
Fax: (+61) 2-9638-3500
Welch Allyn Japan
Tel: (+81) 3-219-0071
Fax: (+81) 3-219-0074
Welch Allyn South
Africa
Tel: (+27) 11 777 7509
Fax: (+27) 11 777 7510
Intended Use
This test fitting is intended to enable connection between FlexiPort fittings on blood pressure
devices and calibrated equipment during calibration check procedures.
Contraindications
This test fitting should not be used during blood pressure readings on patients.
Warnings
A warning statement in this manual identifies a condition or practice which, if not corrected or
discontinued immediately could lead to injury, illness, or death.
Maintenance
Clean as required.
Directions For Use
To connect the test fitting with the Flexiport fitting, match up the base of the Flexiport fitting with
the base of the test fitting. Gently push together until the fittings click, ensuring a successful
connection.
WARNING: Ensure an airtight seal at all connection points prior to use.
Welch Allyn Canada
Tel: 1-905-890-0004
Fax: 1-905-890-0008
Welch Allyn Inc. • 4341 State Street Road • Skaneateles Fall, NY 13153 USA
Tel : 800-535-6663 (USA only) or 315-685-4560 • Fax: 315-685-3361 • www.welchallyn.com
U.S. Patents 6,578,428; 6,036,718; and additional patents pending.
© 2009 Welch Allyn, Inc. All rights reserved. No one is permitted to reprodu ce or duplicate, in any form, this manual or any
part thereof without permission from Welch Allyn. Welch Allyn assumes no responsibility for any injury to anyone, or for
any illegal or improper use of the product, that may result from failure to properly use the product in accordance with the instructions,
cautions, warnings, or statement of inten ded use published in this manual. Welch Allyn® and FlexiPort® are trademarks of Welch Allyn,
Inc.
Warranty
Welch Allyn warrants the FlexiPort Test Fitting, when new, to be free of defects in material and workmanship and to
perform in accordance with manufacturer’s specifications for a period of one year from the date of purchase from Welch
Allyn or its authorized distributors or agents. Welch Allyn will either repair or replace any components found to be
defective or at variance from manufacturer’s specifications within this time at no cost to the customer. It shall be the
purchaser’s responsibility to return the FlexiPort Test Fitting to Welch Allyn or an authorized distributor, agent, or service
representative. This warranty does not include breakage or failure due to tampering, misuse, neglect, accidents,
modification, or shipping. This warranty is also void if the instrument is not used in accordance with manufacturer’s
recommendations or if repaired by other than Welch Allyn or an authorized agent. Purchase date determines warranty
requirements. No other express warranty is given.
After a calibration test is complete, gently squeeze the side tabs of the port fitting and pull apart
to disconnect the fittings.