PROTEC
B_04259
IceBreaker Piston Pumps
Flow Rate 150 cm3 – 300 cm
3
Version 05/2015
Translation of the Original
Operating Manual
3
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
Table of Contents
1 ABOUT THESE INSTRUCTIONS 6
1.1 Preface 6
1.2 Warnings, Notices and Symbols in these Instructions 6
1.3 Languages 7
1.3.1 Operating Manuals for the Individual Components 7
1.4 Abbreviations in the Text 7
1.5 Terminology for the Purpose of this Manual 8
2 CORRECT USE 9
2.1 Device Types 9
2.2 Type of Use 9
2.3 Use in an Explosion Hazard Area 9
2.4 Safety Parameters 9
2.5 Processible Working Materials 10
2.6 Recommended Application Areas 10
2.7 Reasonably Foreseeable Misuse 11
2.8 Residual Risks 11
3 IDENTIFICATION 12
3.1 Explosion Protection Identi cation 12
3.2 Identi cation X 12
3.3 Type Plate 13
4 GENERAL SAFETY INSTRUCTIONS 14
4.1 Safety Instructions for the Operator 14
4.1.1 Electrical Equipment 14
4.1.2 Personnel Quali cations 14
4.1.3 Safe Work Environment 14
4.2 Safety Instructions for Sta 15
4.2.1 Safe Handling of WAGNER Spray Devices 15
4.2.2 Grounding the Device 16
4.2.3 Product Hoses 16
4.2.4 Cleaning and Flushing 17
4.2.5 Handling Hazardous Liquids, Varnishes and Paints 18
4.2.6 Touching Hot Surfaces 18
5 DESCRIPTION 19
5.1 Design 19
5.2 Mode of Operation 19
5.3 Protective and Monitoring Equipment 20
5.4 Scope of Delivery 20
4
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
Table of Contents
5.5 Data 21
5.5.1 Materials of Paint-wetted Parts 21
5.5.2 Recommended Packings 21
5.5.3 Technical Data 21
5.5.3.1 Technical Data for Jaguar and PROTEC 22
5.5.3.2 Measurements and Connections for Jaguar and PROTEC 23
5.5.3.3 Technical Data for Tiger 24
5.5.3.4 Measurements and Connections for Tiger 25
5.5.4 Volume Flow 26
5.5.5 Performance Diagrams 26
5.6 Pressure Regulator Unit 28
5.7 Pressure Relief 28
5.7.1 High-Pressure Filter (Option) 28
5.8 Air Filter Set PC (Option) 29
5.9 Heater Set PC (Option) 30
5.10 Feed Pump (Option) 31
6 ASSEMBLY AND COMMISSIONING 32
6.1 Training Assembly/Commissioning Sta 32
6.2 Storage and Installation Conditions 32
6.3 Transportation 32
6.4 Assembling the Pump 33
6.4.1 Ventilation of the Spray Booth 33
6.5 Grounding 34
6.6 Commissioning 35
7 OPERATION 36
7.1 Training the Operating Sta 36
7.2 Safety Instructions 36
7.2.1 General Rules for Making Adjustments to the Spray Gun 37
7.3 Emergency Stop 37
7.4 Spraying 38
7.5 Pressure Relief/Work Interruption 38
7.6 Basic Flushing 39
7.6.1 Filling with Working Material 39
8 CLEANING AND MAINTENANCE 40
8.1 Cleaning 40
8.1.1 Cleaning Sta 40
8.1.2 Safety Instructions 40
8.1.3 Decommissioning and Cleaning 41
8.1.4 Long-term Storage 41
5
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
Table of Contents
8.2 Maintenance 42
8.2.1 Maintenance Sta 42
8.2.2 Safety Instructions 42
8.2.3 Regular Maintenance Work 43
8.2.4 Filling Separating Agent 43
8.2.5 Emptying the Pump 44
8.2.6 Filling the Empty Pump 45
8.2.7 Cleaning and Replacing the High-pressure Filter 46
8.2.8 Product Hoses, Tubes and Couplings 47
9 TROUBLESHOOTING AND RECTIFICATION 48
10 REPAIRS 49
10.1 Repair Sta 49
10.2 Mounting Materials 49
11 DISPOSAL 49
12 ACCESSORIES 50
12.1 Accessories for Product Outlet 50
12.2 Accessories for Product Inlet 52
12.2.1 Suction Hose 52
12.2.2 20 Liter Tank 53
12.3 Accessories for Trolley and Wall Mount 54
13 SPARE PARTS 55
13.1 How Can Spare Parts Be Ordered? 55
13.2 Overview of the Components 56
13.3 Air Motors 58
13.3.1 Jaguar Air Motor 9" 58
13.3.2 Air Motor Regulator for Jaguar and PROTEC 62
13.3.3 PROTEC Air Motor 10" 63
13.3.4 Tiger Air Motor 12" 67
13.3.5 Tiger Air Motor Regulator 71
13.4 Connection Sets 72
13.5 Fluid Sections 73
13.5.1 Fluid Section 150 cm3 73
13.5.2 Fluid Sections 200 cm3 – 240 cm3 76
13.5.3 Fluid Section 300 cm3 79
13.6 High-pressure Filter (up to 530 bar; 7687 psi) 82
13.7 Suction Hose DN38 84
13.8 Suction Tube PC 85
13.9 PC Heavy Duty Trolley 86
13.9.1 Air Filter Set PC 87
13.9.2 Heater Set PC 88
14 WARRANTY AND CONFORMITY DECLARATIONS 89
14.1 Important Notes Regarding Product Liability 89
14.2 Warranty Claim 89
14.3 CE Declaration of Conformity 90
14.4 Notes on National Regulations and Guidelines 90
6
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
1.2 WARNINGS, NOTICES AND SYMBOLS IN THESE INSTRUCTIONS
1 ABOUT THESE INSTRUCTIONS
Warning instructions in this operating manual highlight particular dangers to users and to
the device and state measures for avoiding the hazard. These warning instructions fall into
the following categories:
Danger - immediate risk of danger.
Non-observance will result in death or serious injury.
Warning - possible imminent danger.
Non-observance may result in death or serious injury.
Caution - a possibly hazardous situation.
Non-observance may result in minor injury.
Notice - a possibly hazardous situation.
Non-observance may result in damage to property.
Note - provides information about particular characteristics and how to proceed.
This notice warns you of a hazard!
Possible consequences of not observing the warning instructions.
The signal word indicates the hazard level.
The measures for preventing the danger and its
consequences.
DANGER
This notice warns you of a hazard!
Possible consequences of not observing the warning instructions.
The signal word indicates the hazard level.
The measures for preventing the danger and its
consequences.
WARNING
This notice warns you of a hazard!
Possible consequences of not observing the warning instructions.
The signal word indicates the hazard level.
The measures for preventing the danger and its
consequences.
CAUTION
This notice warns you of a hazard!
Possible consequences of not observing the warning instructions. The signal word
indicates the hazard level.
The measures for preventing the danger and its consequences.
NOTICE
1.1 PREFACE
The operating manual contains information about safely operating, maintaining, cleaning
and repairing the device.
The operating manual is part of the device and must be available to operating and service
sta .
The device may only be operated by trained sta and in compliance with this operating
manual. Operating and service personnel should be instructed according to the safety
instructions.
This equipment can be dangerous if it is not operated according to the instructions in this
operating manual.
7
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
1.3 LANGUAGES
The operating manual is available in the following languages:
Language Order No. Language Order No. Language Order No.
German 2340281 English 2340282 French 2340285
Italian 2340284 Spanish 2340286 Russian 2351798
Japanese 2359824
The corresponding service manuals are available under the following
order number:
Language Order No. Language Order No.
German 2335993 English 2335994
1.4 ABBREVIATIONS IN THE TEXT
Continuous- ow heater operating manual:
Language Order No. Language Order No.
German 65860 English 65860
French 65860 Italian 65860
1.3.1 OPERATING MANUALS FOR THE INDIVIDUAL COMPONENTS
Number of pieces
Position
Marking in the spare parts lists
Order No. Order number
Double stroke
DN Nominal diameter
PN Nominal pressure
Two components
: Heavy duty
corrosion protection
Materials
Stainless steel
Polyethylene
Ultra-high molecular weight
polyethylene
Polytetra uorethylene
PTFE with graphite
PTFE
Leather
Additional languages on request or at:
Additional languages on request or at:
8
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
1.5 TERMINOLOGY FOR THE PURPOSE OF THIS MANUAL
Cleaning Manual cleaning of devices and device parts with cleaning
agent
Flushing Internal ushing of paint-wetted parts with ushing agent
Sta quali cations
Trained person Is instructed in the tasks assigned to him/her, the potential
risks associated with improper behavior as well as the
necessary protective devices and measures.
Electrically trained
person
Is instructed by an electrician about the tasks assigned to him/
her, the potential risks associated with improper behavior as
well as the necessary protective devices and measures.
Electrician Can assess the work assigned to him/her and detect possible
hazards based on his/her technical training, knowledge and
experience in relevant provisions.
Skilled person A person who, based on his/her technical training, experience
and recent vocational experience, has su cient technical
knowledge and is familiar with the relevant and generally
accepted rules of technology so that he/she can inspect and
assess the status of devices and coating systems based on
workplace safety.
In the context of
TRBS1203 (2010 /
Revision 2012)
Additional requirements for skilled persons are given in
the TRBS1203(2010/Revision 2012): Expert knowledge in
the areas of protection against excessive pressure, electrical
hazards, and explosion protection (where applicable).
9
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
2 CORRECT USE
2.1 DEVICE TYPES
2.2 TYPE OF USE
2.3 USE IN AN EXPLOSION HAZARD AREA
Pneumatic pump with spraypack:
The device is suitable for processing liquid materials like paints and lacquers in accordance
with the classi cation into explosion classes IIA or IIB.
The pneumatic pump can be employed in explosion hazard zones (Zone 1). See Chapter 3.
2.4 SAFETY PARAMETERS
WAGNER accepts no liability for any damage arising from incorrect use.
Use the device only to work with the products recommended by WAGNER.
Only operate the device as a whole.
Do not deactivate safety xtures.
Use only WAGNER original spare parts and accessories.
The pneumatic pump may only be operated under the following conditions:
The operating sta must be trained on the basis of this operating manual.
The safety regulations listed in this operating manual must be observed.
The operating, maintenance and repair information in this operating manual must
be observed.
The statutory requirements and accident prevention regulation standards in the
country of use must be observed.
10
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
2.5 PROCESSIBLE WORKING MATERIALS
Abrasive working materials and pigments!
Greater wear of parts carrying the product.
Do not use any grainy and abrasive working materials with large, sharp-edged
pigments.
Use the application-related model ( ow rate/cycle, material packaging, valve seat,
etc.), as speci ed in Chapter 5.5.
Check if the uids and solvents used are compatible with the pump construction
materials as indicated in Chapter 5.5.1.
NOTICE
Wear caused by abrasive working materials is not covered by the warranty.
Working materials
Water-dilutable products
Solvent based materials
Primers
Epoxy and polyurethane lacquers, phenolic lacquers
Underside protection, re protection materials
Legend
recommended limited suitability less suitable
Application area
Steel-processing industry
Rail vehicle
Shipbuilding
Tank construction
Pipeline construction
Wind energy
Legend
recommended limited suitability less suitable
2.6 RECOMMENDED APPLICATION AREAS
11
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
2.8 RESIDUAL RISKS
Residual risks are risks which cannot be ruled out even in the event of correct use.
If necessary, warning and prohibition signs at the relevant points of risk indicate residual
risks.
Residual risk Source Consequences Speci c measures Lifecycle phase
Skin contact with
lacquers and
cleaning agents
Handling of
lacquers and
cleaning agents
Skin irritation,
allergies
Use personal safety
equipment.
Operation,
Observe safety data
sheets
maintenance,
disassembly
Lacquer in air
outside the de ned
working area
Lacquering outside
the de ned
working area
Inhalation of
substances
hazardous to
health
Observe work and
operation instructions.
Use personal safety
equipment
Operation,
maintenance
2.7 REASONABLY FORESEEABLE MISUSE
The forms of misuse listed below may result in physical injury or property damage:
coating work pieces which are not grounded;
unauthorized conversions or modi cations to the pneumatic pump;
processing dry or similar coating products, e.g., powder;
using defective components, spare parts or accessories other than those described in
the "Accessories" chapter of this operating manual;
continuing work with a defective or kinked product hose;
working with incorrectly set values;
processing food.
12
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
3.1 EXPLOSION PROTECTION IDENTIFICATION
3.2 IDENTIFICATION X
As de ned in Directive 94/9/EC (ATEX 95), the device is suitable for use in potentially
explosive areas.
CE CE mark (European Communities)
Explosion-proof equipment
II Device class II (not mining)
2 Category 2 device (suitable for zone 1)
G Ex-atmosphere gas
c Constructional security
IIB Device class (Gas) IIB
T3 Temperature class T3: maximum surface temperature 200 °C; 392 °F
T4 Temperature class T4: maximum surface temperature 135 °C; 275 °F
X There are special notices for safe operation
See the following Chapter
"Identi cation X".
3 IDENTIFICATION
Maximum surface temperature
The maximum surface temperature T3 of the piston pump can be reached if it runs dry.
Ensure that the piston pump is lled with su cient working or ushing agent.
Ensure that the separating agent tank is lled with su cient separating agent.
Temperature class T3: No dry running protection.
Temperature class T4: With dry running protection.
Ignition temperature
Ensure that the ignition temperature of the surrounding gases (pumping product,
cleaning agents) is higher than the maximum permitted surface temperature of the
device.
Ambient temperature
The permissible ambient temperature is: +5 °C to +50 °C; +41 °C to +122 °F.
Medium supporting atomizing
To atomize the product, use only weakly oxidizing gases, e.g., air.
13
150 cm3 - 300 cm3
Pumpentyp / Pump type
Max. Materialdruck / Fluid pressure
Übersetzungsverhältnis / Ratio
Fördermenge DH / Delivery DS
Max. Luftdruck / Air pressure
Max. Temp. Material / Fluid
Baujahr - Serie Nr. / Year of manufacture - Serial No.
Vor Gebrauch Betriebsanleitung beachten / Check manual before use!
J. WAGNER AG
MADE IN SWITZERLAND
CH-9450 ALTSTÄTTEN
II 2 G c IIB T3/T4 X
1
2
4
5
6
7
8
9
3
B_05439
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
Safe handling of WAGNER spray devices
Mechanical sparks can form if the device comes into contact with metal.
In an explosive atmosphere:
Do not knock or push the device against steel or rusty iron.
Do not drop the device.
Use only tools that are made of a permitted material.
Surface spraying, electrostatics
Do not spray device parts using electrostatic equipment.
Cleaning
If there are deposits on the surfaces, the device may form electrostatic charges. Flames or
sparks can form during discharge.
Remove deposits from the surfaces to maintain conductivity.
Use only a damp cloth to clean the device.
National regulations
Ensure that the national explosion prevention rules and regulations are observed when
setting up the device.
Air in the pump uid
Flammable gas mixtures can form if air reaches the pump uid.
Prevent the pump from taking in air and running dry.
If air has been taken in, x the leak. Then, ll slowly and in a controlled manner until the
air has escaped.
Air in the pumped uid can be caused by damaged packings.
Avoid operating the pump with damaged packing.
Ensure that the separating uid tank is lled with su cient separating uid.
Periodically check that the pump is working smoothly, paying special attention to the
presence of air in the pumped uid.
Filling and emptying
Flammable gas mixtures can form in the uid section or product hoses if the pump must
be emptied for maintenance.
Empty and ll the device slowly and in a controlled manner.
Avoid potentially explosive atmosphere in the surroundings.
3.3 TYPE PLATE
1 Manufacturer and CE
Identi cation
2 Pump type
3 Maximum product pressure
4 Pump ratio
5 Flow rate per double stroke
6 Maximum air inlet pressure
7 Maximum product temperature
8 Model year - serial number
9 Read operating manual before
use!
14
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
4 GENERAL SAFETY INSTRUCTIONS
4.1 SAFETY INSTRUCTIONS FOR THE OPERATOR
Keep this operating manual at hand near the device at all times.
Always follow local regulations concerning occupational safety and accident prevention.
4.1.1 ELECTRICAL EQUIPMENT
Electrical devices and equipment
To be provided in accordance with the local safety requirements with regard to the
operating mode and ambient in uences.
May only be maintained by skilled electricians or under their supervision. With open
housings, there is a danger from line voltage.
Must be operated in accordance with the safety regulations and electrotechnical
regulations.
Must be repaired immediately in the event of problems.
Must be decommissioned if they pose a hazard or are damaged.
Must be de-energized before work is commenced on active parts. Inform sta about
planned work. Observe electrical safety regulations.
Ground all devices to a common grounding point.
Only operate the device with a properly installed socket with a protective ground wire
connection.
Keep liquids away from electrical devices.
4.1.2 PERSONNEL QUALIFICATIONS
Ensure that the device is only operated, maintained and repaired by trained persons.
4.1.3 SAFE WORK ENVIRONMENT
Ensure that the oor in the working area is static dissipative in accordance with
EN61340-4-1 (resistance must not exceed 100 megohms).
Paint mist extraction systems/ventilation systems must be tted on site according to
local regulations.
Ensure that product / air hoses adapted to the working pressure are used.
Ensure that personal protective equipment is available and is used.
Ensure that all persons within the working area wear static dissipative shoes. Footwear
must comply with EN 20344. The measured insulation resistance must not exceed
100megohms.
15
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
Always follow the information in this manual, particularly the general safety instructions
and the warning instructions.
Always follow local regulations concerning occupational safety and accident
prevention.
In electrostatics application: Anyone tted with a pacemaker must not enter the high-
voltage area!
4.2 SAFETY INSTRUCTIONS FOR STAFF
Ensure that during spraying, persons wear static dissipative gloves. The grounding
takes place via the spray gun handle.
Protective clothing, including gloves, must comply with EN 1149-5. The measured
insulation resistance must not exceed 100 megohms.
Ensure that there are no ignition sources such as naked ames, sparks, glowing wires,
or hot surfaces in the vicinity. Do not smoke.
Ensure that the pipe joints, hoses, equipment parts and connections are permanently,
technically leak-proof:
- Periodic preventative maintenance and service (replacing hoses, checking tightness
strength and connections, etc.)
- Regular monitoring of leaks and defects via visual inspection and odor testing, e.g.,
daily before commissioning, at the end of work or weekly.
In the event of defects, immediately bring the device or system to a stop and arrange
to have repairs carried out immediately.
Grounding
Make sure that the ground and potential equalization of all system parts are performed
reliably and continuously and can withstand the expected stress (e.g. mechanical
stress, corrosion).
The spray jet is under pressure and can cause dangerous injuries.
Avoid injection of paint or ushing agents:
Never point the spray gun at people.
Never reach into the spray jet.
Before all work on the device, in the event of work interruptions and functional faults:
- Relieve pressure from spray guns and devices.
- Secure spray guns against actuation.
- Switch o the energy/compressed air supply.
- Disconnect the control unit from the mains.
- In the event of functional faults, remedy the fault as described in the "Troubleshooting"
chapter.
4.2.1 SAFE HANDLING OF WAGNER SPRAY DEVICES
16
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
4.2.3 PRODUCT HOSES
Ensure that the hose material is chemically resistant to the sprayed products and the
ushing agents used.
Ensure that the product hose is suitable for the pressure generated.
Ensure that the following information can be seen on the high pressure hose:
- Manufacturer
- Permissible operating pressure
- Date of manufacture
4.2.2 GROUNDING THE DEVICE
Friction, owing liquids and air or electrostatic coating processes create charges. Flames or
sparks can form during discharge. Grounding prevents electrostatic charging.
Ensure that the device is grounded. See chapter "Grounding".
Ground the work pieces to be coated.
Ensure that all persons inside the working area are grounded, e.g., that they are wearing
static dissipative shoes.
Wear static dissipative gloves when spraying. The grounding takes place via the spray
gun handle.
The spray substance supply (spray substance tank, pump, etc.) must be grounded.
If needed, the liquid ejection devices must be checked by experts (e.g. Wagner service
technician) at least every 12 months for their work-safe condition in accordance with
DGUV regulation 100-500.
- For shut down devices, the examination can be suspended until the next start-up.
Carry out the work steps as described in the "Pressure Relief" chapter:
- If pressure relief is required.
- If the spraying work is interrupted or stopped.
- Before the device is cleaned on the outside, checked or serviced.
- Before the spray nozzle is installed or cleaned.
In the event of skin injuries caused by paint or ushing agents:
Note the paint or ushing agent that you have been using.
Consult a doctor immediately.
Avoid risk of injury from recoil forces:
Ensure that you have firm footing when operating the spray gun.
Only hold the spray gun brie y in a position.
17
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
4.2.4 CLEANING AND FLUSHING
Relieve the pressure from the device.
De-energize the device electrically.
Preference should be given to non- ammable cleaning and ushing agents.
When carrying out cleaning work with ammable cleaning agents, make sure that all
equipment and resources (e.g. collection tank, funnel, transport cart) are conductive or
static dissipative and grounded.
Observe the speci cations of the paint manufacturer.
Ensure that the ash point of the cleaning agent is at least 15 K above the ambient
temperature or that cleaning is undertaken at a cleaning station with technical
ventilation.
Take measures for workplace safety (see Chapter 4.1.3).
When commissioning or emptying the device, please note that an explosive mixture
may temporarily exist inside the lines and components of equipment:
- depending on the coating product used,
- depending on the ushing agent (solvent) used,
explosive mixture inside the lines and items of equipment.
Make sure that the hoses are laid only in suitable places. Hoses should not be laid in the
following places under any circumstances:
- in high-traffic areas
- at sharp edges
- on moving parts
- on hot surfaces
Ensure that the hoses are never run over by vehicles (e.g., fork lifts), or that the hoses are
never put under pressure from the outside in any other way.
Ensure that the hoses are never kinked. Observe maximum bending radii.
Make sure that the hoses are never used to pull or move the equipment.
The electrical resistance of the product hose, measured at both valves, must be less
than 1 megohm.
Suction hoses may not be subjected to pressure.
Several liquids have a high expansion coe cient. In some cases their volume can rise with
consequent damage to pipes, ttings, etc. and cause uid leakage.
When the pump sucks liquid from a closed tank, ensure that air or a suitable gas can
enter the tank. Thus a negative pressure is avoided. The vacuum could implode the tank
(squeeze) and can cause it to break. The tank would leak and the liquid would ow out.
The pressure created by the pump is a multiplication of the inlet air pressure.
18
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
4.2.6 TOUCHING HOT SURFACES
Only touch hot surfaces if you are wearing protective gloves.
When operating the device with a coating product with a temperature of > 43 °C;
109°F: identify the unit with a warning label that says "Warning - Hot Surface".
- Instruction label Order No. 9998910
- Protection label Order No. 9998911
Note: Order the two stickers together.
Only electrically conductive tanks may be used for cleaning and ushing agents.
The containers must be grounded.
An explosive gas/air mixture forms in closed containers.
Never spray into a closed tank when using solvents for ushing.
External cleaning
When cleaning the exterior of the device or its parts, also observe the following:
Disconnect the pneumatic supply line.
Use only moistened cloths and brushes. Never use abrasive agents or hard objects and
never spray cleaning agents with a gun. Cleaning the device must not damage it in any
way.
Ensure that no electric component is cleaned with or immersed into solvent.
4.2.5 HANDLING HAZARDOUS LIQUIDS, VARNISHES AND PAINTS
When preparing or working with lacquer and when cleaning the device, follow the
working instructions of the manufacturer of the lacquers, solvents and cleaning agents
being used.
Take the speci ed protective measures. In particular, use personal protective equipment:
safety goggles, protective clothing and gloves, as well as respiratory protection and
skin protection cream if necessary.
Use a mask or breathing apparatus if necessary.
For su cient health and environmental safety: Operate the device in a spray booth or
on a spraying wall with the ventilation (extraction) switched on.
Wear suitable protective clothing when working with hot products.
19
150 cm3 - 300 cm3
B_04263
10
9
8
7
5
3
2
1
4
11
6
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
The piston pump is driven with compressed air (2). This compressed air moves the air
piston up and down in the air motor (4) and it also moves the associated pump piston up
and down in the uid section (9).
In the control housing (1), the air pressure is redirected at the end of each stroke with the
help of the reversing valve. The working material is sucked up during the upwards stroke
and is continuously conveyed towards the product outlet (8) in both stroke directions.
Air motor (4)
The air motor with its pneumatic reverse (1) does not require pneumatic oil.
The compressed air is fed to the motor via the air regulator (2) and the ball valve (3).
Fluid section (9)
The uid section has been designed as a piston pump with exchangeable ball valves. The
hard chrome-plated pump piston runs in two xed packings which are self-adjusting by
means of a pressure spring, thus resulting in a long service life.
Between the air motor and the uid section there is a separating agent cup (7) for separating
the separating agent.
1 Control housing with integrated silencer
2 Air pressure regulator
3 Ball Valve
4 Air motor
5 Compressed air Inlet
6 Mounting ange
7 Separating agent cup
8 Material outlet
9 Fluid section
10 Material inlet
11 Grounding connection
5 DESCRIPTION
5.1 DESIGN
5.2 MODE OF OPERATION
20
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
5.4 SCOPE OF DELIVERY
Pneumatic piston pump
Consists of:
- Fluid section
- Air motor
- Connection elements
- Air pressure regulator for air motor
The scope of delivery also includes:
Separating agent 250 ml; 250 cc Order No.: 9992504
Declaration of conformity See Chapter 14
Operating manual, German Order No.: 2340281
Operating manual in the local language See Chapter 1.3
The delivery note shows the exact scope of delivery. Accessories: see Chapter 12.
5.3 PROTECTIVE AND MONITORING EQUIPMENT
Safety valve
The air motor is tted with a safety valve. The safety valve has been set and sealed at the
factory. In case of pressures over and above the permissible operating pressure, the valve,
which is held with a spring, automatically opens and releases the excess pressure.
Overpressure!
Risk of injury from bursting components.
Never change the safety valve setting.
WARNING
21
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
5.5.2 RECOMMENDED PACKINGS
5.5 DATA
5.5.1 MATERIALS OF PAINTWETTED PARTS
Housing Stainless steel
Piston Stainless steel and hard chrome
Valve balls Stainless steel
Valve seats Carbide
O-rings PTFE
Packings Standard
= Ultra high molecular weight polyethylene
= PTFE with graphite
WAGNER packings are manufactured in four di erent materials:
Product Color
Leather dark brown
PTFE with graphite black
Ultra high molecular weight
polyethylene
transparent
PTFE white
Each product has the following properties, which in uence the packings:
Mechanical stability poor good good poor
Friction coe cient poor very good good very good
Sealing force good* good good good
Chemical resistance poor good very good very good
Temperature resistance good poor - good very good poor
for abrasive products
Standard combinations
Standard pumps:
Heavy-duty (high-pressure) pumps:
Hardener pumps in 2K systems:
5.5.3 TECHNICAL DATA
Outgoing air containing oil!
Risk of poisoning if inhaled.
Air motor switching problems.
Provide water-free and oil-free compressed air
WARNING
22
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
Description
Measuring
unit
Pump ratio 75:1 55:1 60:1
Volume ow per double stroke cm; cc 150 200 240
Maximum operating overpressure
MPa 53 44 48
bar 530 440 480
psi 7687 6382 6962
Maximum possible strokes in operation
/min. 60
Maximum recommended strokes per minute in
continuous operation
/min. 40
Minimum/maximum air inlet pressure
MPa 0.25–0.71 0.25–0.80
bar 2.5–7.1 2.5–8.0
psi 36–103 36–116
Compressed air quality: free from oil and water
Quality standard 7.5.4 according to ISO 8573.1, 2010
7: Particle concentration 5–10mg/m
5: Humidity: Pressure dew point ≤ +7 °C
4: Oil content ≤ 5mg/m
Air inlet (inside thread) inch G1"
Minimum of the compressed air supply line mm; inch 25; 0.98
Air consumption at 0.6 MPa; 6 bar; 87 psi per
double stroke
nl 79.9 103.1
scf 2.82 3.64
Air motor piston diameter mm; inch 220; 8.7 250; 9.8
Air motor piston stroke mm; inch 150; 6
Sound pressure level at maximum permissible air
pressure*
dB(A) 83 83
Sound pressure level at 0.6 MPa; 6 bar; 87 psi air
pressure*
dB(A) 81 80
Sound pressure level at 0.4 MPa; 4 bar; 58 psi air
pressure*
dB(A) 69 76
Product inlet connection (inside thread) mm G1½"
Product outlet (outside thread) mm M24x1.5
Weight kg; lb 53; 117 60.5; 133.5
Product pH value pH 3.5–9
Maximum product pressure at pump inlet
MPa 2
bar 20
psi 290
Material temperature
+5…+80; +41…+176
Ambient temperature
Construction and
assembly
+5…+50; +41…+122
Suspension -20…+60 ; -4…+140
Relative humidity % 10–95 (without condensation)
Allowable inclination for operation
± 10
A rated sound pressure level measured at 1 m distance, LpA1m, according to DIN EN 14462: 2005.
Reference measurements have been made by SUVA (Swiss Accident Insurance Institute).
5.5.3.1 TECHNICAL DATA FOR JAGUAR AND PROTEC
23
150 cm3 - 300 cm3
R
S
H
Q
O
P
B_03905
G
G/2
I (IbxIh) Ib
Ih
J
C
F
T
H
D
(E)
A
G
K
B
B_04260
M
L2
L1
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
Jaguar / PROTEC
wall mount
5.5.3.2 MEASUREMENTS AND CONNECTIONS FOR JAGUAR AND PROTEC
mm; inch mm; inch mm; inch
A 1145; 45.0 1157; 45.5 1169; 46.0
B 304; 12
C ~582; 22.9
D 470; 18.5 483; 19.0
E 675; 26.6 687; 27.0
F 244; 9.6
G 230; 9.1
H 110; 4.3
I 20x48; 0.8x1.9
J M8
K G1½" (female thread)
L1 M24x1.5 (outside thread)
L2 G3/8" G1/2"
M G1"
O 135.5; 5.3
P 238; 9.4
Q
9; 0.35
R 9; 0.35
S 206; 8.1
T 17; 0.67
24
150 cm3 - 300 cm3
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
Description
Measuring
Unit
Pump ratio - 72 :1
Volume ow per double stroke ( ) cm; cc 300
Maximum operating overpressure MPa; bar; psi 53; 530; 7687
Maximum possible strokes in operation
/min. 40
Maximum recommended strokes per minute in
continuous operation
/min. 30
Minimum/maximum air inlet pressure MPa; bar; psi 0.25-0.74; 2.5-7.4; 36-107
Compressed air quality: free from oil and water
Quality standard 7.5.4 according to ISO 8573.1, 2010
7: Particle concentration 5–10mg/m
5: Humidity: Pressure dew
point ≤ +7 °C
4: Oil content ≤ 5mg/m
Air inlet (inside thread) inch G 1"
Minimum Ø of the compressed air supply line mm; inch 25; 1.0
Air consumption at 0.6 MPa; 6 bar; 87 psi per double stroke
nl; scf 170; 6
Air motor piston diameter mm; inch 300; 11.8
Air motor piston stroke mm; inch 150; 5.9
Sound pressure level at maximum permissible air pressure*
82
Sound pressure level at 0.6 MPa; 6 bar; 87 psi air pressure* 80
Sound pressure level at 0.4 MPa; 4 bar; 58 psi air pressure* 75
Product inlet connection (inside thread) mm G1 1/2"
Product outlet (outside thread) mm M24x1.5
Weight kg; lb 80; 176
Product pH value pH 3.5–9
Maximum product pressure at pump inlet MPa; bar; psi 2; 20; 290
Material temperature
+5…+80; 41…176
Ambient temperature
Construction and assembly
+5…+50; 41…122
Suspension
-20…+60 ; -4…+140
Relative humidity % 10–95 (without condensation)
Allowable inclination for operation
± 10
* A rated sound pressure level measured at 1 m distance, L pA1m, according to DIN EN 14462: 2005.
Reference measurements have been made by SUVA (Swiss Accident Insurance Institute).
5.5.3.3 TECHNICAL DATA FOR TIGER
Outgoing air containing oil!
Risk of poisoning if inhaled.
Air motor switching problems.
Provide water-free and oil-free compressed air
WARNING
25
150 cm3 - 300 cm3
R
S
H
Q
O
P
B_03905
G
G/2
I (IbxIh) Ib
Ih
I
J
C
F
T
H
M
D
(E)
A
G
K
B
B_04261
L2
L1
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
Unit
A 1106 mm
43.5 inch
B 340 mm
13.4 inch
C 562 mm
22.1 inch
D 518 mm
20.4 inch
E 588 mm
23.1 inch
F 244 mm
9.6 inch
G 230 mm
9.1 inch
Wall mount
Unit
H 110 mm
4.3 inch
I 20x48 mm
0.8x1.9 inch
JM8
mm
K G1 1/2" mm
L1 M24x1.5 mm
L2 G3/4" inch
M G 1" inch
O 135 mm
5.3 inch
P 238 mm
9.4 inch
Unit
Q 9mm
0.35 inch
R
9mm
0.35 inch
S 206 mm
8.1 inch
T32 mm
1.3 inch
5.5.3.4 MEASUREMENTS AND CONNECTIONS FOR TIGER
26
150 cm3 - 300 cm3
BAR
BAR
BAR
BAR
BAR
BAR
"?
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
5.5.4 VOLUME FLOW
5.5.5 PERFORMANCE DIAGRAMS
Stroke frequency /min
Product pressure bar (MPa) psi
Air consumption nl/min <scfm>
Water ow rate l/min <gpm>
Example diagram
Wagner AL nozzles Volume ow* in l/min
at at at at
Maximum ranges for
continuous operation
at 40 DH/min (Jaguar,
PROTEC) or 30 DH/min
(Tiger)
7 MPa 10 MPa 15 MPa 20 MPa
70 bar 100 bar 150 bar 200 bar
inch mm Spray angle 1015 psi 1450 psi 2175 psi 2900 psi
0.007 0.18 40° 0.17 0.20 0.21 0.22
0.009 0.23 20-30-40-50-60° 0.21 0.25 0.31 0.36
0.011 0.28 10-20-30-40-50-60° 0.30 0.35 0.43 0.50
0.013 0.33 10-20-30-40-50-60-80° 0.45 0.53 0.62 0.68
0.015 0.38 10-20-30-40-50-60-80° 0.58 0.67 0.81 0.91
0.017 0.43 20-30-40-50-60-70° 0.73 0.79 1.06 1.23
0.019 0.48 20-30-40-50-60-70-80° 0.93 1.09 1.37 1.47
0.021 0.53 20-40-50-60-80° 1.14 1.36 1.69 1.78
0.023 0.58 20-40-50-60-70-80° 1.37 1.59 2.01 2.24
0.025 0.64 20-40-50-60-80° 1.62 1.91 2.40 2.60
0.027 0.69 20-40-50-60-80° 1.83 2.13 2.68 3.12
0.029 0.75 60° 2.19 2.51 3.17 3.63
0.031 0.79 20-40-50-60° 2.40 2.77 3.49 4.00
0.035 0.90 20-40-50-60° 3.22 3.74 4.69 5.14
0.043 1.10 20-50° 5.07 6.04 7.46 7.84
0.052 1.30 50° 5.12 6.10 7.52 8.06
Volume ow refers to water.
27
150 cm3 - 300 cm3
!
"
#
BAR-0A
PSI
NLMIN
SCFM
LMIN
GPM
!
"
#
"?
0
500 (50)
<7250>
400 (40)
<5800>
300 (30)
<4350>
200 (20)
<2900>
100 (10)
<1450>
0
10 20 30 40 50 60
5000
<175>
4000
<140>
3000
<105>
2000
<70>
1000
<35>
0
12
<3.2>
10
<2.7>
8
<2.1>
6
<1.6>
4
<1.1>
2
<0.5>
0
A
B
C
bar (MPa)
<psi>
nl/min
<scfm>
l/min
<gpm>
A
B
C
B_04262
0
500 (50)
<7250>
400 (40)
<5800>
300 (30)
<4350>
200 (20)
<2900>
100 (10)
<1450>
0
10 20 30 40 50 60
5000
<175>
4000
<140>
3000
<105>
2000
<70>
1000
<35>
0
0
A
B
C
bar (MPa)
<psi>
nl/min
<scfm>
l/min
<gpm>
A
C
B
14.4
<3.8>
12
<3.2>
9.6
<2.5>
7.2
<1.9>
4.8
<1.3>
2.4
<0.6>
B_05288
0
300 (30)
<4350>
200 (20)
<2900>
100 (10)
<1450>
0
10 20 30 40 50 60
9000
<318>
6000
<212>
3000
<106>
0
18
<4.8>
15
<4>
12
<3.2>
9
<2.4>
6
<1.6>
3
<0.8>
0
A
B
C
bar (MPa)
<psi>
nl/min
<scfm>
l/min
<gpm
>
A
B
C
400 (40)
<5800>
500 (50)
<7250>
12000
<424>
15000
<530>
B_00321
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
PROTEC 60-240
Stroke frequency /min
Product pressure
Air consumption
Water ow rate
A = 8 bar (0.8 MPa; 116 psi) air pressure
B = 6 bar; 0.6 MPa; 87 psi air pressure
C = 4 bar; 0.4 MPa; 58 psi air pressure
Tiger 72-300
Stroke frequency
/min
Product pressure
Air consumption
JAGUAR 75-150
Stroke frequency
/min
Product pressure
Air consumption
JAGUAR 55-200
Stroke frequency /min
Product pressure
Air consumption
Water ow rate
A = 8 bar (0.8 MPa; 116 psi) air pressure
B = 6 bar; 0.6 MPa; 87 psi air pressure
C = 4 bar; 0.4 MPa; 58 psi air pressure
Water ow rate
A = 7.1 bar (0.71 MPa; 103 psi) air pressure
B = 6 bar; 0.6 MPa; 87 psi air pressure
C = 4 bar; 0.4 MPa; 58 psi air pressure
Water ow rate
A = 7.4 bar (0.74 MPa; 107 psi) air pressure
B = 6 bar (0.6 MPa; 87 psi) air pressure
C = 4 bar (0.4 MPa; 58 psi) air pressure
28
150 cm3 - 300 cm3
1
2
3
B_03907
B_04264
2
3
1
B_04265
B_05295
3
1
2
4
OPERATING MANUAL
VERSION 05/2015 ORDER NUMBER DOC2340282
5.6 PRESSURE REGULATOR UNIT
1 Pressure regulator
2 Ball Valve
3 Pressure gauge
4 Compressed air Inlet
Positions of the ball valve
1 Closed: working pressure in the air motor will be
relieved (control pressure is still present).
2 Closed: the air motor may still be under pressure.
3 Open: working position
5.7 PRESSURE RELIEF
5.7.1 HIGHPRESSURE FILTER OPTION
To ensure problem-free operation it is recommended that a WAGNER high-pressure lter
be used. These have been developed especially for WAGNER pneumatic pumps. The lter
inserts can be exchanged depending on the product to be used. The high-pressure lter
corresponding to the device can be found in the "Accessories" chapter; the compatible
lter inserts can be found in the "Spare parts" chapter.
Closed
Open
Preferred lter
installation position
So that the complete pressure relief of the pump can be performed (see Chapter 7.5), a
high-pressure lter with a return ow or a relief combination, is mandatory.
1 Fluid section
connection
2 Material outlet
3 Return line
53MPa
530bar
7687psi