Wayne-Dalton 9900, 9200, 9600 User Manual

ST ART HERE

9200 - Foamcore™ 9600 - Thermogard

9900 - Thermowayne™

13A-13C

Shake the torque tube gently to extend the winding shafts out about 5" on each side. For single spring applications, there will be no left hand winding shaft in the torque tube.

IMPORTANT! READ IMPORTANT SAFETY NOTICES AND REFER TO INSERT SHEET INSTRUCTIONS

TITLED “REMOVING THE OLD DOOR/PREPARING THE OPENING”. IF THE INSERT SHEET INSTRUCTIONS ARE NOT INCLUDED, CONTACT WAYNE-DALTON CORP. FOR A FREE COPY. If removing an existing door, carefully follow the directions given on the insert sheet instruction in the portion titled “Removing the Old Door”.

WARNING!

REMOVAL OF AN EXISTING DOOR CAN BE DANGEROUS. FOLLOW INSERT SHEET INSTRUCTIONS CAREFULLY, OTHERWISE SERIOUS INJURY OR DEATH COULD RESULT.

Begin the installation of the door by checking the opening. It must be the same size as the door. Vertical jambs must be plumb and the header level. Side clearance, from edge of door to wall, must be minimum of 3-1/2” (89 mm) on each side. For proper opening preparation refer to the portion of the insert sheet instructions titled “Preparing the Opening”. Follow the steps below. The steps correspond to the illustrations on the garage door layout.

NOTE: It is recommended that 5/16” x 1-5/8” lag screws be pilot drilled using a 3/16” drill bit, and 1/4” x 2” lag screws

and 1/4” x 1-1/2” lag screws be pilot drilled using a 1/8” drill bit, prior to fastening.

1A-1C

Put the lower T wistlock tab on the flagangle into the Twistlock hole in the vertical track. Give the flagangle 1/4 turn to lock in place. Repeat for other side.

2A-2C

Using a hammer, tap the horizontal angle towards the curved end of the track until the hole in track and angle are aligned. Set tracks aside.

NOTE: For larger size doors, a full length horizontal angle is already spot welded to the horizontal track.

Measure the length of the vertical tracks. Using the jamb bracket schedule (located on backside), determine the placement of the jamb brackets for your door height.

T orqueMaster™ drums are marked right and left. Make sure you place the cable from the right hand drum on the right hand bottom bracket, and left hand drum on the left hand bottom bracket. Insert rollers into bottom brackets and hinge tubes on bottom section.

NOTE: V erify astragal (bottom seal) is aligned with door section. If there is more than 1/2” excess astragal on either

side, trim off so that astragal is aligned with door section.

IMPORTANT! Right and left hand is always determined from inside the building looking out.

5A-5C

Before installing the bottom section, measure and cut vinyl jamb weather-stripping (may not be included) for entire garage door opening. T emporarily nail the weather-stripping to the door jambs and header . Center the bottom section in the door opening. Level it using wooden shims under the bottom astragal as needed.

6A-6C

Position the first vertical track over the rollers of the bottom section. Make sure the counterbalance cable is located between the rollers and the door jamb. Secure jamb brackets and flagangles to the jamb using 5/16” x 1-5/8” lag screws. Install the other vertical track the same way. Hang cables over flagangles.

IMPORTANT! The tops of the vertical tracks must be level from side to side. If the bottom section was shimmed

to level it. The vertical track on the shimmed side, must be raised the height of the shim.

7A-7C

Place rollers into hinge tubes of second section (lock section). With assistance, lift second section and guide rollers into the vertical tracks. Keep sections aligned and fasten hinges to connect the sections using 1/4-14 x 5/8” self tapping screws. Repeat for other section(s) except top section.

IMPORTANT! Push & hold the hinge leaf against section while securing with 1/4-14 x 5/8 self tapping screws.

NOTE: To install lock (sold separately), see lock instructions included in the lock assembly bag.

To install the L-shaped top brackets, align the top holes in the top bracket base with: a) the second set of holes in the endcap for Model 9100, 9200, and 9600 doors. b) the first set of holes in the endcap for Model 9900 doors.

9900

9600 9200 9100

TorqueMaster™ Installation Instructions Layout

11A

10A

1-11/16” (43mm) TO 1-3/4” (44mm)

LEFT HAND DRUM

11B

12B

DOOR-WIDTH PLUS 3-3/8” (86 mm) TO 3-1/2” (89 mm)

9A 9B

16B

16A

Lift the torque tube and rest on top of flagangles. Orient torque tube so that back of opener is flat against header/spring pad.

12A

13A

14A

Cable drums and torque tube are cam shaped to fit together only one way. To install the cable drum, slide the drum over the winding shaft until the drum seats against the torque tube. The winding shaft must extend past the drum far enough to expose the splines and the groove. Align the winding shaft groove with the round notch in the flagangle. Repeat for opposite side for double spring applications.

For single spring applications, insert the left hand loose winding shaft into the left hand drum prior to sliding the drum over the torque tube.

NOTE: On single spring applications, take care in handling the loose winding shaft (left side) so that it does not slide back

into the torque tube.

14A-14B

Beginning with the right hand side, lubricate entire circumference of the drive gear with the oil provided in the packet. DO NOT SUBSTITUTE OIL. Slide the drive gear onto the winding splines until it touches the flagangles.

NOTE: No drive gear is required for the left side on single spring applications.

RIGHT HAND DRUM

13B

13C

14B

17A

17B

17C

17D

IMPORTANT! Warning tags must be securely attached to both end brackets.

Slide the right hand end bracket over the drive gear. Secure end bracket and the flagangle to the jamb using (2)5/16 x 1-5/8” lag screws.

Beginning with the right side, install the counter gear with the missing tooth toward the outside, away from the end bracket. Press the counter gear onto the end bracket until snaps engage. Select the right hand counter cover assembly and align the hex of the counter cam with the end of the winding shaft. Also, align the “0” on the counter cover with the raised rib on the end bracket. Press the counter cover assembly against the counter gear until it locks into place. Repeat for left hand side for double spring applications.

NOTE: No drive gear, counter gear or counter cover assembly is required on left hand side for single spring applications.

Only an end bracket is needed.

IMPORTANT! At this time do not wind counter balance springs!

16A-16B

Locate the spring pad. The spring pad is a vertical running board directly above the center of the door. Remove (2) 1/420 flange nuts from bottom of opener power head. NOTE: Do not discard flange nuts. Place the support bracket underneath opener power head, to the right side of motor, centered on spring pad. Level the torque tube to the top of the door section with the idrive™ resting on the support bracket. Once torque tube is level, secure support bracket to the spring pad with (2) 1/4 x 2" lag screws. Lift and slide the opener power head over the support bracket, aligning the mounting studs with the bracket slots. Loosely fasten to mounting studs with the (2) 1/4-20 flange nuts. NOTE: Do not tighten 1/4-20 flange nuts to power

head studs at this time.

17A-17D

Attach the loose disconnect cable (located in operator hardware bag) to the opener power head with “S” hook. Close both ends of “S” hook to lock assembly together. Thread the disconnect cable through hole in right hand end bracket and remove all slack between power head and right hand end bracket. Mark location on right door jamb, six feet above the ground to mount disconnect handle. Thread disconnect cable through handle bracket and then handle. Align top of handle bracket with mark on wall. Remove all cable slack between the power head and top of handle bracket.

Insert and tighten #6-20 x 1/2" screw until snug, and then tighten screw 1 to 1-1/2 additional turns to secure cable in handle. Trim off excess cable from bottom of handle.

Holding handle bracket, remove all remaining slack between power head. With slack removed, secure bottom of handle bracket with (1) 1/4 x 1-1/2" lag screw.

Fasten using (4) 1/4-14 x 5/8 self tapping screws. Secure the top bracket slide to the bracket base using (2) 1/4-20 carriage bolts and nuts. Insert rollers into top slide.

9A-9C

Model 9100 and 9200 Foamcore™ doors over 13’ wide require a 3” U-Bar (supplied). Center the U-Bar over the top rib of the top section and secure it to the section using (6) 1/4-20 x 5/8” self drilling screws.

10A-10B

Place top section in the door opening, align with other sections and secure it temporarily by driving a nail into the header near the center of the door and bending it over the section. Now flip up, hold tight against section, and fasten center hinges first, and end hinges last. When installing a door with a T orqueMaster™ counterbalance system, vertical track alignment is critical. Position flagangle between 1-11/16” (43 mm) to 1-3/4” (44 mm) from the edge of the door . Flagangles must be parallel to the door sections. Now complete the vertical track installation on both sides by securing the center jamb bracket and tightening the other lag screws.

IMPORTANT! The dimension between the flagangles must be door-width plus 3-3/8” (86mm) to 3-1/2” (89 mm) for

smooth, safe door operation.

11A-11B

T o install horizontal track, place the curved end over the top roller . Align the key slot in the track with the quick install tabs on the flagangle. Push the curved portion of the horizontal track downward to lock into place, while raising the rear of the horizontal to align the horizontal angle with the flagangle. Level the horizontal track, then bolt the horizontal angle to the flagangle using (1) truss head bolt and nut. Repeat for other side. V ertically align the top section with the lower sections. Once aligned, move top bracket slide out to force top roller against horizontal track. Tighten nuts to secure top bracket slide to top bracket base. Repeat for other side. Remove nail that was temporarily holding top section in place.

IMPORTANT! Failure to remove nail before attempting to raise door could cause permanent damage to top section.

LEFT HAND BOTTOM BRACKET

10B

CAUTION: Pull handle just enough to remove the cable slack. Pulling the cable more could cause the opener power

head to disconnect from the torque tube.

72” (1829 mm)

SET SCREW

Rotate disconnect handle to one side exposing upper mounting hole in handle bracket. Secure handle bracket with a second 1/4 x 1-1/2" lag screw. Apply emergency disconnect label next to the mounted bracket. Use mechanical fasteners if adhesive will not adhere.

Using the emergency disconnect, pull disconnect handle downwards and place it in the manual door operated position. Use disconnect label for reference. Motor will be rotated 90° from its packaged position.

NOTE: If motor does not pivot 90°, see troubleshooting section in the idrive™ main installation manual.

Clamp locking pliers onto both vertical tracks just above third roller. This is to prevent garage door from rising while winding counterbalance springs.

WARNING!

FAILURE TO CLAMP TRACK CAN ALLOW DOOR TO RAISE AND CAUSE SEVERE INJURY OR DEA TH.

Adjust the counter balance cables by rotating the drum until the set screw faces directly away from the header. Loosen the set screw no more than 1/2 turn. Pull on the end of the cable to remove all cable slack. Check to ensure the cable is aligned and seated in the first groove of the cable drum. Snug the set screw, then tighten an additional 1-1/2 turns. Cut off excess cable.

IMPORTANT! DO NOT USE IMPACT GUN TO WIND SPRING(S)

WARNING!

DO NOT RAISE DOOR UNTIL HORIZONTAL TRACKS ARE SECURED AT REAR AS OUTLINED IN STEP 21, OR DOOR COULD FALL FROM OVERHEAD POSITION CAUSING SEVERE INJURY OR DEATH.

12A-12B idrive™ Installation

NOTE: For non-idrive™ operated garage doors see Alternative Installations on the reverse side of this manual.

Lay the torque tube on the floor (inside garage) in front of the door with the labeled end to the left. NOTE: Opener will not slide over a torque tube label. Attempting to slide opener over the left end of the torque tube can damage the internal electronics.

NOTE: Hold opener by the main body. Do NOT hold by the motor.

Look into the opener’s left side to ensure the left hand bearing and the internal (black) sleeve are aligned with the torque tube profile. Once aligned, slide the opener power head onto the right hand end of the torque tube. As the right end of the torque tube enters the internal (black) sleeve, rotate the opener back and forth slightly to help aid alignment.

NOTE: Do not force the opener onto the torque tube if misalignment occurs.

Continue sliding the opener power head onto the torque tube. Align the right hand bearing with the torque tube and slide the opener power head completely onto the torque tube until the torque tube exits the opener power head’s right hand bearing. Continue sliding the opener power head to the center of the torque tube and plug the motor power cord into the opener power head.

IMPORTANT! Right and left hand are always determined from inside the garage looking out.

Beginning with the right hand side. Press and hold in the canoe clip. Ensure the cable is in the first groove of the drum.

CANOE CLIP

Using an electric drill (high torque gear reduced to 1300 RPM preferred) with a 7/16" socket, carefully rotate right hand winding bolt clockwise, until counter shows 2-3 turns. This will keep the counterbalance cable taut while adjusting the left hand side counterbalance cable. Repeat step 18 and 19 for left side. NOTE: Single spring applications require no spring winding.

Ensure counterbalance cable tension is equal for both sides prior to fully winding spring(s) to appropriate number of turns.

Carefully rotate the winding bolt head clockwise until the counter show the correct number of turns for your door. See the Spring T urn chart on the reverse side of this manual. Repeat for the opposite side on double spring T orqueMaster™ systems. If door raises off of floor remove 1/2 - 1 full turn from each spring before proceeding.

After spring is wound, hold the lock nut (in back of end bracket) stationary with a 7/16” wrench while rotating the winding bolt clockwise until snug. Tightening of the lock nut prevents spring from unwinding. Repeat for opposite side if necessary.

IMPORTANT! Adjustments to the recommended number of turns may be required. AFTER REAR SUPPORT

ASSEMBLY IS COMPLETE, check door balance. If door raises off of floor under spring tension alone, then reduce turns until door will rest on floor. A “hot” door such as this can cause idrive™ operation problems.

CONTINUE INSTALLA TION INSTRUCTIONS ON REVERSE SIDE.

Jamb Bracket Schedule

ROOD

THGIEH

"0'6

KCART"46

)mm6261(

"5'6

KCART"96

)mm3571(

"6'6

KCART"07

)mm8771(

"8'6

KCART"27

)mm9281(

"0'7

KCART"67

)mm0391(

"3'7

KCART"97

)mm7002(

"6'7

KCART"28

)mm3802(

"9'7

KCART"58

)mm9512(

"0'8

KCART"88

)mm5322(

"0'8

KCART"88

)5322(

NOTE: Jamb brackets are stamped for identification.

1/4”-20 Flanged

Hex Nut #100279

SNOITCES4

SNOITCES5

1-LT2-LT3-LT

MOTTOB

ELOH

ELDDIM

ELOH

ELDDIM

ELOH

MOTTOB

ELOH

ELDDIM

ELOH

MOTTOB

ELOH

ELDDIM

ELOH

ELDDIM

ELOH

ELDDIM

ELOH

POT

ELOH

MOTTOB

ELOH

MOTTOB

ELOH

MOTTOB

ELOH

MOTTOB

ELOH

MOTTOB

ELOH

MOTTOB

ELOH

ELDDIM

ELOH

ELDDIM

ELOH

ELDDIM

ELOH

POT

ELOH

1/4”-20 x 5/8”

Carriage Bolt #262617

A/N

MOTTOB

ELOH

ELDDIM

ELOH

ELDDIM

ELOH

ELDDIM

ELOH

ELDDIM

ELOH

TL-3

HOLES

TL-2

HOLES

TL-1

HOLES

1/4”-20 x 11/16” Self Drilling Screw

#300723

(1) 7/16” Hex Head Driver

(1) 7/16” Drill Bit (Step Plate)

Gloves

(1) Step Ladder

(1) Level (2’ Minimum Length)

(1) Pliers

5/16” x 1-5/8” Hex Head Lag Screw

#100292

(1) Electric Drill with Clutch

(50) 1-1/2” Common Nail

(1) Tape Measure

Required Tools

(1) 7/16” Wrench

(1) Hammer

(1) Screw Driver (Standard Blade)

(2 or 3) Saw Horses or other supports for placing sections on while assembling

(2) Locking Pliers

(1) Screw Driver (Phillips Blade)

Safety Glasses

(1) Socket Wrench with 7/16”, 1/2”, 9/16” sockets

1/4” x 2” Slotted Hex Head Lag Screw

#284454

IMPORTANT

SAFETY NOTICES

Wayne-Dalton Corp.

P.O. Box 67

Mt. Hope, Ohio 44660

Read these instructions carefully before attempting installation. If in question about any of the procedures, do not perform the work. Instead, have a qualified door agency do the installation or repairs.

1. Wear protective gloves during installation to avoid possible cuts from sharp metal edges.

2. It is always recommended to wear eye protection when using tools, otherwise serious eye injury could result.

3. Avoid installing your new door on windy days. Door could fall during the installation and cause damage and personal injury .

4. If the door is to be electrically operated at any time, all pull ropes MUST be removed to prevent injury or death to children who may become entangled in the rope. The locking mechanism MUST also be disengaged.

5. Operate door ONLY when properly adjusted and free of obstructions.

6. Should the door become hard to operate or completely inoperative, a qualified door agency should correct the problem to prevent damage to the door or serious personal injury .

7. DO NOT PERMIT children to play with the garage door or the electrical controls. Fatal injury could result, should the child become entrapped between the door and the floor.

8. To prevent serious injury or death, avoid standing in the open doorway or walking through the doorway while the door is moving.

9. Door is constantly under EXTREME SPRING TENSION. To prevent possible serious injury or death, adjustments, repairs, removal or installation, ESPECIALL Y of SPRING ASSEMBLIES, CABLES or BOTTOM CORNER BRACKETS, should be performed ONLY by qualified door service people.

10. If your existing garage door opener does not have a reversing mechanism, you should consider purchasing one that has up to date safety features. These features can prevent opener related property damage or personal injury .

11. Check all bolted connections monthly during the lifetime of the door to prevent damage or personal injury caused by loose connections.

MAINTENANCE AND PAINTING

INSTRUCTION FOR

PRE-PAINTED STEEL DOORS

MAINTENANCE

While factory-applied finishes for steel garage doors are so durable that they will last many years longer than ordinary paints, it is desirable to clean them thoroughly on a routine basis. Apparent discoloration of the paint may occur when it has been exposed in dirt-laden atmospheres for long periods of time. Slight chalking may also cause some change in appearance in areas of strong sunlight. A good cleaning will generally restore the appearance of these coatings and render repainting unnecessary. An occasional light cleaning will also help maintain an aesthetically pleasing appearance. To maintain the original finish of the garage doors, the only regular maintenance necessary is that of annual washing. Mild solutions of detergents or household ammonia will aid in the removal of most dirt, and the following are recommended levels: One cup of Tide™, or other common detergents, which contain less than 0.5% phosphate, dissolved into five gallons of warm water. NOTE: The use of detergents containing greater than 0.5% phosphate is not recommended for use in general cleaning of garage doors.

Wax on the surface must be removed or paint peeling/flaking will result. To remove this wax, it will be necessary to lightly scuff the surface with a gray (not green!) 3M ScotchBrite pad saturated with soapy water. A final wipe and rinse should be done with clean water only, to remove any loose dust or soap film. Surface scratches, which have not exposed the metal substrate, can be lightly buffed or sanded with 0000 steel wool or No. 400 sand paper to create a smoother surface. Care must be taken to not expose the substrate under the paint (see Note No. 2). Once this exposed condition exists, the likelihood for rusting is greatly increased. See the following paragraph if the metal substrate is observed. Exposed substrate must be treated to prevent rust from forming (see Note No. 2). Sand the exposed area lightly and paint with high quality metal primer to protect from corrosion. Follow drying time on primer can label before applying topcoat. The surface to be re-coated must not be to smooth or the repaint material will not adhere to it (see Note No. 2). It is advisable to test a representative area to evaluate adhesion. If poor adhesion is observed, the surface must be abraded by sanding or buffing using grades mentioned above. Care must be taken to not expose the substrate under the paint.

After the surface has been properly prepared it must be allowed to dry thoroughly, then coated immediately with a premium quality latex house paint. Follow the paint label directions explicitly. Oil base paint is not recommended. Please note that if substrate is exposed, painting with latex paint may cause accelerated rusting of steel.

NOTES:

1. Repainting of finish painted steel doors cannot be warranted as this condition is totally beyond door

manufacturer’s control.

2. If the steel door surface has a finish painted textured surface representing wood grain, stucco, etc., this step

should not be attempted as danger of exposing substrate is greatly increased.

3. Consult a professional coatings contractor if in doubt about any of the above directions.

4. Follow directions explicitly on the paint and solvent container labels for proper applications of coatings and disposal of containers. Pay particular attention to those directions involving acceptable conditions in which to paint.

CAUTION: NEVER MIX CLEANSERS OR DETERGENTS WITH BLEACH.

SURFACE PREP ARA TION FOR P AINTING

P AINTING

Rev.1 10/02

plied if not necessary.

NOTE: Depending on the door model, some parts listed will not be sup-

(X) REAR SUPPORT SOLD SEP ARA TEL Y (W) idrive™ OPERATOR SOLD SEPARA TEL Y (V) 36 TOOTH WORM GEAR # 282335 COUNTER COVER ASM. (LH) (DOUBLE SPRING) # 287721 (U) COUNTER COVER ASM. (RH) # 287722 (T) COUNTER GEAR # 284035 (S) LOOSE WINDING SHAFT (SINGLE SPRING) # 280066 (R) END BRACKET (RH) # 282340 (Q) END BRACKET (LH) # 282937 (P) CABLE /DRUM ASM. (PAIR) # 280086 (O) TORQUEMASTER TUBE 1 ASSEMBLY

NOTE: See TorqueMaster™ with idrive™ Parts List

TORQUEMASTER™ COUNTERBALANCE SYSTEM

(N) 80” HORIZ. ANGLE (LEFT) # 292538 (M) 80” HORIZ. ANGLE (RIGHT) # 292539 (L) 21-15/16” HORIZ. ANGLE # 292536 (K) R 15” FLAGANGLE (RIGHT, 19-7/8”) # 240383 (J) R 15” FLAGANGLE (LEFT, 19-7/8”) # 240382 (I) R 12” FLAGANGLE (RIGHT, 18-1/2”) # 292531 (H) R 12” FLAGANGLE (LEFT, 18-1/2”) # 292530 (G) HORIZONTAL TRACK 1 PAIR (F) TL-3 JAMB BRACKET # 261967 (E) TL-2 JAMB BRACKET # 261966 (D) TL-1 JAMB BRACKET # 261965 (C) VERTICAL TRACK 1 PAIR (B) ROLLER #154489 (A2) TOP BRACKET SLIDE # 158046 (A1) TOP BRACKET BASE # 158044

Parts List

PART NO. 302868

(Z2) 60” PULL ROPE # 274884 (Z1) # 6 SCREW EYE # 100362 (Y) CENTER BRACKET ASM. # 296246

Alternate Parts List

3/8”-16 Hex Nut

#100313

3/8”-16 x 3/4” Truss Head Bolt

#154531

1/4”-14 x 5/8” Self Tapping

Screw #236565

...CONTINUED INSTALLATION INSTRUCTIONS

Locate right hand drum wrap. Slide back half of the drum wrap behind drum placing the right end wall between the drum and flagangle. Close front half of the drum wrap around drum, engage inboard snap and press firmly until a distinct snap is felt. Outboard catch must be engaged as shown. Confirm both snap and catch are fully engaged by lightly tugging against them. Repeat for the left side.

Hold the door down to prevent it from rising unexpectedly in the event the spring was overwound and carefully remove the locking pliers from the vertical tracks. Raise the door until the top section and half of the next section are in a horizontal position. Do not raise door any further since rear of horizontal track is not yet supported.

WARNING!

RAISING DOOR FURTHER CAN RESULT IN DOOR F ALLING AND CAUSE SEVERE INJUR Y OR DEA TH.

Now clamp a pair of locking pliers to the vertical tracks just above the second roller on one side, and just below the second roller on the other side. This will prevent the door from raising or lowering while installing the rear support. Using perforated angle, 2” lag screws and 5/16 bolts with nuts (may not be supplied), fabricate rear support for horizontal tracks. Attach horizontal tracks to the rear supports with 5/16-18 x 1-1/4” hex bolts and nuts (may not be supplied). Horizontal tracks must be level and parallel with door.

WARNING!

KEEP HORIZONT AL TRACK P ARALLEL AND WITHIN 3/4” OF DOOR EDGE, OTHER WISE DOOR COULD FALL, RESULTING IN SERIOUS INJUR Y OR DEATH.

Permanently attach the vinyl weather stripping to both door jambs and the header. Avoid pushing vinyl into force of door. Now, lift the door and check it’s balance. Adjust, if door lifts by itself (also hard to pull down) or if door is difficult to lift (too easy to pull down). Anytime spring adjustments are made you must loosen the lock nuts to begin with and retighten both lock nuts afterwards. T o adjust spring(s), only add or remove 1/4 turn on the counter reading at a time. Adjust both sides equally.

IMPORTANT! Do not add or remove more than 1 spring turn from specified amount.

If the door still does not operate easily, lower the door into the closed position, UNWIND SPRING(S) TO ZERO, and recheck the following items:

1.) Check the door for level.

2.) Check the T orqueMaster™ tube and flagangles for level and plumb.

3.) Check the distance between the flagangles - must be door width plus 3-3/8” to 3-1/2”.

4.) Check the counterbalance cables for equal tension - loosen set screws and adjust if necessary.

5.) Rewind the spring(s).

6.) Make sure door isn’t rubbing on jambs.

NOTE: As a safety feature, the right hand end bracket cannot be disassembled for service until the spring is completely

unwound and the counter cover reads zero.

After door installation is completed, refer to the idrive™ owner’s manual, starting at the PRE-OPERA TION INST ALLA- TION section to complete the opener installation.

1/4” x 1-1/2” Slotted Hex Head

Lag Screw #269025

#6-20 x 1/2” Plastifast

(Disconnect Handle) #296940

AL TERNA TIVE INST ALLA TIONS

12A

If you are not installing the idrive™ operator on your garage door, you must install the center bracket bushing assembly. Follow these instructions for a non-idrive™ operated garage doors. TorqueMaster™ springs come lubricated and pre-assembled inside the torque tube. To install, lay the torque tube on the floor in front of the door with the labeled end to the left. Slide the center bracket/bushing assembly onto the torque tube, from the right hand side, toward the center. Shake the T orqueMaster™ tube gently to extend the winding shafts out about 5” on both ends. Single spring T orqueMaster will only have the right hand spring. Slide center bracket/bushing assembly from the right side to the center of the torque tube.

IMPORTANT! Right and left hand are always determined from inside the

building looking out.

12B

When installing a DoorMaster™ operator replace the bushing with the drive gear (located in DoorMaster™ package).

To locate the center bracket, mark the header halfway between the flagangles and level the TorqueMaster tube. Fasten the metal bracket to the header using (2) 1/4 x 1-1/2” lag screws.

STEP PLATES OPTIONAL ACCESSORY

Make one mark 1” (25 mm) up from the center of bottom edge and another mark 2- 3/16” (56 mm) up from the first mark. Drill a 7/16” (11 mm) hole through the section at each mark and insert the outside step plate. Loosely fasten step plate slide to base with (1) 1/4-20 x 5/8” carriage bolt and nut. Align inside step plate holes and fasten from inside using the #8 screws provided. Install one #8 x 3/ 4” screw in the bottom step plate hole. The screw in the top hole varies with door models. Use the screw size required for your model door. a) #8 x 3/4” screw for Model 9100 and 9200 b) #8 x 1” screw Model 9600 c) #8 x 1-1/2” screw Model 9900

Tighten 1/4-20 carriage bolt and nut.

PULL ROPE

Screw the No. 6 screw eye into the wood jamb approximately 48” to 50” (1220 to 1270 mm) from the floor. Tie the pull rope to the screw eye and to the bottom bracket as shown.

WARNING!

DO NOT INST ALL PULL ROPES ON DOORS WITH ELECTRIC OPERATORS. CHILDREN MAY BECOME ENT ANGLED IN THE ROPE CAUSING INJUR Y OR DEA TH.

12A

12B

12. Definition of key words used in this manual:

WARNING! -- Indicates a potentially hazardous situation which, if not avoided, could result

in serious injury or death.

IMPORTANT! -- Required step for safe and proper door operation.

NOTE: -- Information assuring proper installation of the door.

TYPICAL TROLLEY OPERATOR INSTALLATION

If you are installing an electric operator on your door, the following information is provided to ensure proper function of your door/operator installation. Figure below shows a typical means of connecting the operator arm to the operator stile located in the center of the top section.

Wayne-Dalton Corp.

TYPICAL OPERATOR

BRACKET (SUPPLIED

WITH OPERATOR)

BRIDGE POINT

SCREWS (SUPPLIED WITH OPERATOR)

SEE OPERATOR INSTRUCTIONS FOR DETAILS ON INSTALLATION

INSTALLA TION TIPS:

1. Follow the installation instructions supplied with your operator.

2. Reinforce top section per manufacturer’s recommendation prior to attaching

operator. See illustration below.

3. Install trolley rail 1/2” to 1-1/2” (13 - 38 mm) above high arc of top section of the door.

4. Mount operator to ceiling so that 1” to 1-1/2” (25 - 38 mm) clearance is maintained between trolley rail and top section when door is fully open (trolley rail will slope down towards rear).

5. The operator bracket must be mounted to the operator stile on the top section so it bridges the transition point in section thickness.

6. Attach operator rail to spring pad.

7. Attach operator to ceiling using perforated angle.

8. IMPORTANT! Angle must be attached to framing member(s).

TYPICAL OPERATOR ARM (SUPPLIED WITH OPERATOR)

OPERATOR STILE

WARNING!

OPERAT OR MUST BE TESTED A T TIME OF INST ALLA TION AND MONTHL Y THEREAFTER TO ENSURE THA T DOOR REVERSES ON CONT ACT WITH 2 X 4 BOARD LAID FLA T UNDER THE DOOR. FAILURE TO ADJUST OPERATOR, IF NECESSARY, CAN RESULT IN SEVERE INJURY OR DEATH. IF YOUR OPERAT OR IS EQUIPPED WITH PHOTOELECTRIC SYSTEM, THEN THIS MUST BE TESTED A T THE SAME TIME TO ENSURE THA T DOOR DOES NOT CLOSE AND A CLOSING DOOR OPENS IF SYSTEM IS OBSTRUCTED. FAILURE TO MAKE ADJUSTMENTS, IF NECESSAR Y, CAN RESUL T IN SEVERE INJURY OR DEA TH.

P.O. Box 67, Mt. Hope, Ohio

www.wayne-dalton.com

The Manufacturer warrants the 9900 THERMOWAYNE, 9600 THERMOGARD and 9200 FOAMCORE insulated garage door for as long as you own the door from the time of installation against structural failure (rendering the door inoperable) of the door sections due to separation/ degradation of foam insulation. Other conditions and exceptions as contained herein apply.

The Manufacturer warrants the steel skin of the 9900 THERMOWAYNE, 9600 THERMOGARD and 9200 FOAMCORE insulated garage door for as long as you own the door from the time of installation against deterioration such as cracking or splitting due to rust-through. Other conditions and exceptions contained herein apply.

The Manufacturer warrants the garage door hardware and track, excluding springs, for as long as you own the door against defects in workmanship or material from time of installation.

After a period of TWENTY YEARS from time of installation, replacement of LIFETIME LIMITED WARRANTY materials are prorated at 50 percent of Manufacturer’s published pricing at time of claim.

This warranty extends only to the original homeowner, providing the door is installed in his/her place of primary residence. It is not transferable. The warranty applies to residential property only and is not valid on commercial or rental property.

The Manufacturer warrants that any parts of the door not covered by the above limited warranty will be free from defects in workmanship and material for ONE YEAR from the time of installation.

The Manufacturer shall, upon notification, correct any nonconformity at its option, by repairing, replacing, or refunding original purchase price of any defective part(s). This warranty covers material only and excludes all other charges incurred.

NO EMPLOYEE, DISTRIBUTOR, OR REPRESENTATIVE IS AUTHORIZED TO CHANGE THE FOREGOING WARRANTIES IN ANY WAY OR GRANT ANY OTHER WARRANTY ON BEHALF OF MANUFACTURER.

The Manufacturer shall not be responsible for any damage resulting to or caused by its products by reason of installation, improper storage, unauthorized service, alteration of products, neglect or abuse, or attempt to use the products for other than the customary usage or for their intended purposes. The 9900 THERMOWAYNE, 9600 THERMOGARD and 9200 FOAMCORE warranty becomes null and void if the door is punctured with any hole or if a hole is drilled into the door sections other than those specified in the notes of installation. This warranty does not cover the product due to circumstances such as normal wear, damage from corrosive fumes or substances, fire, condensation, vandalism, acts of God, or other causes beyond Manufacturer’s control, nor replacement or repair labor.

THIS WARRANTY COVERS A CONSUMER PRODUCT AS DEFINED BY THE MAGNUSON-MOSS WARRANTY ACT. NO WARRANTIES, EXPRESSED OR IMPLIED, (INCLUDING, BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), SHALL EXTEND BEYOND THE APPLICABLE TIME PERIOD STATED IN BOLD FACE TYPE ABOVE.

Claims for defects in material and workmanship covered by this warranty shall be made in writing to the dealer from whom the product was purchased within the warranty period. Manufacturer may either send a service representative or have the product returned to the Manufacturer at Buyer’s expense for inspection. If judged by Manufacturer to be defective in material or workmanship, the product will be replaced or repaired at the option of Manufacturer, free from all charges except authorized transportation and replacement labor.

THE REMEDIES OF BUYER SET FORTH HEREIN ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER REMEDIES. THE LIABILITY OF MANUFACTURER, WHETHER IN CONTRACT, TORT, UNDER ANY WARRANTY, OR OTHERWISE, SHALL NOT EXTEND BEYOND ITS OBLIGATION TO REPAIR OR REPLACE, AT ITS OPTION, ANY PRODUCT OR PART FOUND BY MANUFACTURER TO BE DEFECTIVE IN MATERIAL OR WORKMANSHIP. MANUFACTURER SHALL NOT BE LIABLE FOR COST OF REMOVAL OR INSTALLATION OR SHALL NOT BE RESPONSIBLE FOR ANY DIRECT, INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE.

This warranty gives you specific legal rights, and you may also have other rights, which may vary from state to state. However, some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.

44660

DÉCOR LITES ACR YLIC GLAZING CLEANING INSTRUCTIONS:

1. To clean acrylic glazing wash with plenty of nonabrasive soap or detergent and water. Use the bare hand to feel and dislodge any caked dirt or mud. A soft, grit-free cloth, sponge or chamois may be used to wipe the surface. Do not use hard or rough cloth that will scratch the acrylic glazing. Dry with a clean damp chamois.

2. Grease and oil may be removed with kerosene or a good grade of naphtha (No aromatic content.). Users of these solvents should become familiar with their properties to handle them safely.

3. Do not use: Window cleaning fluids, scouring compounds, gritty cloths, leaded or ethyl gasolines, or solvents such as alcohol, acetone, carbon tetrachloride, etc.

9900 Thermowayne™ 9600 Thermogard

9100/9200 Foamcore™

LIFETIME LIMITED WARRANTY

www .wayne-dalton.com

Installation Instructions and Owners Manual

TorqueMaster™ - Single Spring and Double Spring

9100/9200 Foamcore™ 9600 Thermogard® 9900 Thermowayne™

TorqueMaster™ with idrive™

Parts List

(O) TORQUEMASTER TUBE 1 ASSEMBLY (P) CABLE /DRUM ASM. (P AIR) # 2800 86 (Q) END BRACKET (LH) # 282937 (R) END BRACKET (RH) # 282340 (S) LOOSE WINDING SHAFT (SINGLE SPRING) # 2800 66 (T) COUNTER GEAR # 284035 (U) COUNTER COVER ASM. (RH) # 287722

Spring Turns

Door Height = Spring T urns

6’0” = 14 turns 6’-3” = 14-1/2 turns 6’-5” = 15 turns 6’-6” = 15 turns 6’-8” = 15-1/2 turns 6’-9” = 15-1/2 turns 7’-0” = 16 turns 7’-3” = 16-1/2 turns 7’-6” = 17 turns 7’-9” = 17-1/2 turns 8’-0” = 18 turns

COUNTER COVER ASM. (LH) (DOUBLE SPRING) # 287 721 (V) 36 TOOTH WORM GEAR # 2823 55 (W) idrive™ OPERATOR SOLD SEP ARATEL Y (Y) CENTER BRACKET ASM. (NON-idrive™ OPERA TED) # 296246

NOTE: See idrive™ Main Installation and Owners Manual for idrive™ parts

NOTE: Single Spring TorqueMaster™ shown in illustration.