Weber 42370 User Manual
A
S
f
(
SUMMIT
®
PLATINUM D4 / D6
BUILT-IN NG GAS GRILL INSTALLATION GUIDE
THIS GAS APPLIANCE IS DESIGNED
FOR OUTDOOR USE ONLY.
42370
LOCATING YOUR GRILL
When determining a suitable location for your Summit® gas grill installation, give attention to concerns such as exposure to wind, proximity to traffi c paths, and
keeping any gas supply lines as short as possible. Never locate the Summit® gas grill in a garage, breezeway, shed, under an unprotected overhang, or other
enclosed area. Locate the grill and structure so there is enough room to safely evacuate the area in case of a fi re.
CLEARANCE FROM SURFACES OR STRUCTURES
24 inches (61 cm) Any Surface
WARNING: Clearance from any surface or structure is
24 inches (609.6 mm) from the back and sides of the grill.
Refer to “Typical Gas Supply Installation” before starting
installation.
WARNING: The structure, “island”, countertops, and
adjacent work areas for the built-in grill installation must be
built from noncombustible materials only.
NOTE: If you have questions on what materials are considered noncombustible,
contact your local building materials supplier or fi re department.
BUILT-IN STRUCTURE CUTOUT DIMENSIONS
ALL DIMENSIONS ARE TO FINISHED SURFACES.
Any Surface
24 inches
24 inches
(61 cm)
27 inches (685.8 mm) min. for
lid clearance
Grill Frame
Note: For a countertop treatment: Recommended 3/4 inch
19.1 cm) overhang. Notch front edge for frame to fully
slide in.
(61 cm)
WARNING: All countertop fi nished surfaces must be
constructed of a noncombustible material.
ny
ur
ace
3
2
1
1
2
3
Built-In Cutout Dimensions
D4 D6 Tolerances
1
30
˝ 38
/
4
1
˝ 34
/
34
4
21˝ 21˝ +
1
˝+
/
4
1
˝+
/
4
1
” -
/
4
1
” -
/
4
1
” -
/
4
42370 US 10/01/05
1
˝
/
4
1
˝
/
4
1
˝
/
4
NG
2
BUILT-IN CUTOUT DIMENSIONS
GENERAL CONSTRUCTION DETAILS
Summit® Built-In unit and all other accessory units should be on site before construction begins. All dimensions have a tolerance of plus or minus (+/-) 1/4
inch.The grill frame rests directly on the Island Structure top fi nished surface. Make sure this surface is level. Do not support the grill from the bottom. If the
supporting structure is going to have an electrical outlet for a rotisserie, it should be on the left side of the structure.
24"
min.
24"
min.
6
3
1
"
/
4
34
30
21"
1
"
/
4
1
"
/
4
Built-In
Frame
Note: For a countertop treatment:
Recommended
Notch front edge for frame to fully slide in.
3
inch overhang.
/
4
Access for electric
on left hand side
4B
24"
min.
3
"
/
4
Gas Inlet
min.
Side Burner
Opening
27 inches min.
1
6
"
/
4
3
3
/
4
Gas Inlet
1/2"
10
distance from front
edge of the cutout
for open lid clearance
*Clearance from any surface or structure is at least 24 inches from the back and
sides of the grill.
"
24"
min.
24"
min.
6
3
1
"
/
4
34
1
"
/
4
21"
38
1
"
/
4
Built-In
Frame
Note: For a countertop treatment:
Recommended
Notch front edge for frame to fully slide in.
3
inch overhang.
/
4
Access for electric
on left hand side
6B
24"
min.
3
"
/
4
Gas Inlet
min.
Side Burner
Opening
27 inches min.
1
6
"
/
4
3
"
/
3
4
Gas Inlet
1/2"
10
distance from front
edge of the cutout
for open lid clearance
*Clearance from any surface or structure is at least 24 inches from the back and
sides of the grill.
4B
PARTS LIST
3
Lid - 1
Cookbox - 1
Lid - 1
6B
OR
Left Door - 1
Right Door - 1
Warming Rack - 1
Warm-Up
Right Enclosure Panel - 1
™
Rack - 1
Cookbox - 1
Front Frame Rail - 1
Rear Frame Rail - 1
Rear Panel
Assembly- 1
Left Enclosure Panel - 1
Front Vent Panel - 1
Rear Vent - 1
Bottom Shelf - 1
4
PARTS LIST (CONTINUED)
Flavorizor
Stainless Steel
Cooking Grates
®
Bars - 2 Sets
4B
6B
Bottom Tray - 1
Catch-Pan Holder - 1
- 2
- 3
Wrench - 1
x10 Sheet Metal Screws - 3
Plastic Anchors - 3
1/2 inch Bolts
(1/4 x 20 x 1/2 inch Bolt) - 8
#10-32 x 1/4 inch Steel Screws - 5
Nylon Washer - 8
1/2" Flare Gasket - 2
Catch-Pan - 1
Disposable Drip Pans - 2
Hinge Pin- 2
Hair Pin Cotter- 2
Corrugated gas line - 1
Right Front Vent Clip - 1
3/8" Flare Gasket - 2
Handle - 2
Handle Hardware - 4
Rotisserie - 1
Rotisserie Motor - 1
Rotisserie Bracket - 1
Keps Nuts (1/4 x 20 Blk Zinc) - 2
Left Front Vent Clip - 1
7/16 inch Wrench - 1
Rotisserie Bracket Hardware- 2
Smoker - 1
EXPLODED VIEW - PLATINUM D4
5
5340501 - Summit® Platinum D4 NG Built-In 091905
1
2
3
38
4
39
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
5
6
7
8
9
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
28
29
30
31
32
33
34
35
36
37
66
67
68
69
70
71
72
73
74
75
76
77
6
EXPLODED VIEW LIST - PLATINUM D4
1. Hinge Pin
2. Thermometer Hardware
3. Thermometer Bezel
4. Warm-Up
™
Basket
5. Smoker Assembly
6. Flavorizer
®
Bar Assembly w/ Smoker
7. Smoker Box Chip Grate
8. Rotisserie Motor
9. Motor Bracket
10. Motor Bracket Screw
11. 1/4 - 20 inch Keps Nut
12. Smoker Electrode Assembly
(10 1/2 inch wire)
13. Electrode Assembly (8 3/4 inch wire)
14. Crossover
®
Tube
15. Smoker Burner Tube
16. Left Burner Tube
17. 10 - 24 x 1/2 inch Black Screw
18. Manifold
19. Negative Ignition Switch Wire
20. Positive Ignition Switch Wire
21. Four Output Ignition Module Assembly
22. Ignition Switch Button Assembly
23. 10 - 24 x 1/2 inch Black Screw
24. Small Control Knob
25. Control Knob
26. Control Panel
27. Front Panel
28. Vent Cover Assembly
29. Front Frame Rail
30. Left Rear Panel
31. Left Panel
32. Handle Assembly
33. Bottom Shelf
34. Toe Kick Vent
35. Left Vent Bracket
36. Left Door Assembly
37. Right Door Assembly
38. Hair Pin Cotter
39. Lid Assembly
40. 1/4 - 20 x 1 1/4 inch Bolt
41. IR Rain Cover Hardware
42. 12 inch Cook Grate
43. IR Rain Cover
44. 10 - 24 x 1/2 inch Stainless Steel Screw
45. Right Flavorizer® Bar Assembly
46. IR Burner
47. IR Cover Box
48. Warming Rack
49. Thermocouple
50. IR Gas Line
51. IR Electrode Wire
52. Rotisserie Fork Screw
53. Rotisserie Fork
54. Rotisserie Shaft
55. Cookbox Assembly
56. Electrode Assembly (16 1/4 inch wire)
57. Right Burner Tube
58. Heat Shield
59. Battery Shield Assembly
60. Main Gas Line
61. Bulkhead Assembly
62. Bottom Tray
63. Summit Catch Pan Holder
64. Summit Catch Pan
65. Summit Drip Pan
66. Rear Frame Rail
67. Rear Vent Hardware
68. Rear Panel Hardware
69. Right Rear Panel
70. Right Panel
71. 10 -16 x 3/4 Screw w/ Washer
72. Plastic Plug
73. Door Stop
74. Door Bushing
75. Door Plug
76. 1/4 - 20 x 1/2 inch Black Bolt
77. Right Vent Bracket
Loading...