VTech LS1250-B User Manual

Download

Page 1

User’s manual

www.euphones.vtech.com

LS1250-B

Page 2

1. IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should always

be followed to reduce the risk of re, electric shock and injury, including the

following:

Read and understand all the instructions.

Follow all warnings and instructions marked on the product.

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

Do not use this product near water (for example, near a bath tub, kitchen sink, swimming pool).

Do not expose the telephone to direct sunlight or extreme cold environment. Do not put the telephone close to heating sources such as radiators, cookers, etc.

Do not overload wall outlets and extension cords as this can result in the risk

of re or electric shock.

Unplug this product from the wall outlet and refer servicing to VTech/ distributor under the following conditions:

When the power supply cord or plug is damaged or frayed.

If the product does not operate normally by following the operating instructions.

If the product has been dropped and the cabinet has been damaged.

If the product exhibits a distinct change in performance.

Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

Do not use the telephone to report a gas leak in the vicinity of the leak.

Use only the supplied NiMH (Nickel Metal Hydride) batteries! The operation periods for the handsets are only applicable with the default battery capacities.

The use of other battery types or non-rechargeable batteries/primary cells can be dangerous. These may cause interference and/or unit damages. The manufacturer will not be held liable for damage arising from such non-compliance.

Do not use third party charging bays. The batteries may be damaged.

Please note the correct polarity while inserting the batteries.

Battery should not be exposed to excessive heat such as bright sunshine or

re and immersed in water.

•

10.

11.

12.

13.

14.

Page 3

DISPOSAL WARNING

When this crossed-out wheeled bin symbol is attached to a product, it means the product is covered by the European Directive 2002/96/EC.

All electrical and electronic products/battery should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

The correct disposal of your old appliance/battery will help prevent potential negative consequences for the environment and human health.

For more detailed information about disposal of your old appliance/battery,

please contact your city ofce, waste disposal service or the shop where you

purchased the product.

If you have questions about this product, or having difculty with setup or

operation, contact our Customer Service Centre.

POWER ADAPTOR INFORMATION

Power adaptor

Ten Pao International Ltd. - Model: S003IV0600045,

Input 100-240V AC 50/60Hz 150mA,

Output 6VDC 450mA (EU plug).

Battery Handset: NI-MH PACK x1, 2.4V, 750mAh

Doorbell: ALKALINE CELL, AAx2, 1.5V; 2800mAh

For pluggable equipment, the socket outlet shall be installed near the equipment and shall be easily accessible.

Page 4

2. SET UP THE TELEPHONE

2.1 Package Contents

The package contains the following items:

Telephone base and power adapter

Handset (1 for IS7121A, 2 for IS7121-2A)

Handset charger and charger adapter (1 for IS7121-2A)

Doorbell with wall mount cover

Telephone Wall mount bracket

Battery compartment cover (1 for IS7121A, 2 for IS7121-2A)

NiMH Rechargeable battery pack (1 for IS7121A, 2 for IS7121-2A)

AA Alkaline batteries (2)

Screw for doorbell (bottom)

Screw for doorbell (wall mount)

Wall anchors

Double-sided adhesive tape

Telephone line cord

User’s manual

Warranty card

•

Page 5

2.2 Connect the Base Station

note

Use only the supplied power adapter.•

A DSL lter (not

included) is required if you have DSL highspeed Internet service.

The DSL lter must

be plugged into the

telephone wall jack.

To telephone

wall jack

To wall power outlet

Page 6

2.3 Install and Charge the Handset Batteries

notes

Use only the supplied NiMH rechargeable batteries.

If you do not use the handset for a long time, disconnect and remove the batteries to prevent possible leakage.

•

Battery Pack

BT164392/BT264392

2.4V 550mAh Ni-MH

WARNING : DO NOT BURN OR

PUNCTURE BATTERIES

Made in China CR1222

1 2

3 4

CHARGE light

remains on when charging.

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

CR1232

Battery Pack / Bloc-piles :

(2.4V Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

CR1232

Page 7

2.4 Installation Options

Your telephone base is ready for tabletop use. If you want to mount your telephone on a wall, follow the steps below to connect the telephone base with a standard dual-stud telephone wall mounting plate. You may need a professional to install the wall mounting plate.

2.4.1 Tabletop to Wall Mount Installation

If you have already installed the telephone for tabletop use, unplug the

telephone line cord from the telephone wall jack, and unplug the telephone

base power adapter from the wall outlet. Remove the telephone line cord and the power adapter cord from the grooves.

2. Route the telephone line cord through the rectangular hole on the wall mount bracket. Position the lower portion grooves on the telephone base to the lower portion tabs on the wall mount bracket. Make sure the upper portion grooves of the telephone base are above the upper portion tabs on the wall mount bracket. Push the telephone base down until it clicks securely in place.

Page 8

3. Plug the telephone line cord into the telephone wall jack or DSL lter. Align the holes on the bracket with the standard wall plate and slide the bracket down until it locks securely.

4. Plug the power cord into an electrical outlet not controlled by a wall switch. Bundle the telephone line cord and power adapter cord neatly with twist ties.

Page 9

2.4.2 Wall Mount to Tabletop Installation

To change the telephone base from the wall mount position to tabletop position, follow the steps below.

If the telephone line cord and power adapter cord are bundled, untie them rst.

Slide the wall mount bracket up and remove it from the wall plate. Unplug the

telephone line cord (or DSL lter) from the wall. Unplug the power adapter from

the power outlet.

Slide the telephone base up and remove it from the wall mount bracket.

See section Connect the Base Station.

Page 10

2.5 Doorbell Battery Installation

Remove the wall mount cover at the back.

Install two AA batteries into the battery compartment, matching the polarity

markings (+ and -) inside the battery compartment.

Page 11

2.6 Locating the Doorbell

Before mounting the doorbell on a wall, make sure you test if the location you

install the doorbell is in range, and adjust the camera angle to best suit your needs.

To test the location for installation:

Hold the doorbell in the location where you want to install the doorbell, then follow

the steps below to test the reception range and video capture angle.

Press MENU →

→ Settings → SELECT.

Press

→ Doorbell setup → SELECT.

Press /DOORBELL → check video streaming quality.

Press NEXT.

Press ISO → + / - → adjust video streaming brightness.

If audio feedback occurs, press on the handset to turn off the

speakerphone.

If the desired location is in good range, the handset displays .

If the desired location is not in good range, the handset ashes in red.

Press INFO for instructions to relocate your handset and/or telephone

base. When the reception is in good range, the handset displays . Press

OK to return to the video streaming.

6. Keep the video streaming on for camera lens adjustment.

•

Page 12

Avoid mounting it to where reections may be caused by sunlight, for example,

opposite to a white wall.

Two built-in infrared LEDs are for night vision. Make sure the surrounding light

source is sufcient for infrared operation.

•

Infrared LEDs

When nding a desirable location for the doorbell:

Make sure the visitor is standing in a reasonable distance away from the

doorbell.

Avoid mounting it on a location which is subjected to vibration or shock.

Avoid mounting it on an enclosed area where it may cause echoes.

Avoid mounting it to where it is exposed to direct sunlight.

•

Page 13

The diagrams below demonstrate an example of doorbell camera position to view

a visitor about 20 inches from the camera. The camera in this example is set in

default angle (0 degree).

You may move the lever at the back of the doorbell to adjust the shooting area

(the camera lens).

Test at the front door to determine when the infrared LEDs turn on. When they are

in operation, they turn red.

To adjust the shooting area, you may either relocate the doorbell in different

height level, or adjust the camera angle (see below).

To adjust the camera angle:

Tilt the lever to adjust the angle of the camera lens. The camera lens can be

adjusted to left, right or down, up to 10 degrees.

•

View

Right

Angle

Adjustment

View

Left

View Right

Angle

Adjustment

View

Left

CAUTION

Page 14

You may install the doorbell in a lower position. The diagram below demonstrates

an example of doorbell camera position to view a visitor about 20 inches from the

camera. The camera in this example is set in 10 degrees angle upward.

Side view

inches

degrees

inches

Shooting area

inches

Top view

60 degrees

Shooting area

23 inches

20 inches

Side view

inches

50 degrees

63 inches

inches

Shooting area

Page 15

You may install the doorbell on the left or right side. The diagram below

demonstrates an example of doorbell camera position to view a visitor about 20

inches from the camera. The camera in this example is set in 10 degrees angle to

the right.

Top view

60 degrees

Shooting area

24 inches

20 inches

After you have tested the reception range and found the desirable location to

install the doorbell, press END on the handset to end the video streaming and

proceed to Install the Doorbell Wall Mount Cover and Install the Doorbell.

Page 16

2.7 Install the Doorbell Wall Mount Cover

Make sure to test the reception and the doorbell position before you mount the

doorbell on the wall. See Locating the doorbell to choose a desirable position

for the doorbell.

Use a pencil to mark two holes on the desired location. Then remove the wall

mount and drill two holes in the wall. Check for reception strength and camera

angle before drilling the holes.

2. Place the wall anchors into the holes, and tap gently on the ends with a

hammer, until the wall anchors are ush with the wall.

Page 17

Align the holes on the wall mount cover with the holes on the wall (or stud).

Tighten the screws into the holes to secure the wall mount cover onto the wall.

Page 18

Push the doorbell gently onto the wall mount until they are sealed tightly.

This doorbell meets the IPX4 waterproof standard. Make sure the doorbell

is tightly sealed with its wall mount cover in order to maintain its waterproof

ability.

Tighten the screw into the threaded socket at the bottom to secure.2.

Screw

Push

Seal tightly

2.8 Install the Doorbell

Page 19

2.9 Detach Doorbell From Wall Mount Cover

After an extended exposure to cold, heat or humidity, the doorbell gasket rubber

may become sticky.

If you need to remove the doorbell from its wall mount cover in case of battery

replacement or doorbell relocation, follow the steps below.

Remove the screw at the bottom.1. Insert a at-bladed screwdriver

between the doorbell and its

wall mount cover to pry open at

both sides.

Pry the doorbell off.3.

Page 20

3. GET TO KNOW YOUR PHONE

3.1 Overview of the Handset

CHARGE light

On when the handset is charging in the telephone base.

Soft keys (2)

Press to select a menu item displayed above the key.

Page 21

q/VOL-/CID Press to scroll down while in a menu, or in the directory, caller ID log or redial list. Press to review the caller ID log when the phone is not in use. While entering names or numbers, press to move the cursor to the left. During a call or message playback, press to decrease the listening volume.

/FLASH

Press to make or answer a call. During a call, press to answer an incoming home call when you receive a call waiting alert.

Dialing keys

Press to enter numbers or characters. Press to answer an incoming call.

During a call, press to switch to tone dialing if you have pulse service.

Press to make or answer a call using the handset speakerphone. Press to switch between the handset speakerphone and the handset earpiece during a call. While entering or editing a directory entry: Press to erase a digit or character. While the handset is ringing: Press to silence the ringer temporarily. During message or outgoing message playback: Press to delete a message or outgoing message.

MUTE/DELETE During a call, press to mute the microphone. While the phone is ringing, press to silence the handset ringer temporarily. While reviewing the redial list, directory or caller ID log, press to delete an individual entry. While using the dialing keys, press to delete digits, or press and hold to return to idle mode.

LCD display

Page 22

SNAPSHOT Press to take a photo shot of visitor from the doorbell during video streaming.

p/VOL+/

Press to scroll up while in a menu, or in the directory, caller ID log or redial list. Press to review the directory when the phone is not in use. While entering names or numbers, press to move the cursor to the right. During a call or message playback, press to increase the listening volume.

/VIEW

When you hear a chime, press to start video streaming. Press to extend video streaming session.

OFF/CANCEL During a call, press to hang up. While in a menu, press to return to the previous menu, or press and hold to return to idle mode, without making changes. While the phone is ringing, press to silence the handset ringer temporarily. Press and hold to erase the missed call indicator when the phone is not in use.

Press repeatedly to display other dialing options while reviewing a caller ID log entry.

REDIAL/PAUSE Press repeatedly to view the last 10 numbers dialed. While entering numbers, press and hold to insert a dialing pause.

10.

11.

12.

13.

14.

15.

Page 23

PAGEPAGE

3.2 Overview of the Base Station

/PAGE

Press to page all system handsets.

Message window Shows the number of messages, and other information of the answering system or telephone base.

IN USE light Flashes quickly when there is an incoming call. Flashes when another telephone sharing the same line is in use. On when the telephone line is in use.

DOORBELL light On when a doorbell is in a video streaming session. Flashes quickly when the doorbell is being pressed.

/ANS ON/OFF

Press to turn the answering system on or off.

Page 24

X/DELETE Press to delete the playing message. Press twice to delete all old messages when in idle.

+/VOL/-

Press to adjust the listening volume during a call or message playback. Press to adjust the telephone base ringer volume when the phone is not in use.

/SKIP

Press to skip to the next message.

/REPEAT Press to repeat the playing message. Press twice to play the previous message.

/PLAY/STOP Press to play messages Press to stop playing messages.

10.

Page 25

3.3 Overview of the Doorbell

Camera lens

Infrared LEDs

Backup light for night vision.

Doorbell light Flashes when /DOORBELL is pressed.

/DOORBELL

Press to send a chime to the telephone base and capture a photo.

Page 26

3.4 Handset LCD Display Icons and Symbols

The screen display gives you information on the current status of the telephone.

Display icons Description: Icons can be on (visible), or Flashing or Off

(not visible)

Battery is low; place handset in charger to recharge.

Full battery power level.

2/3 battery power level.

1/3 battery power level.

High level of video signal reception strength.

Medium level of video signal reception strength.

Low level of video signal reception strength.

The handset speakerphone in use.

On if the doorbell is ringing.

On steadily if the handset ringers are turned off.

There are new message recorded by the answering machine.

There are new voicemail received from the telephone service provider.

MIC OFF

Microphone is muted.

ANS ON

The answering machine is turned on.

Page 27

3.5 Handset Menu Structure

In idle mode, press MENU to enter the menu. Refer to the following table for the menu structure.

Main Menu Play msgs AnsweringSys Directory

Sub menu Play new

messages

Play old messages

Announcement

Delete all old

Record memo

Answer ON/OFF

Ans sys setup

Review

Add contact

Speed dial

Caller ID log Photo log Ringers Chime

View

Del all calls

View/Doorbell X

Delete all

Ringer volume

Ringer tone

Chime volume

Chime tone

Key Press

Date & Time Settings

LCD language

Rename devices

LCD brightness

Dim mode

Wallpaper

Voicemail #

Clr voicemail

Key tone

Dial mode

Flash time

Call divert

Doorbell setup

Page 28

4. PHONE SETTINGS

4.1 Handset Ringer Volume

You can set the ringer volume or turn the ringer off on each handset. When the ringer is off, the handset displays .

Press MENU →

→ Ringers

Press SELECT → Ringer volume

Press SELECT →

→ (The desired volume level).

Press SET.

-OR-

Press OFF → turn off the ringer → SET.

note The ringer volume also determines the ringer volume for intercom calls. When the ringer is set to off, that handset is silenced for all incoming calls except paging tone.

4.2 Telephone Base Ringer Volume

Press +VOL / VOL- on the right side of telephone base – adjust the ringer volume when the telephone base is not in use.

When you set the ringer volume to silent, the base ringer is off and the system announces, “Base ringer is off.”

4.3 Ringer tone

You can choose from different ringer tones for each handset.

Press MENU →

→ Ringers

Press SELECT →

→ Ringer tone,

Press SELECT →

→ (The desired ringer tone).

Press SELECT.

note If you turn off the ringer volume, you will not hear ringer tone samples.

Page 29

4.4 Chime Volume

You can adjust the telephone base or handset chime volume level, or turn the

chime off.

Press MENU →

→ Chime.

Press SELECT → Chime volume

Press SELECT →

→ Local handset / Base

Press SELECT →

→ (The desired volume level).

Press SET.

-OR-

Press OFF → turn off the chime → SET.

4.5 Chime Tone

You can choose from different chime tones for the telephone base or handset.

Press MENU →

→ Chime.

Press SELECT →

→ Chime tone.

Press SELECT →

→ Local handset / Base

Press SELECT →

→ (The desired chime tone).

Press SET.

4.6 Quiet Mode

You can turn on the quiet mode for a period of time (1-12 hours). During this period, all tones (except paging tone and chime), Caller ID Announce and call screening are muted.

When you turn on the quiet mode, the answering system turns on automatically. When the quiet mode duration expires, the answering system remains on.

To set the quiet mode duration:

Press and hold .

Press

→ (The desired duration).

Press SET.

The handset displays Answering system and chime tone is ON during quiet mode and then returns to idle. The handset displays ANS ON, and quiet.

Page 30

To turn off the quiet mode:

Press and hold .

The handset displays Quiet mode is OFF briefly. You hear a conrmation tone and the handset returns to idle.

note

If you change the settings of the ringer tone, handset ringer volume or telephone base ringer volume while the quiet mode is on, you can still hear the samples of them.

4.7 Set Date and Time

The answering system announces the date and time of each message prior to playing it. Before using the answering system, set the date and time as follows.

Press MENU →

→ Date & Time

Press SELECT →

→ Enter the month, date & year.

Press SET →

→ Enter the hour & minute.

Press SET.

notes

If the date and time are not set when a message is recorded, the system announces, “Time and date not set,” before each message plays.

The telephone plays two beeps if you enter an invalid number.

4.8 LCD language

You can choose your desired language to be displayed on LCD.

Press MENU →

→ Settings

Press SELECT → LCD language.

Press SELECT →

→ (The desired language).

Press SET.

5. Press YES.

•

Page 31

4.9 Rename Devices

You can create a name for each handset and doorbell. The new name can be up

to 11 characters.

Press MENU →

→ Settings

Press SELECT →

→ Rename devices.

Press SELECT →

→ Local handset / Doorbell

Press SELECT.

Use the dialing keys to edit the name

Press DELETE / BACKSP → erase a character.

Press and hold DELETE → erase all characters.

Press

→ move the cursor to the right or to the left.

6. Press SAVE.

4.10 LCD Brightness

You can adjust the screen brightness of your handset to optimize readability

lighting conditions.

Press MENU →

→ Settings

Press SELECT →

→ LCD brightness.

Press SELECT →

→(The desired brightness level).

Press SET.

4.11 Dim Mode

You can set the handset backlight in dim mode or completely off when it is not in use.

Press MENU →

→ Settings

Press SELECT →

→ Dim mode.

Press SELECT →

→ On / Off.

Press SET.

•

Page 32

4.12 Wall Paper

You can set the wallpaper for your handset.

Press MENU →

→ Settings

Press SELECT →

→ Wallpaper.

Press SELECT →

→ (The desired each wallpaper).

Press SET.

4.13 Clear Voicemail Indicators

If you subscribe to voicemail service offered by your telephone service provider, New voicemail and

display on the handset when you have new voicemail messages. Contact your telephone service provider for more information and assistance about using your voicemail service.

After you have listened to all new voicemail messages, the indicators on the handset turn off automatically.

Use the clear voicemail feature when the telephone indicates that there is new voicemail but there are none (for example, when you have accessed your voicemail while away from home). Clearing the voicemail waiting indicator only turns off the indicators; it does not delete your voicemail messages. As long as you have new voicemail messages, your telephone service provider continues to send the signal to turn on the indicators.

To manually turn off the new voicemail indicators:

Press MENU →

→ Settings

Press SELECT →

→ Clr voicemail

Press SELECT.

Press YES.

note Your telephone service provider may alert you of new messages with a stutter (broken) dial tone. Contact your telephone service provider for details.

Page 33

4.14 Key Tone

You can adjust the volume level of key tone, or turn it off for each handset. If you

turn the key tone off, there are no beeps when you press the handset keys.

Press MENU →

→ Settings

Press SELECT →

→ Key tone.

Press SELECT →

→ (The desired volume level).

Press SET.

4.15 Dial Mode

The dial mode settings is country dependent. Please contact your local service provider for the correct settings.

Press MENU →

→ Settings

Press SELECT →

→ Dial Mode.

Press SELECT →

→ (The desired dial mode).

Press SET.

4.16 Flash Time

The ash time settings is country dependent. Please contact your local service

provider for the correct settings.

Press MENU →

→ Settings

Press SELECT →

→ Flash Time.

Press SELECT →

→ (The desired ash time).

Press SET.

4.17 Call Divert

You can divert a doorbell call to an external number. The telephone base will call directly to the destination number during doorbell ringing.

To set call divert on:

Press MENU →

→ Settings

Press SELECT →

→ Call divert.

Press SELECT →

→ On.

Press SET → Enter destination number.

Page 34

Press NEXT → Enter the PIN (default: 0000).

If destination number has been set before, the screen displays the current destination number. You can press CLEAR to clear the current number and enter a new destination number, then press NEXT.

6. Press SAVE..

To set call divert off:

Press MENU →

→ Settings

Press SELECT →

→ Call divert.

Press

→ Off.

Press SET.

-OR-

Press and hold to set call divert off when the telephone is not in use. The screen displays Call divert OFF. You hear a conrmation tone and the call divert icon disappears.

•

Page 35

5. USING THE DOORBELL

5.1 Answer a Chime

When /DOORBELL is pressed, you hear a chime. The doorbell automatically captures a photo of the visitor.

Press SPEAK → Answer the chime.

notes

Only one handset can answer the chime and start a video streaming session.

If you have more than two handsets, only the first two registered handsets display the photo.

The video streaming ends after 30 seconds.

Press OFF to silence the chime.

Only one doorbell can perform video streaming session at a time. If other doorbell is pressed, you hear a chime, but no handsets can answer.

When call divert is set to on:

Only the telephone base plays a chime tone and the handsets display Call divert is in progress. The telephone base calls to the destination number. For call

divert setting, see Call Divert section.

Enter the PIN on the destination phone → Answer the doorbell call.

Press OFF / – End the doorbell call.

notes

If you do not press OFF or to end the doorbell call. busy tone will be heard on the doorbell side.

When the screen displays the Call divert is in progress message, other messages such as xx Missed calls will be hidden.

•

Page 36

5.2 Start a Video Streaming Session

When /DOORBELL is pressed and you hear a chime on the handset, press /VIEW / VIEW.

notes

If you do not press the flashing SPEAK during the video streaming, the session ends in 2 minutes.

-OR-

Press /VIEW when the handset is not in use

note

If you have more than one doorbell, press

to scroll to the desired doorbell

and then press SELECT.

-OR-

Press /VIEW during a call. The call is put on hold and other system handsets display Line on hold. You hear a beep every 10 seconds.

note

If you do not press the flashing SPEAK during the video streaming, the session ends in 2 minutes.

Options while video streaming:

Press the ashing SPEAK → talk to the visitor.

Press SNAPSHOT – take a photo shot of the visitor.

Press ISO → + / - – adjust the video stream brightness.

note After you press SPEAK to start a conversation with the visitor, the video/audio streaming session ends in 45 seconds if it is initiated by the doorbell or 60 seconds if initiated by the handset.

•

Page 37

5.3 Extend a Video Streaming Session

The video/audio streaming session ends in 45 seconds if it is initiated by the doorbell or 60 seconds if initiated by the handset. When the screen displays

Session is ending... Press [VIEW] to extend. and /VIEW ashes, you have ve seconds to extend the video session,

Press /VIEW – extend the video session.

If you did not press SPEAK during the video session, the video streaming extends for 30 seconds if it is initiated by the doorbell, or for 120 seconds if initiated by the handset.

If you pressed SPEAK during the video session, the video streaming extends for 45 seconds if it is initiated by the doorbell, or for 60 seconds if initiated by the handset.

5.4 End a Video Streaming Session

Press OFF.

-OR-

Place the handset back in the telephone base.

5.5 Answer an Incoming Call During Video Streaming

If you receive an outside call during a video streaming session, there is an alert tone.

To answer the outside call, press on the handset. The video streaming session ends automatically.

To end the video streaming session without answering the outside call, press

OFF. The video streaming session ends and the telephone continues to ring.

5.6 View Captured Photos

The telephone stores up to 100 photos captured by the doorbell.

Press /VIEW.

Press SELECT →

→ browse through the photo log.

5.7 Delete a Captured Photo

When the desired photo displays, press DELETE.

•

Page 38

5.8 Delete All Captured Photos

Press /VIEW.

Press

→ Delete all

Press SELECT.

Press YES.

5.9 Night Vision

To help you carry out the video streaming session at night, the doorbell automatically uses the light from its infrared LEDs for transmitting images to the handset unit when the surrounding is dark. However, it only transmit black-andwhite images.

Page 39

6. USING THE PHONE

6.1 Make a Call

Enter telephone number. Press / .

6.2 Answer a Call

Press / / any dialing key (0-9, or ).

6.3 End a Call

Press OFF.

-OR-

Place the handset back in the telephone base.

6.4 Handsfree

During a call, press on the handset to switch between the speakerphone and normal handset use.

6.5 Volume Control

During a call:

Press p/VOL- / q/VOL+ – adjust the listening volume.

notes

The handset earpiece and speakerphone volume settings are independent.

When the volume reaches the minimum or maximum setting, you hear two beeps.

•

Page 40

6.6 Mute

The mute function allows you to hear the other party but the other party cannot hear you.

During a call, press MUTE on the handset. The screen briey displays Microphone off, then displays MIC OFF until the mute function is turned off.

Press MUTE on the handset to resume the conversation. The screen briefly

displays Microphone on.

6.7 Call Waiting

If you subscribe to call waiting service from your telephone service provider, you hear a tone if someone calls while you are already on a call.

Press /FLASH – put the current call on hold and take the new call.

Press /FLASH – switch back and forth between calls.

6.8 Temporary Ringer Silencing

When the telephone is ringing, you can temporarily silence the ringer of the handset or the telephone base without disconnecting the call. The next call rings normally at the preset volume.

To silence the handset ringer:

Press CANCEL, MUTE or SILENCE on the handset, the handset displays Ringer muted briey then displays.

To silence the telephone base ringer:

Press VOL- on the telephone base.

The handset and the telephone base ring when there is an incoming call unless the ringer volume setting on that device is turned off.

•

Page 41

6.9 Temporary Tone Dialing

If you have pulse (rotary) service only, you can switch from pulse to touch-tone dialing temporarily during a call. This is useful if you need to send touch-tone signals to access your telephone banking or long distance services.

During a call, press on the handset.

Use the dialing keys to enter the number you wish to dial. The telephone sends touch-tone signals. It automatically returns to pulse dialing mode after you end the call.

6.10 Chain Dialing

Use this feature to initiate a dialing sequence from numbers stored in the directory, caller ID log or redial list while you are on a call using the handset.

Chain dialing can be useful if you wish to access other numbers (such as bank account numbers or access codes) from the directory, caller ID log or redial list.

To access a number from the directory while on a call with the handset:

Press OPTION → Directory.

Press SELECT →

→ (The desired entry).

Press DIAL.

To access a number from the caller ID log while on a call with the handset:

Press OPTION.

Press

→ Caller ID log

Press SELECT →

→ (The desired entry).

Press DIAL.

To access a number from the redial list while on a call with the handset:

Press REDIAL.

Press

→ (The desired entry).

Press DIAL.

note

Press CANCEL to exit the directory, caller ID log or redial list when you are on a call.

Page 42

6.11 Find Handset

This feature helps you nd the misplaced handset(s).

To start the paging tone:

Press /PAGE on the telephone base. All idle handsets ring and their screens display ** Paging **.

To stop the paging tone:

Press /PAGE on the telephone base.

-OR-

Press , , CANCEL or any dialing key (0-9, or ) on a handset.

-OR-

Place the handset in the telephone base.

note Press MUTE or SILENCE to turn off the ringer of that handset. Its screen briefly

shows Ringer muted and displays .

6.12 Redial

Each handset stores the last 10 telephone numbers dialed (up to 30 digits). When there are already 10 entries, the oldest entry is deleted to make room for the new entry.

To review and dial a redial number:

Press REDIAL.

Press

→ (The desired entry).

Press / .

-OR-

Press / .

Press REDIAL.

Press

→ (The desired entry).

Press DIAL.

•

Page 43

To delete a redial number:

Press REDIAL.

Press

→ (The desired entry).

Press DELETE.

6.13 Equalizer

The equalizer feature on the handset enables you to change the quality of the handset audio to best suit your hearing. While on an outside call or an intercom, press EQ repeatedly to select the equalizer setting Treble 1, Treble 2, Bass or Natural (the default setting) for the handset.

note The current equalizer setting remains unchanged until a new setting is selected.

Page 44

7. DIRECTORY

The home directory stores up to 50 entries with up to 30 digits for each phone number and 15 characters for each name.

7.1 Create a New Entry in the Directory

Press MENU →

→ Directory.

Press SELECT →

→ Add contact

Press SELECT → Enter number.

Press

– move the cursor to the left or right.

Press DELETE / BACKSP – erase a digit.

Press and hold DELETE – erase all digits.

Press and hold PAUSE – enter a dialing pause (a P appears).

4. Press NEXT to move on to the name.

5. Enter the name.

Press

– move the cursor to the left or right.

Press 0 – add a space.

Press DELETE / BACKSP – erase a character.

Press and hold DELETE – erase all characters.

6. Press SAVE.

•

Page 45

7.2 Add a Predialled/Redial List Number to the Directory

You can save a predialled number or redial list number to the directory.

Enter a number. Press SAVE.

Press

– move the cursor to the left or right.

Press DELETE / BACKSP – erase a digit.

Press and hold DELETE – erase all digits.

Press and hold PAUSE – enter a dialing pause (a P appears).

Press NEXT.

Enter the name.

Press

– move the cursor to the left or right.

Press 0 – add a space.

Press DELETE / BACKSP – erase a character.

Press and hold DELETE – erase all characters.

Press SAVE.

7.3 View the Directory

Entries are sorted alphabetically.

Directory entries appear alphabetically.

Press .

Press

-OR-

Press MENU →

→ Directory

Press SELECT → Review.

Press SELECT.

Press

•

Page 46

7.4 Dial, Edit or Delete a Directory

7.4.1 Dial a Directory Entry

You can dial a directory entry on any line.

To dial a directory entry:

Search for the desired entry in the directory.

Press / .

7.4.2 Edit a Directory Entry

Search for the desired entry in the directory.

Press EDIT. Edit the name.

Press

– move the cursor to the left or right.

Press DELETE or BACKSP – erase a digit.

Press and hold DELETE – erase all digits.

Press and hold PAUSE – enter a dialing pause (a P appears).

3. Press NEXT. Edit the number.

Press

– move the cursor to the left or right.

Press DELETE / BACKSP – erase a character.

Press and hold DELETE – erase all characters.

4. Press SAVE.

7.4.3 Delete a Directory Entry

To delete an entry:

Search for the desired entry in the directory.

Press DELETE.

Press YES.

note

Once a directory entry is deleted, it cannot be retrieved.

•

Page 47

7.5 Speed Dial

7.5.1 Assign a Speed Dial Directory Entry

You can assign 9 of your directory entries to a speed dial slot (0, 2-9). The speed dial entries are shared by all handsets.

Up to 9 speed dial entries can be stored. The speed dial number must be created from an existing entry in the directory.

Press MENU →

→ Directory.

Press SELECT →

→ Speed dial.

Press SELECT →

→ (The desired speed dial location).

4. Press ASSIGN.

5. Press

→ (The desired entry in the directory).

6. Press ASSIGN.

7.5.2 View the Speed Dial Directory

Press MENU →

→ Directory.

Press SELECT →

→ Speed dial.

Press SELECT →

7.5.3 Dial a Speed Dial Entry

When idle, press and hold the dialling key (0, 2-9) corresponding to the assigned entry you wish to call.

7.5.4 Reassign a Speed Dial Entry

Press MENU →

→ Directory.

Press SELECT →

→ Speed dial.

Press SELECT →

→ (An occupied speed dial location).

Press VIEW →

(Th desired speed dial entry).

5. Press REPLACE.

6. Press YES.

Page 48

7.5.5 Delete a Speed Dial Entry

Press MENU →

→ Directory.

Press SELECT →

→ Speed dial.

Press SELECT →

→ (An occupied speed dial location).

Press DELETE / DELETE.

Press YES.

note:

Deleting speed dial entries does not affect the directory entries

Page 49

8. CALLER ID LOG

8.1 Caller ID

If you have subscribed to Caller ID service, you will be able to see your caller’s number on your handset display (provided it is not blocked) prior to answering the call. If your caller’s name is stored in the directory and a number match is found, you will see the caller’s name on the display instead.

Your phone can store up to 50 answered calls and unanswered with date/time information in the caller ID log.

note

If the phone number has more than 24 digits, it will not be saved or shown in the caller ID log.

Missed calls are marked with XX Missed call(s). Each time you review a caller ID log entry marked with NEW, the number of missed calls decreases by one. When you have reviewed all the missed calls, the missed calls indicator no longer shows. You can review, redial, and copy an entry into the directory. Entries appear in reverse chronological order.

8.1.1 View the Caller ID Log

Review the calling number display history to nd out who called, to easily return

a call, or to copy the caller’s name and number into your directory. Caller ID log empty appears if there are no records in the caller ID log.

Press CID.

Press

-OR-

Press MENU →

→ Caller ID log

Press SELECT → Review.

Press SELECT.

Press

note

Only one handset can review the calling number display history at time. If another handset tries to enter the directory or calling number display history, it shows Not available at this time.

Page 50

8.1.2 Dial a Caller ID Log Entry

Search for the desired entry in the caller ID log.

Press / .

8.1.3 Save a Caller ID Log Entry to the Directory

Caller ID log entries can only be saved to the Home directory.

Select a desired entry in the caller ID log.

Press SAVE. Edit the number.

Press

– move the cursor to the left or right.

Press DELETE / BACKSP – backspace and erase a digit.

Press and hold DELETE – erase the entire entry.

Press and hold PAUSE – insert a dialing pause (a P appears).

3. Press NEXT. Edit the name.

Press

– move the cursor to the left or right.

Press DELETE / BACKSP – erase a character.

Press and hold DELETE – erase all characters.

4. Press SAVE.

notes

When you try to save a caller ID log entry without any calling number display information, the handset displays Unable to save.

When you try to save a number already stored in the directory, the screen shows Number already saved.

8.1.4 Delete a Single Entry in the Caller ID Log

Select a desired entry in the caller ID log.

Press DELETE.

8.1.5 Delete the Entire Caller ID Log

Press MENU →

→ Caller ID log

Press SELECT →

→ Del all calls.

Press SELECT.

Press YES.

•

Page 51

8.1.6 Caller ID Log Screen Messages

Displays: When:

Private name

The caller is blocking the name.

Private number

The caller is blocking the telephone number.

Private caller

The caller is blocking the name and number.

Unknown name

This caller’s name is unavailable.

Unknown number

This caller’s number is unavailable.

Unknown caller

No information is available about this caller.

Long distance or L (before the caller’s

number)

It is a long distance call.

Page 52

9. ANSWERING MACHINE

Use the answering system menu of a cordless handset to turn on or off the answering system or message alert tone, set up the outgoing message, activate the call screening, or change the number of rings, remote access code or message recording time.

9.1 Answer On/Off

If you turn the answering system on, it answers calls and records messages only on the home line. If your paired mobile phone has voicemail, callers can leave messages with that voicemail service.

If your answering system is turned off and you change any of its settings, the answering system automatically turns on again and the handset displays Calls will be answered.

When the answering system is turned on, the ANS ON light on the telephone base is on and the handsets display ANS ON.

To turn the answering system on or off:

Press /ANS ON/OFF on the telephone base to turn the answering system on or off. When the answering system is turned on, it announces, “Calls will be answered. “The telephone base screen displays Calls will be answered. When the answering system is turned off, it announces, “Calls will not be answered. “The telephone base screen displays Calls will not be answered.

Press MENU →

→ AnsweringSys

Press SELECT →

→ Answer ON/OFF

Press SELECT →

→ On/ Off

Press SET.

Page 53

9.2 Outgoing Messages

An outgoing message is the greeting callers hear when calls are answered by the answering system.

9.2.1 Play Your Outgoing Messages

Press MENU →

→ AnsweringSys

Press SELECT → Announcement.

Press SELECT →

→ Answer & record / Answer only.

Press SELECT.

Press PLAY.

9.2.2 Record Your Own Outgoing Messages

You can record an outgoing message up to 90 seconds, but any outgoing

message shorter than two seconds will not be recorded.

Press MENU →

→ AnsweringSys

Press SELECT → Announcement.

Press SELECT →

→ Answer & record / Answer only.

Press SELECT.

Press RECORD.

After the tone, speak towards the microphone.

Press STOP.

notes

Your outgoing message can be up to 120 seconds in length. Outgoing messages shorter than two seconds are not recorded.

9.2.3 Delete Your Outgoing Messages

Press MENU →

→ AnsweringSys

Press SELECT → Announcement.

Press SELECT →

→ Answer & record / Answer only.

Press SELECT.

Press PLAY.

Press RESET.

Press YES.

•

Page 54

9.3 Message Playback

If you have both new and old messages, you can play either new or old messages. The calling number display information displays on the screens when you play messages and you can call back the caller.

To listen to messages with the telephone base:

Press /PLAY when the phone is not in use.

Options during playback:

Press VOL- / VOL+ – adjust the message playback volume.

Press /SKIP – skip to the next message.

Press /REPEAT – repeat the message. Press /REPEAT twice – listen to the previous message.

Press X/DELETE – delete the playing message.

Press /STOP – stop the playback.

To listen to messages with a handset:

Press MENU → Play msgs.

Press SELECT. If you have either new or old messages, the messages play automatically. If you have both new and old messages:

To play new messages, press SELECT.

To play old messages, press

→ Play old msgs → SELECT.

Options during playback:

Press VOL+ / VOL- – adjust the message playback volume. Press SKIP – skip to the next message.

Press REPEAT – repeat the message. Press REPEAT twice – hear the previous message.

Press – switch between the speakerphone and the handset earpiece.

Press DELETE – delete the playing message.

Press OFF – stop the playback.

note

Only one device can access the answering system at a time.

•

Page 55

9.4 Delete All Old Messages

Using the telephone base:

Press X/DELETE.

Press X/DELETE again.

Using a handset or the telephone base:

Press MENU →

→ AnsweringSys

Press SELECT →

→ Delete all old

Press SELECT

Press YES.

note

You can only delete old messages, which are messages you have previously reviewed.

9.5 Record and Play Memos

Memos are messages you record as reminders for yourself or others using the same answering system. You can record your own memos using a system handset or the base. Play and delete them the same way as incoming messages.

To record a memo:

Press MENU →

→ AnsweringSys

Press SELECT →

→ Record memo.

Pess SELECT.

After the tone, speak towards the microphone.

Press STOP to stop recording.

notes

The system announces “Memory is full,” if you attempt to record a memo when the memory is full.

Each memo can be up to 4 minutes in length.

Memos shorter than 2 seconds are not recorded.

•

Page 56

9.6 Answering Machine Settings

in the answering system setup menu, you can change the settings for answer mode, call screening, number of rings, remote access code, message alert tone and recording time.

9.7 Call Screening

By default, the answer machine is set in Answer & Record mode which allows callers to leave a message. This mode can be changed to Answer only which does not allow callers to leave a message. In that case, your callers will be prompted to call back later.

To turn call screening on or off:

Press MENU →

→ AnsweringSys

Press SELECT →

→ Ans sys setup.

Press SELECT → Answer mode.

Press SELECT →

→ Answer & Record / Answer only.

Press SELECT.

9.8 Call Screening

The call screening feature lets you listen at the telephone base to a caller leaving a message. While monitoring an incoming message, you can answer the call by

pressing or on the handset.

To turn call screening on or off:

Press MENU →

→ AnsweringSys

Press SELECT →

→ Ans sys setup.

Press SELECT →

→Call screening.

Press SELECT →

→ On / Off.

Press SET.

Page 57

9.9 Number of Rings

When the answering system is turned on, it answers all incoming home calls after the number of rings set. You can choose from 2, 3, 4, 5, or 6 rings; or time saver. With time saver selected, the answering system answers after 2 rings when you have new messages, and after 4 rings when you have no new messages. This enables you to check for new messages and avoid paying unnecessary long distance charges if you are calling from out of your local area.

To set the number of rings:

Press MENU →

→ AnsweringSys

Press SELECT →

→ Ans sys setup.

Press SELECT →

→ # of rings.

Press SELECT →

→(The desired number of rings).

Press SET.

note

If you set the number of rings for the answering system as 2 or 3 rings, the Caller ID Announce feature may not have enough time to announce the caller’s full information.

9.10 Remote Access Code

A 2-digit security code is required to access the answering system remotely from any touch-tone telephone. The preset code is 00. You can change the code to any number from 00 to 99.

To change the remote access code:

Press MENU →

→ AnsweringSys

Press SELECT →

→ Ans sys setup.

Press SELECT →

→ Remote code.

Press SELECT.

Enter the 2-digit number (default: 0000)

Use the dialing keys to enter a two-digit number.

Press

– move the cursor to the left or right.

Press DELETE – BACKSP to erase a digit.

Press and hold DELETE – erase all digits.

7. Press SAVE.

•

Page 58

9.11 Message Alert Tone

When the message alert tone is set to On, the telephone base beeps every 10 seconds to alert you to new messages. The tone stops when all new messages have been reviewed.

To change the setting:

Press MENU →

→ AnsweringSys

Press SELECT →

→ Ans sys setup.

Press SELECT →

→ Msg alert tone.

Press SELECT →

→ On / Off.

Press SET.

notes

You cannot set the message alert tone when another handset or the telephone base is accessing the answering system.

The message alert tone beeps only if all the conditions below are met.

> Answering system is on.

> Message alert tone setting is on.

> There are new messages.

9.11.1 Temporarily Turn Off the Message Alert Tone

If the message alert tone is turned on, the telephone base beeps every 10 seconds when there are new messages. Pressing any telephone base key (except /PAGE) temporarily silences the message alert tone.

9.12 Recording Time

You can set the recording time limit for each incoming message.

To change the setting:

Press MENU →

→ AnsweringSys

Press SELECT →

→ Ans sys setup.

Press SELECT →

→ Recording time.

Press SELECT →

→ (The desired recording time).

Press SET.

•

Page 59

9.13 Answering System and Voicemail

Your telephone has separate indicators for two different types of voice messages: those recorded on its built-in answering system and those recorded in your service provider’s voicemaiI (fees may apply). Your telephone’s built-in answering system messages and voicemail messages are separate. Each alerts you to new messages differently.

If and XX New messages display on the telephone base and handsets, there are new messages in the built-in answering system. To listen to messages recorded on your digital answering system, press /PLAY/STOP on the telephone base.

If and New voicemail display on telephone base and handsets, your telephone service provider is indicating that it has new voicemaiI for you. To listen to your voicemail, you typically dial an access number provided by your telephone service provider, followed by a security code or PIN.

Some service providers bundle or combine multiple services like voicemail and call waiting, so you may not be aware that you have voicemail. To check what services you have and how to access them, contact your telephone service provider.

To use your voicemail service rather than your answering system, turn off your answering system. To use your answering system rather than your voicemail service, contact your telephone service provider to deactivate yourvoicemaiI service.

9.13.1 Using the Answering System and Voicemail Together

You can also use your telephone answering system and voicemail together by setting your built-in answering system to answer before voicemail answers as described below. To learn how to program your voicemaiI settings, contact your telephone service provider. Then, if you are on a call, or if the answering system is busy recording a message and you receive another call, the second caller can leave a voicemail message.

Set your answering system to answer calls at least two rings earlier than your voicemaiI is set to answer. For example, if your voicemail answers after six rings, set your answering system to answer after four rings. Some voicemail providers may program the delay before answering calls in seconds instead of rings. In this case, allow six seconds per ring when determining the appropriate setting.

Page 60

9.13.2 Message Capacity

The answering system can record and store up to 99 messages. Each message can be up to 3 minutes in length depending on the message length set. The total storage capacity for the outgoing messages and memos is approximately 15 minutes. The actual recording time depends on individual message characteristics. Messages remain available for replay until you delete them.

9.13.3 Voice Prompts

The system provides voice prompts to guide you through the setup procedures at the telephone base, message playback, remote access and recording outgoing messages.

9.13.4 Call Screening at the Telephone Base or Handset

To screen a call at the telephone base:

If the answering system and call screening are on, the outgoing messages and the incoming message broadcast at the telephone base while the call is answered by the answering system.

Options while a message is being recorded:

Press +VOL / VOL- – adjust the call screening volume.

Press +VOL – temporarily turn on the call screening if the call screening is set to off.

Press /PLAY/STOP – temporarily turn on or off the call screening.

To screen a call at the handset

If the answering system is on and recording a message, press SCREEN to screen the call on your handset and the screen displays the caller ID information. If you do not subscribe to caller ID service, the handset shows Incoming call.

Options while a message is being recorded:

Press VOL- or VOL+ – adjust the call screening volume.

Press – switch between the speakerphone and the handset earpiece.

note

The call screening setting on the base does not affect the call screening on the handset.

•

Page 61

9.13.5 Call Intercept

When a caller is leaving a message on your answering system, you can stop recording and talk to the caller by pressing / on the handset.

9.14 Remote Access

You can access the answering system remotely by dialling your home telephone number from any touch-tone telephone.

9.14.1 Remotely Access the Answering System

Dial your telephone number from any touch-tone telephone.

When the system plays your outgoing messages, enter the 2-digit remote access code (00 is the preset code).

You can also enter the remote commands (see Remote commands below).

Hang up or press 8 to end the call and save all undeleted messages.

9.14.2 Remote Commands

1 Press to listen to all messages.

2 Press to listen to new messages only.

3 Press to delete the current message (during playback).

33 Press twice to delete all old messages.

4 Press to repeat the current message (during playback).

5 Press to stop.

* 5 Press to listen to a list of remote commands.

6 Press to skip to the next message (during playback).

* 7 Press to record a new outgoing message.

8 Press to hang up the call.

0 Press to turn the answering system on or off.

Page 62

notes

If you do not press any keys after you enter the remote access code, all new messages play. If there are no new messages, all old messages play.

Once the new messages have played, the telephone announces the help menu options. If you do not press any key within 20 seconds, the remote access call automatically disconnects.

When the answering system is turned off, the telephone answers after 10 rings, and announces, “Please enter your remote access code.”

When the memory is full, the answering system answers incoming calls after 10 rings and announces, “Memory is full. Enter the remote access code.”

•

Page 63

10. TROUBLESHOOTING

If you have difculty with your phone, please try the suggestion listed below.

Problem Solutions

My telephone does not work at all.

Make sure the batteries are installed and charged correctly. For optimum daily performance, return the handset to the telephone base after use.

Make sure the power adapter is securely plugged into an outlet.

Make sure the telephone line cord is plugged rmly into the telephone base and the telephone wall jack.

Unplug the electrical power to the telephone base. Wait for approximately 15 seconds, then plug it back in. Allow up to one minute for the handset and telephone base to synchronize.

Remove and re-insert the batteries. If that still does not work, it might be necessary to purchase new batteries.

Disconnect the telephone base from the telephone

wall jack and plug in a working telephone. If the other

telephone does not work, the problem is probably in the wiring or the telephone service. Call your telephone service provider.

•

Low battery shows on screen.

Place the handset in the telephone base for recharging.

Remove and re-install the batteries and use it until fully depleted, then recharge the handset in the telephone base.

If the above measures do not solve the problem, replace the batteries.

•

The batteries do not charge in the handset or the handset batteries do not accept charge.

Make sure the handset is placed in the telephone base correctly.

Remove and reinstall the batteries, then charge for up to 16 hours.

Purchase new batteries.

•

Page 64

There is interference during a telephone conversation. My calls fade out when I am using the handset.

The handset may be out of range. Move it closer to the telephone base.

If you subscribe to high-speed Internet service (digital subscriber line - DSL) through your telephone

line, you must install a DSL lter between the telephone base and the telephone wall jack. The lter

prevents noise and caller ID problems caused by DSL interference. Please contact your DSL service

provider for more information about DSL lters.

Appliances or other cordless telephones plugged into the same circuit as the telephone base can cause interference. Try moving the appliance or telephone base to another outlet.

Other electronic products may cause interference to your cordless telephone. Install your telephone as far away as possible from the following electronic devices: wireless routers, radios, radio towers, pager towers, cellular telephones, digital telephones, intercoms, room monitors, televisions, VCRs, personal computers, kitchen appliances, and other cordless telephones.

If your telephone is plugged in with a modem or a surge protector, plug the telephone (or modem/surge protector) into a different location. If this doesn’t solve the problem, re-locate your telephone or modem farther apart from each other, or use a different surge protector.

The location of your telephone base can impact the performance of your cordless phone. For better reception, install the telephone base in a centralized

location within your home or ofce, away from

walls or other obstructions. In many environments, elevating the telephone base improves overall performance.

Disconnect the telephone base from the telephone

wall jack and plug in a corded telephone. If calls are

still not clear, the problem is probably in the wiring or telephone service. Contact your telephone service provider (charges might apply).

If the other telephones in your home are having the same problem, the problem is in the wiring or telephone service. Contact your telephone service provider (charges may apply).

•

Page 65

There is no chime from the doorbell when it is pressed.

Make sure you install two AA batteries and connect AC power supply to the doorbell.

The doorbell light on the doorbell flashes when the doorbell is pressed. If the light doesn’t flash, the doorbell may have run out of battery. You may need to replace new batteries.

Make sure the doorbell is registered to the telephone system.

Make sure your handset is in reception range and works probably.

Make sure the chime volume of your handset is not set to off.

If there is an incoming call when the doorbell is pressed, the handset will not respond to the chime.

When three or more system handsets are in use for a call at a time, video streaming will be disabled.

If you have more than one doorbell, make sure the other doorbell is not in use for video streaming. Only one doorbell can be used for video streaming at a time.

If the previous suggestions do not work, deregister all devices and register them to the telephone base again.

•

Common cure for electronic equipment.

If the telephone is not responding normally, put the handset in the telephone base. If it does not respond, try the following (in the order listed):

Disconnect the power to the telephone base. Disconnect the batteries on the handset. Wait a few minutes before connecting power to the

telephone base. Re-install the batteries and place the handset in the

telephone base. Wait for the handset to synchronize with the

telephone base. Allow up to one minute for this to take place.

•

This telephone is not equipped with a grounding function. Therefore, some of the functions may be limited when used in PBX systems. Please contact the technical support of the network provider for further information.

Page 66

Vtech Product Warranty

Dear Customer, Thank you for purchasing a VTech telephone. For the product warranty applicable to this product, we refer you to the VTech website www.euphones.vtech.com for on line registration. Your retailer will provide you

with a statutory 2-year warranty. If you have a problem within the rst 2 years from

purchase, call the warranty helpline or email them.

For Extended Warranty

Please keep a copy of your proof of purchase; you will need this when presenting the product back to where you bought it from.

If you have a problem after 2 years of purchase, up to 5 years from purchase: Within 30 days of purchase you need to have registered your device at www.euphones.vtech.com.

The following parts to your device are not covered by this extended warranty: Batteries, Cables, Damage caused by pets, Damaged caused from being dropped, Water Damage, Sun Exposure Damage.

Thank You.

11. WARRANTY

Page 67

This analog telephone DECT complies with the basic requirements contained in the R&TTE Directive 1999/5/EC on ratio equipment and telecommunications terminal equipment and is suitable for connection and operation in the member state indicated on the base station and/or packaging.

The declaration of conformity may be viewed at www.euphones.vtech.com.

The CE symbol conrms the conformity of the telephone and the above directive.

12. APPROVAL AND CONFORMITY

Page 68

13. CARE AND MAINTENANCE

Take care of your telephone

Your cordless telephone contains sophisticated electronic parts, so you must treat it with care.

Avoid rough treatment.

Place the handset down gently.

Save the original packing materials to protect your telephone if you ever need to ship it.

Avoid water

You can damage your telephone if it gets wet. Do not use the handset in the rain, or handle it with the wet hands. Do not install the telephone base near a sink, bathtub or shower.

Electrical storms

Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety, take caution when using electric appliances during storms.

Cleaning your telephone

Your telephone has a durable plastic casing that should retain its luster for many year. Clean it only with a soft cloth slightly dampened with water or a mild soap.

Do not use excess water or cleaning solvents of any kind.

note

Remember that electrical appliances can cause serious injury if used when you

are wet or standing in water. If the telephone base should fall into water. DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL. Then pull the unit out by the unplugged cords.

•

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED

BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING

TO THE INSTRUCTIONS.

Page 69

VTECH TELECOMMUNICATIONS LTD.

A member of THE VTECH GROUP OF COMPANIES.