DT39 USER MANUAL(EN)
2-Wire Video Intercom System
Read this manual carefully before using the product, and keep it well for future use.
O
1
2
3
4
5
6
DI
SW+ SW
-
O
DI
1 2 3
4
5
6
ON
1 2 3 4 5
6
DIP
Introduction
The monitor is designed with 3.9 inch screen, it provides a resolution of
800x480 pixels with high quality image display. The touch sensitiv e button
makes the operation more easily.
Parts and Function
Microphone
Power Indicator
Talk/Mon Button
LCD Screen
Touch Button
Message Indicator
Don't Disturb Indicator
Unlock Button
Mounting Hook
Connection Port
Speaker
Terminal Descripti on
L1,L2: Bus terminal
SW+,SW-: Door bell call button
connection port
DIP switches: Total 6 bits can be
configured.
Bit1~Bit5: Used to User Code
setting.
Bit6: Set to ON if the monitor is at
the end of the line or works with
DBC4S. Otherwise, set to OFF.
-2-
L1
L2
DIP
145~160 cm
Unit Mounting
Accessory contents:
Accessories include a Bracket, two 4X25 screws (use to fasten the Mounting Bracket),
2 wire connectors (use to connect with Monitor).
Installation steps:
Installation height for indoor monitor usually is 145~160cm(refer to sketch map).
Wire the cable correctly(see the later connection chapter) then hang the Monitor on
the Mounting Bracket firmly.
About Main Menu
The main menu is your starting point
for using all the applications on your
monitor. You can customize your
main menu to display applications,
logos, and languages.
Touch the screen on the right
“1,2,3,4” of any one can enter the
home page, the home menu page
will be shown as follows:
Basic Operation Instruction
Answering a Door Call
· Press CALL button on door station.The moni tor rings,and the visitor’s imag e
will be seen on screen.If nobody answ ers the call,the screen will turn off i n
30 seconds automatically.
-3-
· Press TALK/MON Button on moni-
tor, you can communicate with t he
visitor for 90 seconds.After f i nishing
communication,press TALK/MON button again to end the communication.
· During talking state, Press UNLOCK
Button to open the corresponding door
for the visitor.
DS-1 00:30
· When the monitor is in standby mode, press TALK/MON Button(or touch
Monitor ... item on main menu page), the screen can display the view of
outside. If multi door stations ar e i nst al led, touch icon,and then touch
or icon to get into the camera switch mode. You can touch Door/Camera 1/2/3/4 to monitor the door stati on or CCTV camera you want.See the
following diagrams.(Touch icon to end monitoring.)
Intercom Function
Intercom function can be initiated by any monitor when multi monitors are installed.
When the monitor is in standby mode, Touch
the screen on the right “1,2,3,4” of any one
can enter the home page, the home menu
page,there are three items: Intercom
Call..., Inner Call ..., Call Guard Unit...
Intercom Call: User in one apartment can call
other apartments in the system. t he namelist
will be created automatically by the system.
Touch a name you want on the screen, then
touch Dial icon to dial.(Note:The DI P switches
code of each monitor must set diff erent .)
Inner Call: If multi slave monitors are installed
in the same apartment, select Inner Call, all the other Monitors will ring at the
same time, whichever Monitor answers the call, conversation is started.and
the other monitors will stop ringing at the same time.(note:the DIP switches
setting of all monitors must be same. )
-4-
Call Guard unit: A Monitor can b e assigned as Guard Unit Monitor; when t he
Guard Unit Monitor answers the call, conversation with the guard person is
started.
Other Function:
1.Call Transfer function:Touch Call Transfer item on main menu page to
enter call transfer page,and then you can select the item you want.
2.Light function:Touch Light item on main m enu page to enter light function page,and then you can select t he i tem you want.
3.Playback function:Touch Playback item on main menu page to enter
playback function page,and t hen you can select the item you want.
Basic Setup Instruction
Ring Tone Setting
Select and touch Setup item on
main menu page,and then select
Ring Tune to enter setup page.
Select DS, Intercom or Door Bell
item, There are 12 pieces ring tones
can be selected.Use Inc/Dec button
to select last/next ring tone, press
Exit button to save and exit.
Ring Tune
Ring Volume
Monitor Time
Exit
DS: set the ring tone calling from
outdoor station.
Intercom: set the ring tone calling
from other apartments.
Door Bell: set the ring tone calling
from door bell.
Current:
Tune Select
01
Inc
Dec
Exit
Ring Volume Setting
Select and touch Setup on
main menu page, then select Ring
Volume... item, the setting range is
0~9. Use / button to increase
/ decrease the value, press Exit button to save and return last page.
Current:
Adjust Value
3
-5-
Monitor Time Setting
Select and touch Setup on main
menu page, then select Monitor
Time... item. Use / button to
increase / decrease the value, press
Exit button to save and return last
page.
Menu Language Setting
Current:
Adjust Value
30sec
Maximum 16 languages can be supported by the monitor.
On main menu page, select
0
About
->Language.The languages that
the monitor supported will be displayed, and the current language wil l
be shown “√ ”.
Screen Setting
During monitoring or talking stat e,
press Adjust button,the adjust
menu will be displayed.
There are 3 adjustment items can be
selected:
The first item is Scene mode se-
lection: Total 3 screen modes can be
selected in sequence: Normal,Bright
and Soft .
The Brightness item is for the
image quality setting, adjust the value
to get the best image you like.
The Volume item is for the talk
volume setting.
-6-
H/W: a1.2
S/W: 00.01.00
Addr: 00.01
Video STD: AUTO
DS-1 00:30
DS-1 00:30
Language
Restore
· Note that all the modifications will be done immediately after the operat i on.
Press button to quit the adjust page.
Restore to Default
On main menu page, select About->Restore. If touch icon ,All settings will be restored to default, if you don't want to restore, touch icon to
cancel the operation.(Note that the restore to default operation will not change
the time setting and the datas.)
H/W:
S/W:
Addr:
a1.2
00.01.00
00.01
Language
Restore
Video STD: AUTO
Installation Setting
Enter Installation Setup Page
Step1: Touch
About on main menu page ,then press UNLOCK button
and hold for 2s enter Installer Setup page.
Step2: Input 4 digits number according to the information.
Step1 Step2
InstallerSetup
[0000]
Pressunlocktoexit!
Inc
Dec
Next
Confir m
-7-
The setting items are as foll owings:
[8000]:Master 0
[8004]:Guard unit
[8006]:Panel on as slaver called
[8014]:Unlock menu on
[9006]:Simplified version
[8001]~[8003]:Slaver 1~3
[8005]:Not guard unit
[8007]:Panel off as slaver called
[8015]:Unlock menu off
[9007]:Full-featured version
How to set the monitor as a Guard Monitor
A Monitor can be assigned as Guard Uni t Monitor; when the Guard Unit Monitor answers the call, conversation with the guard person is started.
The code number of 8004 is used to set the monitor as a Guard Unit Monitor
and 8005 is used to cancel this function. (Not Guard Unit is default setting. )
How to set the slave monitor address
Maximum 4 monitors can be connected in one apartment,one master monitor together with 3 slave monitors, so y ou should set the address correctl y.
(note:must have one monitor to be set as master monitor)
The code of 8000 is used to set the ma ster monitor(by default).
The code of 8001 is used to set the first slave monitor .
The code of 8002 is used to set the sec ond slave monitor .
The code of 8003 is used to set the third slave monitor .
How to set the monitor panel on
In default mode,when receive a calling, the master and slave monitors will
ring at the same time,and just the master monitor can display the image while
the slave monitors can not.But t he set tings can be changed,you can set the
master monitor and all the slave monit ors to panel on at the same time when
receiving a call, just input the code number of 8006 on each slave monitor.
Press call button
on door station
When reveiving calling,all monitors can display the image at the same time
Master monitor
#1st slave monitor
#2nd slave monitor
#3rd slave monitor
-8-
How to set 2 locks control
The monitor can be set to control 2 lock s while you should set the unlock
menu item to “on “ state.
The code number of 8015 is used to set the unlock menu off (by default) that
it can only control one lock.
The code number of 8014 is used to set the unlock menu on that it can control
two locks.
Note:
1. During talking or monitoring stat e, press
UNLOCK button,two unlock i cons will be
shown. Select the item you want, and then
it will release the corresponding door(The
code number of 8014 is used to set the unlock menu on).
2. Note that the restore to default operation
will not change the parameters sett i ng.
DS-1 00:30
How to set the main menu version
There are two main menu version to choose for the monitor:Full-featured version and Simplified version(by def aul t) .
The code of 9006 is used to set the sim pli fied version main menu(by default).
The code of 9007 is used to set the full-featured version main menu.
Specification:
· Power Supply:
· Power Consumption:
· Monitor Screen:
· Display Resolutions:
· Video Signal:
· Wiring:
· Dimension:
DC 20-28V
Standby 0.286W; Working status 3.224W
3.9 inch digital color TFT
800(R, G, B) x 480 pixels
1Vp-p, 75Ω, CCIR standard
2 wires, non-polarity
138(H)×138(W)×19(D)mm
-9-
Precautions
1) All components should be protect ed from violence vibration. And not all ow
to be impacted, knocked and dropped.
2) Please do the cleanness with soft cotton cloth, please do not use the organic impregnant or chemical clean agent. If necessary, please use a l ittle
pure water or dilute soap water to clea n the dust.
3) Image distortion may occur if t he video monitor is mounted too close t o
magnetic field e. g. Microwaves, TV, computer etc.
4) Please keep away the monitor from wet, high temperature, dust, caustic
and oxidation gas in order to avoid any unpredictable damage.
5) Must use the right adaptor which is supplied by the manufacturer or approved by the manufacturer.
6) Pay attention to the high volt age i nside the products, please refer service
only to a trained and qualified professional.
-10-
Note
-11-
WARRANTY CARD
NB Please keep this document safe, as it is proof of your Warranty
Your Video door system comes with a one year Manufacturers Warranty. When
used normally, the following services are offered:
The following actions will void the Warranty:
1. Damage to the device during installation
2. Damage to the device through misuse
3. Opening and/or disassembling the device
4. Attempting to force the device to perform functions for which it is not intended
5. Attaching the device to power supplies other than thoserecommended by the
manufacturer
Distributor for Warranty purposes:
Intelligent Home Online Ltd
62 Hartley Old Road
Purley, Surrey
CR8 4HJ
+44 (0)20 86170015
www.intelligenthomeonline.com
Product:_____________________________________________
Purchaser Name: ______________________________________
Invoice N: ____________________________________________
Purchase Date_________________________________________
The design and specifications can be changed without notice to the user. Right to
interpret and copyright of this manual are preserved.
DT-ENG-39-V1 20140115
Loading...