R Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
www.weedeater.com
Instruction Manual
SG / TE / XT Series
ENGLISH
WARNING:
Read and follow all Safety Rules and Operating Instructions before using this product. Read instructions carefully before assembling.Failuretodosocanresultinseriousinjury.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
CopyrightE2003 Electrolux Home Products, Inc.
Electrolux Canada Corporation
6150 McLaughlin Road
Mississauga, Ontario L5R 4C2
530084129
2/11/03
SAFETY RULES
WARNING:
gardening appliances, basic safety precautionsshouldalways befollowedtoreduce the risk of fire, electric shock, and
serious injury. Read and follow all
instructions.
This power unit can be dangerous!
torisresponsibleforfollowing thewarnings
and instructions in this manual and on the
unit. Read entire instruction manual before
using unit! Be thoroughly familiar w ith the
controls and the proper use of the unit. Restrict the use of this unit to persons who
read, understand, and follow unit and
manualwarningandinstructions. Neverallow children to operate this unit. Close
attention is necessary when used near
children.
DANGER:
ingdevices.Unitisdesignedfor line trimmeruse only.Useof any other accessories or attachments will increase the risk
of injury.
WARNING:
objects violently. You and others can be
blinded/injured. Wear safety glasses,
boots, and leg protection. Keep body
parts clear of rotating line.
Safety Glasses or similar eye protection
Boots
Keep children, bystanders, and animals
50 feet (15 meters) away. If approached
stop unit immediately.
If situations occur which are not covered
in this manual, use care and good
judgement. If you need assistance,
contact your Authorized Service Dealer
or call 1-800-554-6723.
When using electric
SAFETY INFORMATION
ON THE UNIT
Opera-
Neverusebladesorflail-
Trimmer line throws
Hazard Zone
15 m
50 ft.
OPERATOR SAFETY
S
Dress properly. Always wear safety
glasses or similar eye protection when
operating or performing maintenance on
your unit. (Safety glasses are available.)
Always wear face or dust mask if operation is dusty . Always wear heavy, long
pants, long sleeves, boots, and gloves.
Do not go barefoot or wear sandals.
S
Secure hair above shoulder length.
Secure or remove loose clothing and
jewelryorclothingwith loosely hanging
ties, straps, tassels, etc. They can be
caught in moving parts.
S
Being fully covered also helps protect
you from debris and pieces of toxic
plants thrown by spinning line.
S
Stay alert.Do not operate unit whenyou
are tired, ill, upset or under the influence
of alcohol, drugs, or medication. Watch
whatyouaredoing;usecommonsense.
S
Avoid unintentional starting of the unit.
Never carry unit with your finger on the
switch. Be sure the switch is in
position and never touch the switch
when connecting extension cord.
ELECTRICAL SAFETY
WARNING:
Avoidadangerous environment. Toreduce the risk of electrical shock, do not use in rain, in damp or
wet locations, or around swimming
pools, hot tubs, etc. Do not expose to
snow,rain,orwatertoavoidthepossibility of electrical shock.
S
Use a voltage supply shown on unit.
S
Avoid dangerous situations. Do not use
in the presence of flammable liquids or
gases to avoid creating a fire or explosion and/or causing damage to unit.
S
Toreducethe risk of electrical shock, this
appliance has a polarized plug (one
blade is wider than the other) and will require the use of a polarized extension
cord. The appliance plug will fit into a polarized extension cord only one way. If
the plug does not fit fully into the extensioncord,reversetheplug.Iftheplug still
doesnotfit,obtainacorrectpolarizedextension cord. A polarized extension cord
will require the use of a polarized wall
outlet. This plug will fit into the polarized
wall outlet only one way.If plug does not
fit fully into the wall outlet, reverse the
plug. If the plug still does not fit, contact a
qualified electrician to install the proper
walloutlet. Donotchangetheequipment
plug, extension cord receptacle, or extension cord plug in any way.
S
To reduce risk ofelectrical shock, use
extension cordsspecifically markedas
suitable for outdoor appliances having
2
OFF
electrical rating not less than the rating
of unit. Cord must be marked with suffix “W--A” (in Canada “W”). Make sure
your extension cord is in good condition. Inspect extensioncordbeforeuse
and replace if damaged. Do not use a
damaged cord. Cord insulation must
be intact with no cracks or deterioration. Plug connectors must be undamaged. An undersized extension cord
will cause a drop in line voltage resultinginlossofpowerand overheating. If
in doubt, use the next heavier gauge.
The lower the gauge number, the
heavier the cord (see
TENSION CORD
SELECT AN EX-
). Do not use multiple
cords.
S
Donotabusecord.Nevercarrytheunit
by the extension cord or yank extension cord to disconnect unit.
S
Use cord retainer to prevent disconnection of extension cord from unit.
ATTACHTHEEXTENSION CORDTO
See
YOURTRIMMER
.
tion
S
Do not use the unit if the switch does
inthe
OPERATION
notturnthe unit onandoff properly.Repairs to the switch must be made by
your authorized service dealer.
S
Keep the extension cord clear of operator and obstacles at all times. Do not
expose cords to heat, oil, water, or
sharp edges.
S
To avoid the possibility of electric
shock, avoid body contact with any
grounded conductor, such as metal
fences or pipes.
S
GroundFaultCircuitInterrupter (GFCI)
protection should be provided on circuit or outlet to be used. Receptacles
are available having built-in GFCI
protection and may be used for this
measure of safety.
UNIT SAFETY
S
Inspect unit before use. Replace damaged parts. Make sure all handles,
guards, and fasteners are in place and
securely fastened. Parts that are damaged must be repaired or replaced by
an authorized service dealer. This includes head parts that are cracked, or
chipped, guards, and any other part
that is damaged.
S
Do not repair unit yourself.
S
Use only 0.065” (1.65 mm) diameter
recommendedtrimmerline(see
SORIES
). Never use wire, rope, string,
ACCE-
etc.
S
Use specified trimmer spool. Make
sure spool is properly installed and all
parts are securely fastened.
sec-
S
Use only recommended Weed Eater
replacement parts and accessories.
CUTTING SAFETY
S
Inspectareato becut.Removeobjects
(rocks, brokenglass,nails,wire,string,
etc.) which can be thrown or become
entangled in cutting head.
S
Do not overreach or stand on unstable
support. Keep firm footing and balance.
S
Keep the cutting head below waist level. Do not raise handles above your
waist. Cutting head can come dangerously close to your body.
S
Keepawayfromcuttingheadandspinning line.
S
Use unit properly. Use only for trimming, edging, and mowing. Do not
force unit; it will do the job better and
with less risk of injury at the rate for
which it was designed.
S
Use only in daylight or in good artificial
light.
MAINTENANCE SAFETY
WARNING:
Disconnect unit from
the power supply before performing
maintenance, orwhenchangingtrimmer
line.
S
Maintain unit according to recommended procedures. Keep cutting line
atproperlength.Followinstructions for
changing trimmer line.
S
Have all service and maintenance not
explained in this manual performed by
an authorized service dealer to avoid
creating a hazard.
S
Never douse or squirt the unit with water
or any other liquid. Clean unit and labels
with a damp sponge. Keep handles dry,
clean, and free from oil and grease.
S
Keep the air vents clean and free from
debris to avoid overheating the motor.
Clean after each use.
TRANSPORTING AND STORAGE
S
Stoptheunitanddisconnect thepower
source when not in use.
S
Carry the unit with motor stopped.
S
Store the unit so that the line limiter
blade (on underside of shield) c annot
cause injury.
S
Store unit indoors in a high, dry place
out of the reach of children. Store unit
unplugged.
DOUBLE INSULATION
CONSTRUCTION
This unit is double insulated to help protect against electric shock. Double insulation construction consists of two
separate “layers” of electrical insulation
instead of grounding.
r
3
Toolsbuiltwiththisinsulation system are
notintendedtobegrounded. No grounding means is provided on this unit, nor
should a means of grounding be added
to this unit. As a result, the extension
cord used with your unit can be plugged
into any standard 120 volt electrical outlet.
Safety precautions must be observed
when operating any electrical tool. The
double insulation system only provides
added protection against injury resulting
from an internal electrical insulation failure.
WARNING:
this unit, including housing, switch, motor,etc., must bediagnosedand repaired
by qualified service personnel. Replacement parts for a double insulated appliance must be recommended by the
manufacturer. A double insulated appliance ismarkedwiththewords“double
insulation” or “double insulated.” the
symbol (square within a square)
alsobemarkedonthe appliance.Failure
tohavetheunitrepairedbyqualifiedservice personnel can cause the double insulation construction to become ineffective and result in serious injury.
SAVE THESE INSTRUCTIONS
All electrical repairs to
may
ALIGN INSTALLATION ARROWS
Twist shield in
direction of
arrow to assemble
CAUTION:
NOTE:
anextendabletube. Extendthetubeuntil
it snaps into place. Without the tube fully
extended the Twist ’N Edge feature on
the XT series will not operate.
Sharp line limiter blade
Place handle in
comfortable
position and
tighten securely.
SG&XT units are equipped with
ASSEMBLY
WARNING:
assembled, check each step to insure
your unit is properly assembled. Follow
all safety information in the manual and
on unit.
WARNING:
properly installed. The shield provides
partial protection from the risk of thrown
objects to the operator and others. Your
unit is equipped with a line limiter blade,
which cuts excess line to the proper
length while running. The line limiter
blade (on underside of shield) is sharp
and can cut you.
NOTE:
damage to unit (including motor failure)
will result.
If shield is not properly installed,
If you receive your unit
The s hield must be
Extendable tube
(Some models)
CAUTION:
tended for the unit to operate correctly.
The tube must be fully ex-
USING YOUR UNIT
Use only a voltage supply as specified
on your unit.
SELECT AN EXTENSION CORD
Extension Cord Gauge Chart
Length of Cord Gauge
25 Ft. (7.5 m)
50 Ft. (15 m)
100 Ft. (30 m)
Extension cords are available for this
unit.
ATTACH THE EXTENSION
CORD TO YOUR TRIMMER
Loop your extension cord through the
handle and around the hook. Insure the
plug and cord are firmly and fully engaged.
4
18 Gauge
16 Gauge
16 Gauge
Metal Blade
TAP
Cutting
Head
CORRECT OPERATING POSITION
(XT & TE)
Trimming
WARNING:
Always wear eye pro-
Edging
tection. Never lean over the trimmer
head. Rocks or debris can ricochet or be
thrown into eyes and face and cause
blindness or other serious injury.
When operating unit, stand as shown and
check for the following:
S
Weareyeprotection and heavy clothing.
S
Hold trigger handle with right handand
assist handle with left hand.
S
Keep unit below waist level.
S
Cutfromyour right toyourleft to ensure
debris is thrown away from you. Without bending over, keep line near and
parallel to the ground (perpendicular
when edging) and not crowded into
material being cut.
ADJUSTING UPPER HANDLE
(XT Series only)
S
Press button located on the underside
oftheupperhandleandextendhandle
to a comfortable position.
Button
ADVANCING THE CUTTING LINE
Toadvancetheline,tapthebottom of the
cuttingheadon thegroundwhile thetrimmer is running at full speed. The metal
blade attached to the shield will cut the
line to the proper length.
TWIST ‘N EDGErFEATURE
XT&TEseriesunitsareequippedwitha
button on the side of the unit. If your unit
includes this feature you can press this
button and twist the lower portion 180
counterclockwise into an edging position.
Twist ‘N Edge Button
MAINTENANCE
WARNING:
source before performing maintenance.
GENERAL RECOMMENDATIONS
The warranty on this unit does not cover
itemsthathave beensubjectedtooperator abuse or negligence. To receive full
value from the warranty, the operator
must maintain unit as instructed in this
manual.Various adjustmentswillneedto
be made periodically to properly maintain your unit.
BEFORE EACH USE
CHECK FOR LOOSE FASTENERS
AND PARTS
S
Housing Screws
S
Assist Handle
S
Debris Shield
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for
replacement of damaged or worn parts.
S
Trigger Switch -- Ensure switch functions properly by pressing and releasingthetrigger switch. Make sure motor
stops.
S
DebrisShield -- Discontinue use of unit
if debris shield is damaged.
AFTER EACH USE
INSPECT AND CLEAN UNIT AND LABELS
S
After each use, inspect complete unit
for loose or damaged parts. Clean the
unit using a damp cloth with a mild detergent.
S
Wipe off unit with a clean dry cloth.
5
Disconnect power
_
SERVICE
REPLACING THE LINE
S
Disconnectunitfromthepowersource.
S
Remove the s pool by firmly pulling on
the tap button.
S
Clean entire surface of hub and spool.
S
Replacewithapre-woundspool,orcuta
length of30feetof 0.065diameterWeed
Eaterrbrand line. Use of heavier line
could overload and damage the unit.
Never use wire, rope, string, etc., which
can break off and become a dangerous
missile.
S
Insert one end of the line about 1/2 inch
(1cm)intothesmall slot inside the spool.
Small
Hole
S
Wind the line evenly and tightly onto
the spool. Wind in the direction of the
arrow found on the spool.
S
Push the line into the notch, leaving 3
to 5 inches (7 -- 12 cm) unwound.
S
Insert the line into the exit hole in the
hub as shown i n the illustration.
Line in
Notch
Hub
Spool
Line exit hole
S
Align the notch with the line exit hole.
S
Push the s pool into the hub until it
snaps into place, while keeping light
tension on the end of the line.
S
Pullonthe line extendingoutsideofthe
hub to release it from the notch; otherwise, the unit will not function properly.
STORAGE
WARNING:
steps after eachuse.
S
Stoptheunitanddisconnect thepower
source when not in use.
S
Carry the unit with motor stopped.
S
Store the unit so the line limiter blade
cannot cause injury.
S
Store unit and extension cord indoors
in a high, dry place out of the reach of
children. Store unit unplugged.
S
Storeunitwithall guards in place.Position unit so that any sharp object cannot accidentally cause injury.
Perform the following
NEED ASSISTANCE?
For assistance, or a replacement part
call: 1-800-554-6723.
Safety Glasses 952701645
Spool with 30’ line 952701663
50’ coil of bulk line. 952701550
100’ coil of line. 952701533
200’ coil of line. 952701594
6
TROUBLESHOOTING TABLE
WARNING:
Alwaysstopunit anddisconnectfromthe powersourcebefore
performingalloftherecommended remediesbelowexceptremedies that require operation of the unit.
TROUBLE CAUSE REMEDY
Semi-automatic
head stops
under a load or
does not turn
when switch is
pressed.
Line does not
advance or
breaks while
cutting.
Line welds onto
spool.
Line releases
continuously.
Line usage is
excessive.
Line pulls back
into head.
1. Crowding trimmer line
against material being
cut.
2. Electrical failure.
3. Thrown circuit breaker.
4. Debris stopping head.
1. Line improperly routed
in head.
2. Line improperly
wound onto spool.
3. Incorrect line size
4. Not enough line
outside of head.
5. Dirt buildup on unit.
1. Line size is incorrect.
2. Incorrect spool.
3. Line is being crowded
against material being
cut.
1. Line improperly
routed in head.
2. Spool damaged.
1. Line improperly routed
in head.
2. Line size is incorrect.
3. Crowding line against
material being cut.
4. Spool worn or damaged.
1. Too little line outside
of head.
2. Line size incorrect.
1. Allow tip of line to do the cutting.
2. Contact your authorized service dealer.
3. Check Breaker Box.
4. Remove debris.
1. Check line routing.
2. Rewind line tightly and evenly.
3. Use only .065 in. (1.65mm) dia. line.
4. Remove cover and pull 4 in.
(10 cm) of line out of head.
5. Clean unit.
1. Use only .065 in. (1.65mm) dia. line.
2. Replace with correct spool.
3. Cut with tip of line fully extended.
1. Check line routing.
2. Replace spool.
1. Check line routing.
2. Replace spool.
3. Cut with tip of line fully extended.
4. Replace spool.
1. Remove cover and pull 4 in.
(10 cm) of line outside of head.
2. Use only .065 in. (1.65 mm) dia. line.
7
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS,
INC.,
warrants to the original purchaser
that each new
Weed Eater
tric or cordless product is free from defects in material and workmanship and
agrees to repair or replace under this
warranty any defective
brand electric product within two (2)
years from the original date of purchase.
If your
Weed Eater
cordless product should fail within the
limited warranty period, return it, complete, prepaid, with proof of purchase, to
the dealer from whom it was purchased
for repair or replacement at the option of
ELECTROLUX HOME PRODUCTS,
INC.
This warranty is not transferable and
does not cover damage or liability
caused by improper handling, improper
maintenance or the use of accessories
and/or attachments not specifically recommended by
ELECTROLUX HOME
PRODUCTS, INC.,
uct. Additionally, this warranty does not
cover parts that will wear and require replacement with reasonable use during
r
brand elec-
Weed Eater
brand electric or
for this electric prod-
the warranty period. This warranty does
not cover predelivery set--up or normal
adjustments explained in the instruction
manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EXPRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
The policy of
PRODUCTS, INC.,
prove its products. Therefore,
TROLUX HOME PRODUCTS, INC.,
ELECTROLUX HOME
istocontinuouslyim-
ELEC-
reserves the right to change, modify, or
discontinue models, designs, specifications, and accessories of all products at
any time without notice or obligation to
any purchaser.
8
Loading...