vox Vox Tonelab SE VOX ToneLab SE EasyStart

`
y
t
Eas
TToonneeLLaabb SSEE
MMaaiinn FFeeaattuurreess
¾ Amp, Cabinet and Effect
modeling sounds from the popular Valvetronix-series
¾ Patented VOX Valve Reactor
tube power amp circuit using a 12AX7 in push-pull configuration
¾ 16 classic amp models ¾ 11 accurate cabinet models ¾ 50 pedal, modulation, delay
and reverb effects
¾ 2 Amp/Cab set ups per
program
¾ Up to 4 kinds of effects can
be used simultaneously in addition to the Amp and Cabinet models
¾ Knob interface for quick and
easy operation
¾ 96 Program locations ¾ 2 Expression pedals with
classic VOX chrome tops
¾ Sounds can be stored and/or
edited in a PC through MIDI IN/OUT
¾ PC Editor & librarian
provided
¾ Insert feature lets you
connect your favorite pedal
¾ Built-in Auto tuner with
calibration
¾ Reverse LCD with backlight ¾ Rugged surface parts, quality
switches and metal body
Star
AAuuddiioo CCoonnnneeccttiioonnss aanndd TTuunniinngg::
1. If connecting to headphones, mixer, recorder or powered monitors, press the Global button and then use the
up/down cursor buttons and select “LN” (LINE). Select “AP” (AMP) if connecting to a guitar amplifier (The
ToneLab SE is set to “AP” from the factory).
2. After making audio and AC connections, connect your guitar to the INPUT jack on the rear panel. If using
headphones, connect to the headphone jack on the rear panel. Lower the Level knob and turn on the power
by pressing the power switch. Raise the levels to adjust the volume.
3. Tune up! Press and hold the FX ON/OFF (TUNER) switch for 0.5 seconds. All effects will be bypassed and the
auto chromatic tuner will be active - play a note and watch the meter to tune your guitar. For silent tuning,
hold the switch down for 1.5 seconds (The name display indicates MUTE). To Exit, press the FX ON/OFF
(TUNER) switch once again and you’ll return to the previous mode.
ToneLab EasyStart
RReessttoorriinngg tthhee FFaaccttoorryy PPrreesseett PPrrooggrraammss::
1. While holding down the, Up, Down and EXIT buttons, press the STANDBY button to turn on the power. The
bank display indicates “P” and the 1-4 LED buttons will blink. The name display will indicate, “RELOAD? Now
release the three buttons.
2. If you’re sure you want to restore the factory data, press the WRITE button - the display will indicate
“LOADING”, and will indicate “COMPLETE” when restoring is finished. The ToneLab SE will automatically be
switched to Program Select Mode.
3. If you decide you don’t want to do this, simply press the EXIT button
SSeelleeccttiinngg aanndd lliisstteenniinngg ttoo TToonneeLLaabb’’ss 3322 PPrreesseett PPrrooggrraammss::
ToneLab has 96 program locations in 24 banks, with 4 programs in each bank (24x4=96). Programs in banks 1-8 are identical to programs in banks 9-16 and 17-24.
1. Use the BANK UP and BANK DOWN switches to select a bank.
2. Use the Channel Select switches 1-4 to select a channel in that bank.
3. Once you find a program (sound) that you like, you can use the knobs and selectors of the Pedal, Amp,
Cabinet, and Effects section to easily tweak the sound.
4. To turn ON an effect that is OFF in the program, simply press the TYPE button for the effect you wish to add.
When the LED is lit turn the knob to your effect of choice, the effect will be on. Then use the knobs below
and follow the top panel chart to edit the sound.
5. To turn OFF an effect, press the Type button.
6. Press the FX ON/OFF (TUNER) switch to go to FX ON/OFF mode. This mode lets you switch each effect
ON/OFF just like if you were using separate stomp pedals. Program switches 1-4 turn ON/OFF Pedal,
Modulation, Delay, and Reverb effects, and the BANK DOWN switch will turn ON/OFF the Insert effect. You
can plug in your own favorite pedal to the Insert Send/Return jacks on the back panel of the ToneLab SE.
The effect is on when the LED is lit.
7. By pressing the A /Bch switch you can instantly switch between the amp model and cabinet model that are
specified for A and B of each program.
8. The two Expression pedals are assigned to control the most appropriate parameters for each program, such
as wah, volume, delay, reverb input level, or other effect parameters.
9. The Control switch allows you to instantly turn on/off pedal settings, tap tempo the delay time etc. Press the
CONTROL button to make it blink, and use Value knob1 to select the effect you want to control.
CONTROL switch EFFECT ON/OFF:
“I/ON OFF” External Insert effect on/off
“P/ON OFF” Pedal effect on/off
“A/ON OFF” Amp model on/off
“C/ON OFF” Cabinet effect on/off
“M/ON OFF” Modulation effect on/off
“D/ON OFF” Delay effect on/off
“R/ON OFF” Reverb effect on/off
Note: The CONTROL button LED indicates the on/off status.
2
ToneLab EasyStart
CONTROL switch TAP TEMPO:
“MOD TAP” Use TAP TEMPO to set the speed parameter of the modulation effect.
“DLY TAP” Use TAP TEMPO to set the Time parameter of the delay effect.
FACTOR Value knob 2 setting:
If the modulation effect’s SPEED parameter or DELAY effect TIME parameter are assigned to the CONTROL
switch, you can set the MODULATION effect’s LFO SPEED or DELAY TIME by the interval at which you press the
control switch twice. When you do so, the interval at which you actually press the pedal will be applied to the
parameter at a “factor” (i.e., multiple) of 1/6, ¼, 1/3, ½, 2/3, ¾, 3/2, 2, 3, or 4, according to the setting of the
FACTOR parameter (Value knob 2).
CONTROL switch EFFECT CONTROL:
“FLN TRIG” LFO START TRIGGER of the CLASSIC FLANGER effect
“ROT SPD” SPEED switch of the ROTARY effect
“HOLD DLY” HOLD of the HOLD DELAY effect
If you’ve selected MOD TAP or DLY TAP, turn value knob2 to make the name display read “FACTOR”. Here you
can specify the proportion of the SPEED or TIME in relation to the interval of your taps. For example if you set
DLY TAP as the target, and FACTOR to “1-4”, the delay time will be set to 1/4 of the duration between taps.
To exit, press the EXIT button to return to the mode you were in.
If you decide that you don’t want to save the program with your changes, just select another program.
SSaavviinngg aa PPrrooggrraamm::
You’ve tweaked and turned some knobs, and you like the changes that you’ve made – now to save your program:
1. Press the WRITE button, and the display will blink WRITE. Use the UP/DOWN switches to choose the bank
location and the Channel 1-4 Select buttons for the Program location.
2. Press the WRITE button again and your program will be saved to its new location.
RReennaammiinngg aa PPrrooggrraamm::
1. Press the RENAME button - it will light.
2. Use the left and right (<>) buttons to move the cursor to the character you want to change (the selected
character will blink), and use VALUE knob 6 or the up and down buttons to change the character.
3. Repeat step 2 to finish inputting a name for your program.
4. When you are finished entering a name, press the WRITE button, then press the EXIT button to return to the
mode you were in.
3
Loading...