Waring Pro MX1000RXT User Manual [en, es, fr]
HALF GALLON HI-POWER BLENDER
LICUADORA DE ALTA VELOCIDAD DE 1.9L
MÉLANGEUR HAUTE PUISSANCE DE 1,9L
MX1000R
For your safety and continued enjoyment of this product,
always read the instruction book carefully before using.
Para su seguridad y para disfrutar plenamente de este producto,
siempre lea las instrucciones cuidadosamente antes de usarlo.
An que cet appareil vous procure en toute sécurité beaucoup de satisfaction,
lire attentivement le mode d’emploi avant de l’utiliser.
IMPORTANT UNPACKING
INSTRUCTIONS
1. Place the box containing your Waring Pro® blender on a at
sturdy surface before unpacking.
2. Open corrugated aps.
3. Remove instruction book and any printed materials from top
of box.
4. Pull up corrugation and remove. Remove jar and padding.
CAUTION: Sharp blade inside blender jar.
5. Remove corrugated insert. Remove blender base from box
and set aside.
6. Replace all corrugated inserts in the gift box and save the
box for repacking.
REPACKING INSTRUCTIONS
1. Place blender on a large, sturdy at surface.
2. Carefully place blender base in bottom of box.
3. Place long corrugated insert over base.
4. Insert blender jar and padding.
5. Close and seal box for shipping.
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should
always be followed including the following:
in any manner. Return appliance to the nearest authorized
service facility for examination, repair, or electrical or mechanical
adjustment.
8. The use of attachments including canning jars not recommended
by the appliance manufacturer may cause hazards.
9. Do not use outdoors.
10. Do not let cord hang over edge of table or counter, or touch hot
surfaces.
11. Keep hands and utensils out of container while blending, to
prevent the possibility of severe personal injury and/or damage
to the blender. A rubber scraper may be used, but must be used
only when the blender is not running.
12. Blades are sharp. Handle carefully.
13. Always operate blender with lid in place.
14. When blending hot liquids, remove center piece of two-piece lid.
See Hot Blending instructions.
15. The use of ear protection is recommended during extended
operating periods.
16. See Cleaning and Sanitizing instructions for all Waring Pro
Blenders. NOT FOR WATERJET CLEANING.
17. Do not operate your appliance in an appliance garage or under a
wall cabinet. When storing in an appliance garage, always unplug
the unit from the electrical outlet. Not doing so could create a
risk of re, especially if the appliance touches the walls of the
garage or the door touches the unit as it closes.
®
SAVE THESE INSTRUCTIONS
1.
READ ALL INSTRUCTIONS BEFORE USING.
2. Unplug from outlet when not in use, before putting on or
taking off parts, and before cleaning.
3. To protect against electrical hazards, do not immerse the
blender base in water or other liquid.
4. Do not use carbonated liquids in the blender jar, or any
blending container. Using carbonated liquids in the
blender jar or any blending container may result in injury.
5. Close supervision is necessary when any appliance is used by
or near children.
6. Avoid coming into contact with moving parts.
7. Do not operate any appliance with a damaged cord or plug
or after the appliance malfunctions or is dropped or damaged
2
MX1000R (Model: MXMPBKP6) BLENDER SPECIFICATIONS
• Capacity: 64 oz. working capacity
• Switch Settings: (2 Speeds) Hi Low Pulse
• Speed (RPMs) 30,000 26,000 30,000
• Rating: 120 Volts - 12.0 Amps
• Base Material: Polycarbonate
• Bearing: High Precision Ball Bearing
• Cord: 6-Foot Three-Conductor Ground Cord With
Strain Relief in Base
• Overall Height: 19 inches
• Weight: 15 lbs.
• cETLus, NSF listed
• Operating Cycle: 1 min. ON/3 min. OFF
3
GROUNDING INSTRUCTIONS
• For your protection, this appliance is equipped with a
3-conductor cord set.
• 120 Volt units are supplied with a molded 3-prong groundingtype plug (NEMA 5-15P) and should be used in combination
with a properly connected grounding type outlet as shown in
Figure A.
If a grounding type outlet is not available, an adapter, as shown in
Figure B, may be utilized to enable a 2-slot wall outlet to be used
with a 3-prong plug (except in Canada and Europe). As shown in
Figure C, the adapter must be grounded by attaching its grounding
lug under the screw of the outlet cover plate.
Caution: Before using an adapter, you must be sure that the outlet
cover plate screw is properly grounded. If in doubt, consult a
licensed electrician.
Never use an adapter unless you are sure it is properly grounded.
Note: Use of an adapter is not permitted in Canada and Europe.
Green/Yellow: Earth/Ground. Blue: Neutral. Brown: Live.
Note: User-installed cord set plugs are not permitted in Europe.
This appliance is for 120 Volts only and should not be used with a
converter.
MX1000R (Model: MXMPBKP6) OPERATION
1. Before starting, make sure that the
blender is unplugged.
2. With the unit in OFF position, place
container on blender base. Be sure
container is fully seated and that drive
coupling is properly engaged. Plug
blender cord into outlet.
3. Put ingredients into container and
cover it. Do not ll above MAX line.
4
4. CAUTION: DO NOT use carbonated liquids in the blender
jar or any blending container. Using carbonated liquids
in the blender jar or any blending container may result in
injury.
5. This blender has 2 speed settings: HI and LOW. Press paddle
switch to desired position. To crush ice quickly, use HI speed
setting.
6. When nished blending, set paddle switch to OFF position.
7. This blender is equipped with a pulse option. Hold paddle
switch in the lower position to engage PULSE function. Unit
will run on HI speed until the paddle switch is released.
8. Allow motor to come to a complete stop before removing
container from blender base. Never place the container on the
motor base or remove it from the motor base while motor is
running.
9. Always hold container with one hand when starting and while
blending. Never operate without jar lid.
10. Wash and dry container after each use. See Cleaning and
Sanitizing instructions.
IMPORTANT
HOT BLENDING INSTRUCTIONS
To minimize the possibility of being scalded when blending hot
materials, the following precautions and procedure must be
observed.
• Hot materials are those that are 100°F (38°C) or hotter.
• Limit the amount of materials processed to 1 pint.
• Completely remove the center portion of the two-piece
container lid before starting motor (this will allow venting of
the rapidly heated and expanding
air inside the container when blender is running).
• Always start blending on lowest speed setting, and then
progress to desired speed.
• Never stand directly over blender when it is being started or
while it is running.
5
CLEANING AND SANITIZING INSTRUCTIONS
THE CONTAINER MUST BE CLEANED AND DRIED AFTER EACH
USE OF THE BLENDER ACCORDING TO THE FOLLOWING
INSTRUCTIONS. FAILURE TO DO SO MAY ALLOW RESIDUES OF
PROCESSED MATERIAL TO COLLECT ON THE INTERNAL SEALS
OF THE BLADE ASSEMBLY, RENDERING THEM INEFFECTIVE.
• Wash, rinse, sanitize and dry container prior to initial use and
whenever it will not be used again within a period of 1 hour.
• Wash and rinse container after each use.
• Clean and sanitize motor base prior to initial use and after
each use.
• Washing solutions based on non-sudsing detergents and
chlorine-based sanitizing solutions having a minimum chlorine
concentration of 100 PPM are recommended.
The following washing, rinsing, and sanitizing solutions, or their
equivalents, may be used.
SOLUTION PRODUCT DILUTION IN WATER TEMPERATURE
Washing Diversy Wyandotte 4 Tablespoons Hot 115˚F ( 46˚C )
*Diversol® BX/a or CX/A /Gallon
Rinsing Plain Water Warm 95˚F (35˚C)
Sanitizing **Clorox® 1 Tablespoon/Gallon Cold 50-70˚F
Institutional Bleach ( 10-21˚C)
*Diversol® is a registered trademark owned by the Diversey Wyandotte Corp.
**Clorox
• In repetitive batch-processing applications, frequent cleaning
• Do not use container to store processed foods or beverages.
To wash and rinse container:
1. REMOVE CONTAINER FROM MOTOR BASE. Remove lid.
®
is a registered trademark owned by the Clorox Company.
of the container will prolong the life of the blade assembly.
In no case should actual running time between cleanings
exceed ½ hour.
Rinse container interior and lid under running water. Add
washing solution to container. Scrub and ush out the
container interior and lid to dislodge and remove as much
food residue as possible. Empty container.
6
2. Wipe down exterior of container with a soft cloth or sponge
dampened with washing solution. Wash lid and lid insert in
fresh washing solution. Fill container ¼ full with fresh washing
solution, cover (with lid only but without center piece), place on
motor base and run on HI for two (2) minutes. Empty container.
3. Repeat step (2) using clean rinse water in place of washing
solution.
IMPORTANT
NOTE: IN ORDER TO MINIMIZE POSSIBILITY OF SCALDING,
TEMPERATURE OF WASHING SOLUTION AND RINSE WATER
MUST NOT EXCEED 115˚F (46˚C), AND QUANTITY USED MUST
NOT EXCEED ¼-CONTAINER FULL.
IF HIGHER TEMPERATURES OR LARGER QUANTITIES ARE
USED, OBSERVE ALL PRECAUTIONS GIVEN IN THE OPERATING
MANUAL UNDER “HOT BLENDING INSTRUCTIONS.”
To sanitize and dry container:
1. Wipe down exterior of container with a soft cloth or sponge
dampened with sanitizing solution.
2. Fill container with sanitizing solution, cover, place on motor
base, and run on high speed for two (2) minutes. Empty
container. Dislodge any residual moisture from blade assembly
by placing empty container on motor base and running on high
speed for two (2) seconds.
3. Sanitize lid and lid insert by immersing in sanitizing solution for
two (2) minutes.
4. Do not rinse container, lid, or lid insert after sanitizing is
completed. Allow parts to air-dry.
To clean and sanitize motor base:
1. UNPLUG POWER CORD. Wipe down exterior surfaces of
motor base with soft cloths or sponges dampened with
washing solution, rinse water, and sanitizing solution. Prevent
liquid from running into motor base by wringing all excess
moisture from cloths or sponges before using them.
DO NOT IMMERSE MOTOR BASE IN WASHING SOLUTION, RINSE
WATER OR SANITIZING SOLUTION.
2. Allow motor base to air-dry before using.
Any other servicing should be performed by an authorized service
representative.
7
Loading...