Vox AC30C2X, AC30C2, AC15C1X, AC15C2, AC15C1 Owner`s Manual [en, fr, de, es]

7SGFE

English ......................................................................................4

Français...................................................................................14

Deutsch ...................................................................................26

Español ...................................................................................36

IMPORTANT SAFETY INSTRUCTIONS

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do not use this apparatus near water.

• Mains powered apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

• Clean only with dry cloth.

• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. (for USA and Canada)

• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

• Only use attachments/accessories specified by the manufacturer.

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Turning off the power switch does not completely isolate this product from the power line so remove the plug from the socket if not using it for extended periods of time.

• Install this product near the wall socket and keep the power plug easily accessible.

• WARNING—This apparatus shall be connected to a mains socket outlet with a protective earthing connection.

• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

• Do not install this equipment on the far position from wall outlet and/or convenience receptacle.

• Do not install this equipment in a confined space such as a box for the conveyance or similar unit.

• Excessive sound pressure from earphones and headphones can cause hearing loss.

• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

The lightning flash with arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

Notice regarding disposal (EU only)

When this “crossed-out wheeled bin” symbol is displayed on the product, owner’s manual, battery, or battery package, it signifies that when you wish to dispose of this product, manual, package or battery you must do so in an approved manner. Do not discard this product, manual, package or battery along with

ordinary household waste. Disposing in the correct manner will prevent harm to human health and potential damage to the environment. Since the correct method of disposal will depend on the applicable laws and regulations in your locality, please contact your local administrative body for details. If the battery contains heavy metals in excess of the regulated amount, a chemical symbol is displayed below the “crossed-out wheeled bin” symbol on the battery or battery package.

* All product names and company names are the trademarks

or registered trademarks of their respective owners.

INTRODUCTION

Congratulations on your purchase of the VOX Guitar Amplifier Custom Series AC30C2X/AC30C2/ AC15C1X/AC15C2/AC15C1. This amp is the culmination of over 50 years of manufacturing expertise and high quality, guitar amplifier design. We have taken the best AC designs and added a number of useful features to give you the most tonally flexible AC to date! We’re confident you will find these improvements extremely useful and that your new amplifier will give you many hours of tonal pleasure. Your AC30 is equipped with a number of modern features and conveniences, a true bypass FX loop, master volume and Celestion AlNiCo Blue speakers (AC30C2X/AC15C1X only), to name a few. Please read this manual carefully so that you can familiarize yourself with them. The AC15C1X/AC15C2/AC15C1 now features both NORMAL and TOP BOOST channels, and has many common features with the AC30C2X/AC30C2. All models are fitted with the Celestion G12M Greenback as standard.

AC30C2(X) FRONT PANEL LAYOUT

12 4356

11 1312

INPUTS

1. NORMAL jack

2. TOP BOOST

jack Plugging your guitar into this input will route your signal through the TOP BOOST

NORMAL

3. VOLUME control

TOP BOOST

NOTE!

4. VOLUME control

Plugging your guitar into this input will route your signal through the NORMAL channel. Top jack for high Input, and bottom jack for low input.

channel. Top jack for high Input, and bottom jack for low input.

This determines the sensitivity of the preamp section in the NORMAL channel.

Depending on where this is set, you can either blend in more gain by turning it clockwise or you can turn it anticlockwise for a cleaner sound. The NORMAL volume can be used in conjunction with the MASTER volume which will allow you to get the perfect balance between distortion and overall volume. I.e. if you keep the NORMAL volume low and the MASTER volume high, you will get a clean sound at a high volume. Conversely, if you keep the NORMAL volume high and the MASTER volume low you will get more distortion at a lower overall volume.

The tone controls on the TOP BOOST channel are very interactive, eg increasing the level of the TREBLE control will cut the BASS level. It is best to begin with the Tone controls at 12 o’clock and experiment to find your perfect tone.

This determines the sensitivity of the preamp section in the TOP BOOST channel. Depending on where this is set, you can either blend in more gain by turning it clockwise or you can set it lower for a cleaner, “chimey” sound. The TOP BOOST Volume can be used in conjunction with the MASTER volume which will allow you to get the perfect balance between distortion and overall volume. I.e. If you keep the TOP BOOST volume low and the MASTER volume high, you will get a clean sound at a high volume. Conversely, if you keep the TOP BOOST volume high and the MASTER volume low you will get more distortion at a lower overall volume.

5. TREBLE control

6. BASS control

This controls the high frequencies in your sound—from soft and round when turned down (counterclockwise) to bright and cutting when cranked (clockwise) and all points in-between.

This controls the low frequencies in your sound—from thin and light when turned down (counterclockwise) to warm and heavy when turned up full (clockwise) and all points in-between.

REVERB

This section allows you to control the Reverb for both channels by adjusting the Tone and Level. You can remotely switch the reverb On or Off with the Optional VFS2A Foot Switch.

7. TONE control

8. LEVEL control

This controls the high and low frequencies of the REVERB. You can make the REVERB sound brighter by turning this control clockwise or you can make the sound darker by turning it counterclockwise. Experiment with this control to see which settings work best for you.

This controls the mix (amount) of REVERB in your sound. Turning this knob fully clockwise will give you a wet, saturated sound while counterclockwise will give you a drier sound.

TREMOLO

This section allows you to control the TREMOLO for both channels on this amplifier by adjusting the Speed and Depth. You can remotely switch the TREMOLO on or off with the Optional VFS2A Foot Switch.

9. SPEED control

10. DEPTH control

What is TREMOLO?

Tremolo is a Vintage Guitar Amplifier effect that hails from the Brit invasion during the 60’s. Essentially it’s like having someone sat next to your amplifier turning the master volume up and down! Having the Depth Control set to maximum will give a very dramatic effect, making your guitar sounding very choppy, you can adjust how quickly the volume is turned up and down with the speed control. Best thing to do is experiment to find your perfect sound.

As you might have guessed, this controls the SPEED of the built-in TREMOLO.

This controls the DEPTH (intensity) of the built-in TREMOLO.

MASTER

11. TONE CUT control

12. VOLUME control

POWER

13. STANDBY Switch

This circuit is placed in the power amp as opposed to the preamp section like the TREBLE and BASS controls. What this does is the opposite of what you may think. Turning it clockwise will decrease the higher frequencies and turning it counterclockwise will add higher frequencies.

This controls the overall (MASTER) VOLUME of your amplifier. Cleaner sounds can be achieved by lowering the NORMAL or TOP BOOST volumes and raising the MASTER. Setting the MASTER lower and the NORMAL and TOP BOOST volumes higher will give you a fatter, more distorted tone at a lower volume. As with all the controls of this amplifier, please experiment with different configurations to find the tones that fit your playing style.

This switch allows the amplifier to attain the correct working temperature before

applying the H.T. supply. Before connecting the amplifier to the Mains supply, ensure the Power and STANDBY switches are in the off position. Turn on the POWER switch first and then wait 2–3 minutes before turning on the STANDBY switch. Doing this each time you play helps prolong tube life. The STANDBY switch is also very useful for playing live as it allows you to keep the valves at a functional temperature between sets.

14. POWER Switch

This is the ON/OFF switch for the power to the amplifier. Please ensure the ampli-

fier is switched off and unplugged before being moved.

AC15C1X/AC15C2/AC15C1 FRONT PANEL LAYOUT

12 3 4 5

10 11

12 13

POWER

1. POWER Switch

2. STANDBY Switch

This is the ON/OFF switch for the power to the amplifier. Please ensure the ampli-

MASTER

3. VOLUME control

4. TONE CUT control

This controls the overall (MASTER) VOLUME of your amplifier. Cleaner sounds

fier is switched off and unplugged before being moved.

This switch allows the amplifier to attain the correct working temperature before

can be achieved by lowering the NORMAL or TOP BOOST volumes and raising the MASTER. Setting the MASTER lower and the NORMAL and TOP BOOST volumes higher will give you a fatter, more distorted tone at a lower volume. As with all the controls of this amplifier, please experiment with different configurations to find the tones that fit your playing style.

This circuit is placed in the power amp as opposed to the preamp section like the

TREBLE and BASS controls. What this does is the opposite of what you may think. Turning it clockwise will decrease the higher frequencies and turning it counterclockwise will add higher frequencies.

TREMOLO

This section allows you to control the TREMOLO for both channels on this amplifier by adjusting the Speed and Depth. You can remotely switch the TREMOLO on or off with the Optional VFS2A Foot Switch.

5. DEPTH control

6. SPEED control

What is TREMOLO?

This controls the DEPTH (intensity) of the built-in TREMOLO.

As you might have guessed, this controls the SPEED of the built-in TREMOLO.

REVERB

This section allows you to control the Reverb for both channels by adjusting the Level. You can remotely switch the reverb On or Off with the Optional VFS2A Foot Switch.

7. LEVEL control

TOP BOOST

NOTE!

8. BASS control

9. TREBLE control

10. VOLUME control

This controls the mix (amount) of REVERB in your sound. Turning this knob fully clockwise will give you a wet, saturated sound while counterclockwise will give you a drier sound.

This controls the low frequencies in your sound—from thin and light when turned down (counterclockwise) to warm and heavy when turned up full (clockwise) and all points in-between.

This controls the high frequencies in your sound—from soft and round when turned down (counterclockwise) to bright and cutting when cranked (clockwise) and all points in-between.

NORMAL

11. VOLUME control

INPUTS

12. TOP BOOST jack

13. NORMAL jack

This determines the sensitivity of the preamp section in the NORMAL channel. Depending on where this is set, you can either blend in more gain by turning it clockwise or you can turn it anticlockwise for a cleaner sound. The NORMAL volume can be used in conjunction with the MASTER volume which will allow you to get the perfect balance between distortion and overall volume. I.e. if you keep the NORMAL volume low and the MASTER volume high, you will get a clean sound at a high volume. Conversely, if you keep the NORMAL volume high and the MASTER volume low you will get more distortion at a lower overall volume.

Plugging your guitar into this input will route your signal through the TOP BOOST channel.

Plugging your guitar into this input will route your signal through the NORMAL channel.

REAR PANEL LAYOUT

(AC30C2(X) only)

412 3 5

1. POWER OUTPUT Jacks

This is where you can hook up an extension or external speaker cabinet(s) if desired.

NOTE!

WARNING!

a) Don’t use an extension cabinet whose impedance is other than 16 ohms. b) Don’t connect a speaker whose rated input capacity is less than 30 watts (for

c) You must use a speaker cable to connect an external speaker. Don’t use a

d) You must turn off the power before connecting the cable. Connecting the cable

NOTE!

EXTENSION SP:

are wired for 16 Ohms. The extension cabinet must be 16 Ohms.

EXTERNAL SP:

you can hook up either a 16 Ohm or 8 Ohm cabinet. Be sure to set the Output Select switch accordingly. Hooking up a cabinet through the External jack will mute (disconnect) the internal speakers! To ensure that your system works correctly, you must observe the following points.

AC30C2(X)) or 15 watts (AC15C2/AC15C1(X)). The speaker may be destroyed if you ignore this caution—not recommended!

shielded cable like the one you use to connect a guitar to an amp.

while the power is turned on may damage your amp. It is recommended that all audio cables, with the exception of the speaker lead, used to connect to the AC30C2(X)/AC15C2/AC15C1(X) of a high quality, screened type. These should not exceed 10 metres in length. Always use a non-screened Vox approved speaker lead with the AC30C2(X)/AC15C2/AC15C1(X) Amplifier and extension cabinets.

This speaker jack runs parallel with the internal speakers which

This speaker jack will mute (disconnect) the internal speakers and

2. IMPEDANCE Select switch 16 OHMS:

1) Set it to this if you use the internal speakers only.

2) Set it to this if you connect an external 16 Ohm speaker cabinet through the External jack.

8 OHMS:

1) Set it to this if you connect an extension cabinet through the Extension jack. You’ll be running the internal and external speakers in parallel. The impedance of the extension cabinet must be 16 Ohms.

2) Set it to this if you connect an external 8 ohm speaker cabinet through the External jack.

Combos allow for the following configurations:

3. EFFECTS LOOP jack

(AC30C2(X) only) The EFFECTS LOOP allows effects to be added further down the signal chain, rather than just plugging them in line with your guitar and amplifier. By using the Effects loop with Delay stomp boxes, for example, will prevent any strange distortions to the time delayed repetitions. Please note that the EFFECTS LOOP sends at -10dB meaning it is suitable for stomp boxes.

BYPASS ON/OFF:

“BYPASS” position, absolutely none of your original signal will be running through until it’s switched “ON”.

RETURN:

the output of your effect(s).

NOTE!

4. FOOT SWITCH jack

5. MAINS INPUT connector

Be sure to use shielded guitar cables only! NEVER use unshielded speaker cables.

SEND:

input of your effect(s).

This is where you connect the Optional VFS2A Foot Switch so you can turn the REVERB and TREMOLO on and off.

This is where the supplied, detachable Mains (power) cord is connected. The specific mains input voltage rating that your amplifier needs to run at is located on the rear panel of your amplifier. Before making any connections or powering up the amplifier, make sure the correct voltage is set. If you have any doubt, refer to your local VOX dealer.

This is a true bypass effects loop which means if this is set in the

Think of this as the “input” of the effects loop and will be connected to

Think of this as the “output” of the FX loop and will be connected to the

SPECIFICATION

AC30C2X

• Dimensions (W x D x H): 702 x 265 x 556 mm / 27.64 x 10.43 x 21.89 inches

• Weight: 33.4 kg / 73.59 lbs.

• Output Power: 30 Watts RMS into 16 Ohms

• Speaker: 2 x 12" 8 ohm Celestion Alnico Blue

• Inputs: Normal input jack (high and low), Top Boost input jack (high and low), FX RETURN jack, Footswitch jack

• Outputs: External loudspeaker jack, Extension loudspeaker jack, FX SEND jack

• Options: VFS2A Footswitch

AC30C2

• Dimensions (W x D x H): 702 x 265 x 556 mm / 27.64 x 10.43 x 21.89 inches

• Weight: 32.2 kg / 70.99 lbs.

• Output Power: 30 Watts RMS into 16 Ohms

• Speaker: 2 x 12" 8 ohm Celestion G12M Greenback

• Inputs: Normal input jack (high and low), Top Boost input jack (high and low), FX RETURN jack, Footswitch jack

• Outputs: External loudspeaker jack, Extension loudspeaker jack, FX SEND jack

• Options: VFS2A Footswitch

AC15C1X

• Dimensions (W x D x H): 602 x 265 x 456 mm / 23.70 x 10.43 x 17.95 inches

• Weight: 22.6 kg / 49.82 lbs.

• Output Power: 15 Watts RMS into 16 Ohms

• Speaker: 1 x 12" 16 ohm Celestion Alnico Blue

• Inputs: Normal input jack, Top Boost input jack, Footswitch jack

• Outputs: External loudspeaker jack, Extension loudspeaker jack

• Options: VFS2A Footswitch

AC15C2

• Dimensions (W x D x H): 702 x 265 x 556 mm / 27.64 x 10.43 x 21.89 inches

• Weight: 30.2 kg / 66.58 lbs.

• Output Power: 15 Watts RMS into 16 Ohms

• Speaker: 2 x 12" 8 ohm Celestion G12M Greenback

• Inputs: Normal input jack, Top Boost input jack, Footswitch jack

• Outputs: External loudspeaker jack, Extension loudspeaker jack

• Options: VFS2A Footswitch

AC15C1

• Dimensions (W x D x H): 602 x 265 x 456 mm / 23.70 x 10.43 x 17.95 inches

• Weight: 22 kg / 48.50 lbs.

• Output Power: 15 Watts RMS into 16 Ohms

• Speaker: 1 x 12" 16 ohm Celestion G12M Greenback

• Inputs: Normal input jack, Top Boost input jack, Footswitch jack

• Outputs: External loudspeaker jack, Extension loudspeaker jack

• Options: VFS2A Footswitch

*Specifications and appearance are subject to change without notice for improvement.

INFORMATIONS IMPORTANTES DE SECURITE

• Lisez attentivement ces instructions.

• Veuillez conserver ces instructions.

• Observez tous les avertissements.

• Suivez toutes les consignes à la lettre.

• N’utilisez jamais cet appareil dans un endroit humide ni à proximité d’eau.

• L’appareil alimenté par courant électrique ne peut pas être exposé à des éclaboussures; évite en outre de placer des récipients contenant des liquides, comme un vase (ou un verre de bière), sur l’appareil.

• Nettoyez uniquement l’appareil avec un chiffon doux et sec.

• Ne bloquez jamais les orifices de ventilation de l’appareil et installez-le toujours conformément aux instructions du fabricant.

• N’installez jamais l’appareil à proximité d’une source de chaleur, telle que des radiateurs, poêles ou tout autre dispositif (y compris des amplificateurs) générant de la chaleur.

• N’essayez jamais de contourner le dispositif de sécurité d’une prise de type polarisée ou d’une prise de terre. Une prise dite polarisée dispose de deux broches, dont l’une est plus large que l’autre. Une prise de terre comporte trois broches, dont une de mise à la terre. Cette broche plus large ou broche de mise à la terre vise à assurer votre sécurité. Si la fiche du cordon d’alimentation ne correspond pas au type de prise de courant de votre région, faites remplacer la prise obsolète par un électricien qualifié (pour les Etats-Unis et le Canada).

• Placez toujours le cordon d’alimentation de sorte qu’on ne risque pas de marcher dessus ni de le pincer. Cette précaution vise tout spécialement la fiche du cordon et sa sortie de l’appareil.

• Utilisez exclusivement les fixations/accessoires préconisés par le fabricant.

• S’il y a risque d’orage ou que vous ne comptez pas utiliser l’appareil pendant une période prolongée, débranchez-le du secteur.

• La mise sur OFF de l’interrupteur d’alimentation n’isole pas totalement ce produit de la ligne secteur; aussi, retirez la fiche de la prise s’il doit rester inutilisé pendant une période prolongée.

• Installez ce produit près de la prise électrique murale et gardez un accès facile à la prise électrique et au cordon d’alimentation.

• ATTENTION: Cet appareil doit absolument être connecté à une prise électrique reliée à la terre.

• Confiez tout travail de réparation uniquement à un S.A.V. qualifié. Faites appel au S.A.V. si l’appareil a subi tout endommagement, comme par exemple si sa fiche secteur ou son cordon d’alimentation sont endommagés, si de l’eau ou des objets ont pénétré à l’intérieur de l’appareil, si celui-ci a été exposé à la pluie ou à la moisissure, s’il est tombé ou présente tout signe de dysfonctionnement.

• N’utilisez jamais d’allonge trop longue avec cet appareil et ne l’alimentez jamais via les prises secteur équipant d’autres dispositifs.

• N’installez jamais cet appareil dans un endroit confiné comme une caisse de transport ou tout autre récipient similaire.

• Des niveaux d’écoute trop importants lors de l’utilisation d’un casque ou d’écouteurs peuvent entraîner des pertes d’audition.

• Utilisez l’appareil uniquement avec le chariot, stand, trépied, fixation ou table spécifiés par le fabricant ou fourni avec l’appareil. Si vous avez placé l’appareil sur un chariot, soyez très prudent quand vous déplacez le chariot, afin d’éviter une chute et des blessures.

* Tous les noms de produits et de sociétés sont des marques

L’éclair dans le triangle est un symbole destiné à attirer l’attention de l’utilisateur sur la présence de parties non isolées et de “tension dangereuse” à l’intérieur de l’appareil, qui posent des risques d’électrocution pour l’utilisateur.

Le point d’exclamation dans un triangle est un symbole destiné à attirer l’attention de l’utilisateur sur des sections de ce manuel contenant des informations importantes, liées à l’utilisation et à l’entretien de ce produit.

Note concernant les dispositions (Seulement EU)

Quand un symbole avec une poubelle barrée d’une croix apparait sur le produit, le mode d’emploi, les piles ou le pack de piles, cela signifie que ce produit, manuel ou piles doit être déposé chez un représentant compétent, et non pas dans une poubelle ou toute autre déchetterie conventionnelle.

Disposer de cette manière, de prévenir les dommages pour la santé humaine et les dommages potentiels pour l'environnement. La bonne méthode d'élimination dépendra des lois et règlements applicables dans votre localité, s’il vous plaît, contactez votre organisme administratif pour plus de détails. Si la pile contient des métaux lourds au-delà du seuil réglementé, un symbole chimique est affiché en dessous du symbole de la poubelle barrée d’une croix sur la pile ou le pack de piles.

commerciales ou déposées de leur détenteur respectif.

+ 31 hidden pages