WAC Lighting HR-3LED-H18D-ICA, HR-3LED-H18D- EMICA, HR-3LED-H18D1-ICA Installation Instruction
INSTALLATION INSTRUCTION
Tesla 3” LED - IC New Construction Housing
HR-3LED-H18D-ICA, HR-3LED-H18D-EMICA, HR-3LED-H18D1-ICA
SAFETY INSTRUCTION
IMPORTANT: NEVER attempt any work without shutting o the electricity.
• Read all instructions before installing.
• System is intended for installation by a qualied electrician in accordance with the National Electrical Code and
local regulations.
• Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the
fuse(s) or switch ”OFF” the circuit breaker switch(es) that control the power to the xture or room that you are working on.
• Place the wall switch in the “OFF” position.
CAUTION:
All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
OVERVIEW:
Housing is new construction IC, AIRTIGHT. Housing requires a trim for nished look. Check catalog for various trims choices.
HOUSING INSTALLATION:
1. Install housing using two hanger bar provided, align the bottom of the hanger bar with the bottom of the wood joist,
secure the “screw-nail” on each end by screw-driver or by hammer(See FIG.1 detail A).Slide xture along hanger bar into
desired location, use locking screws to secure (See FIG.1 detail B).
2. To shorten hanger bars to t in a 12” joist, snap o one section of the hanger bars (See FIG.2).
3. Remove spring latched junction box cover and connect xture wires to building wires: insert each supply wire into
appropriate junction box connector. Connect black xture wire to hot, white xture wire to neutral and green xture wire
to ground (as Fig.3). Place all wiring and connectors back in junction box and replace the junction box’s cover.
4. When installing in drywall, cut a hole 4 5/8” in the drywall. Note: 3/4” inch maximum ceiling thickness.
5. Connect power for trim to housing, depress trim spring clips and push the trim assembly up until the trim ring is ush
to the ceiling (as Fig.4,Fig.5 and Fig.6).
WAC Lighting
www.waclighting.com
Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JUNE, 2014
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
INSTALLATION INSTRUCTION
Tesla 3” LED - IC New Construction Housing
HR-3LED-H18D-ICA, HR-3LED-H18D-EMICA, HR-3LED-H18D1-ICA
WIRE DIMMER
VOUT +
HOT
BLACK
RED
LED
MODULE
VOUT
LED
DRIVER
DIM +
NEUTRAL
WHITE
DIM
COMPLETING THE INSTALLATION:
To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant)
to outline the outside of xture plate where it meets the wall. Leave some space at bottom to allow moisture to escape.
BLACK
BROWN
0 10V DIMMER
BLUE
WAC Lighting
www.waclighting.com
Phone (800) 526.2588 • Fax (800) 526.2585
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JUNE, 2014
Headquarters/Eastern Distribution Center
44 Harbor Park Drive • Port Washington, NY 11050
Phone (516) 515.5000 • Fax (516) 515.5050
Western Distribution Center
1750 Archibald Ave • Ontario, CA 91761
Phone (800) 526.2588 • Fax (800) 526.2585
Loading...