1
Congratulations
on purchasing your new VTech product. Before using this telephone, please read
Important safety instructions on page 5 of this manual.
This manual has instructions on how to set up and register your new handset.
For complete instructions on using the handset, see the Abridged user’s manual
that came with your telephone base.
You may also view or download the online Complete user’s manual for a
full set of installation and operation instructions at www.vtechphones.com.
In Canada, visit www.vtechcanada.com.
User’s manual
CS6109
DECT 6.0 accessory handset for use
with
VTech model CS6199-4
The ENERGY STAR® program (www.energystar.gov) recognizes
and encourages the use of products that save energy and help
protect our environment. We are proud to mark this product with
the ENERGY STAR® label indicating it meets the latest energy
efficiency guidelines.
T
Compatible with
Hearing Aid T-Coil
TIA-1083
Telephones identified with this logo have reduced noise and
interference when used with most T-coil equipped hearing
aids and cochlear implants. The TIA-1083 Compliant Logo is
a trademark of the Telecommunications Industry Association.
Used under license.
Register online to get an additional 3-month warranty!
Visit www.vtechphones.com.
Registration
Register your product online for enhanced
warranty support.
Product news
Learn about the latest VTech products.
2
Parts checklist
Your telephone package contains the following items. Save your sales receipt and
original packaging in the event warranty service is necessary.
Battery
Handset
Charger and
charger adapter
Battery compartment
cover
User’s manual
User’s manual
Battery installation
Install the battery as shown below.
Slide the battery compartment cover
towards the center of the handset
until it clicks into place.
3. Place the handset in the handset
charger to charge.
4.
If the handset will not be used for a long time, disconnect and remove the battery
to prevent possible leakage.
To purchase a replacement battery, visit our website at www.vtechphones.com
or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or dial
1 (800) 267-7377.
•
•
Insert the battery connector securely
into the socket.
1. Place the battery with the label
THIS SIDE UP facing up and the
wires inside the battery compartment.
2.
The LCD
backlight
turns on for
10 seconds
to denote the
battery starts
to charge.
3
Register a handset
Each new handset must be registered with the telephone base before use.
When properly charged, each expansion handset displays To register HS...
and ...see manual alternately. You may need to charge the handset before
registering it to the telephone base.
To register a handset:
Place the handset in the telephone base.
Wait for about 10 seconds. The handset shows Registering... and then
Registered briefly. You hear a confirmation tone when the registration
process completes.
Deregister handsets
If you want to replace a handset or reassign the designated handset number of a
registered handset, you must deregister all handsets and then individually register
each handset.
To deregister all handsets:
Press and hold on the telephone base for about 10 seconds.
Immediately press again.
All handsets show To register HS... and ...see manual alternately when the
deregistration process completes. The deregistration process takes about
10 seconds to complete.
1.
2.
1.
2.
3.
Battery charging
Once you have installed the battery, the screen indicates the battery status (see the
table below). For best performance, keep the handset in the handset charger when
not in use. The battery is fully charged after 11 hours of continuous charging.
Battery indicators Battery status Action
The screen is blank, or
shows Put in charger and
flashes.
The battery has no charge or
very little charge. The handset
cannot be used.
Charge without interruption
(at least 30 minutes).
The screen shows
Low battery and
flashes.
The battery has enough
charge to be used for a
short time.
Charge without interruption
(about 30 minutes).
The screen shows
HANDSET X.
The battery is charged. To keep the battery charged,
place it in the handset
charger when not in use.
If you place the handset in the handset charger without plugging in the battery, the
screen displays No battery.
Press and hold for about 10 seconds.
Loading...