Vizio SV370XVT Service Manual
Service Manual
Model #: SV320XVT/370XVT_LGD
AMTRAN TECHNOLOGY CO., LTD.
17F, NO. 268, Lien Chen Rd., Chung Ho City Taipei County, Taiwan, 235 R.O.C.
TEL : (02) 8228-0505 FAX : (02) 8228-0599
Confidential Document, Property of AmTRAN CO. LTD
Table of Contents
CONTENTS PAGE
Sections
1. Features 1-1
2. Specifications 2-1
3. On Screen Display 3-1
4. Factory Preset Timings
5. Pin Assignment
4-1
5-1
6. Main Board I/O Connections 6-1
7. Theory of Circuit Operation 7-1
8. Waveforms 8-1
9. Trouble Shooting 9-1
10. Block Diagram 10-1
11. Spare parts list 11-1
12. Complete Parts List 12-1
Appendix
1. Main Board Circuit Diagram
2. Main Board PCB Layout
3. Assembly Explosion Drawing
SV320/370XVT_LGD Service Manual
Service Manual
SV320/370XVT_LGD
COPYRIGHT © 2000 V, INC. ALL RIGHTS RESERVED.
IBM and IBM products are registered trademarks of International Business Machines Corporation.
Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc.
VINC and VINC products are registered trademarks of V, Inc.
VESA, EDID, DPMS and DDC are registered trademarks of Video Electronics Standards
Association (VESA).
Energy Star is a registered trademark of the US Environmental Protection Agency (EPA).
No part of this document may be copied, reproduced or transmitted by any means for any purpose
without prior written permission from VINC.
FCC INFORMATION
This equipment has been tested and found to comply with the limits of a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that the
interference will not occur in a particular installation. If this equipment does cause unacceptable
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures -- reorient or relocate the receiving antenna; increase the separation between
equipment and receiver; or connect the into an outlet on a circuit different from that to which the
receiver is connected.
FCC WARNING
To assure continued FCC compliance, the user must use a grounded power supply cord and the
provided shielded video interface cable with bonded ferrite cores. Also, any unauthorized changes
or modifications to Amtrak products will void the user’s authority to operate this device. Thus VINC
Will not be held responsible for the product and its safety.
CE CERTIFICATION
This device complies with the requirements of the EEC directive 89/336/EEC with regard to
“Electromagnetic compatibility.”
SAFETY CAUTION
Use a power cable that is properly grounded. Always use the AC cords as follows – USA (UL);
Canada (CSA); Germany (VDE); Switzerland (SEV); Britain (BASEC/BS); Japan (Electric
Appliance Control Act); or an AC cord that meets the local safety standards.
SV320/370XVT_LGD Service Manual
Chapter 1 Features
1. Built in TV channel selector for TV viewing.
2. Simulatnueous display of PC and TV images.
3. Connectable to PC’s analog RGB port.
4. Built in HDTV, S-video, composite video, HDMI, ATV and DTV, Audio line
out, Audio optical out.
5. Built in auto adjust function for automatic adjument of screen display.
6. High quality 1920X1080 pixel by pixel display.
7. Smoothing function enables display of smooth texts and graphics even if
image with resolution lower than 1920X1080 is magnified.
8. Advanced video functions for personal favor.
9. Picture In Picture (PIP) function to show TV or VCR images.
10. Power saving to reduce consumption power too less than 0.5W.
11. On Screen Display: user can define display mode
(i.e. color, brightness, contrast, sharpness, backlight),sound setting, PIP,
TV channel program, aspect and gamma or reset all setting.
CONFIDENTIAL – DO NOT COPY
Page 1-1
File No. SG-0313
Chapter 2 Specification
1. TFT-LCD CHARACTERISTICS
Model Name: SV320XVT
LC320WUD-SBT1 (Vendor: LG Display Co., Ltd)
Active Screen Size 31.55 inches(801.31mm) diagonal
Outline Dimension 731.8(H) x 426.4 (V) x 35.0 (D) Typ. [mm]
Pixel Pitch 0.36375 mm x 0.36375 mm
Pixel Format
Color Depth 10-bit, 1.06 B colors
Luminance, White 500 cd/m2 (Center 1point ,Typ.)
Viewing Angle (CR>10) Viewing angle free ( R/L 178 (Min.), U/D 178 (Min.))
Power Consumption
Weight 6,100g(Typ.)
Display Mode Transmissive mode, Normally black
Surface Treatment
1920 horiz. by 1080 vert. Pixels, RGB stripe
arrangement
Total 112.86W (Typ.) (Logic=(6.86W), Back Light=106W
(VBR-A=1.65V)
Hard coating(3H), Anti-glare treatment of the front
polarizer (Haze 10%)
CONFIDENTIAL – DO NOT COPY
Page 2-1
File No. SG-0313
Model Name: SV370XVT
LC370WUD-SBT1 (Vendor: LG Display Co., Ltd)
Active Screen Size 37 inches(940.091mm) diagonal
Outline Dimension 854.6(H) x 495.8 (V) x 35.0 mm(D) (Typ.)
Pixel Pitch 0.42675 mm x 0.42675 mm
Pixel Format 1920 horiz. by 1080 vert. Pixels, RGB stripe arrangement
Color Depth 10-bit(D), 1.06 B colors
Luminance, White 500 cd/m2 (Center 1point ,Typ.)
Viewing Angle (CR>10) Viewing angle free ( R/L 178 (Typ.), U/D 178 (Typ.))
Power Consumption
Weight 8,500g (Typ.)
Display Mode Transmissive mode, Normally black
Surface Treatment
Total 133.88W(Typ.) (Logic=8.88 W, Inverter=125W
[VBR-A=1.65V])
Hard coating(3H), Anti-glare treatment of the front polarizer
(Haze 10%)
2. Input Connectors
1x Co-axial RF (ATSC/QAM/NTSC)
3x HDMI™** with HDCP (1 with Stereo Audio RCA)
1x Component YPbPr plus Stereo Audio
1x RGB PC plus Stereo Audio
1x S-Video plus Stereo Audio (shared with AV)
1x Composite Video
Multimedia and Service port (USB).
3. Output Connectors
SPDIF Out (Optical Audio) , RCA (Audio OUT)
4. POWER SUPPLY
Input Voltage Level: 100~240 Vac, 50/ 60 Hz
Power Consumption: SV320XVT 170W MAX
SV370XVT 200W MAX
Power OFF: to less than 0.5W MAX (at 120 Vac)
CONFIDENTIAL – DO NOT COPY
Page 2-2
File No. SG-0313
5. Speaker
Built in Speakers: 6Ω/10W (max) X 2 way.
6. ENVIRONMENT
Operating Temperature: 5c~35c (Ambient)
Operating Humidity: Ta= 35 °C, 90%RH(Non-condensing)
Operating Altitude: 0 - 14,000 ft
Non-Operating : 4000 ft
7. DIMENSIONS (Physical dimension)
SV320XVT
(Unit: mm)
a. Height 568.9 512.9
b. Width 775.9 775.9
c. Depth 236.0 55.0
SV370XVT
(Unit: mm)
a. Height 630 585
b. Width 903 903
c. Depth 236 55
With Stand Without stand
With Stand Without stand
8. WEIGHT (Physical weight)
SV320XVT
a.Net: 11.5 ±1.0 kg (with base) 10.5 ±1.0 kg (without base)
b.Gross: 14.0 ±1.0 kg
SV370XVT
a.Net: 13.8 ±1.0 kg (with base) 13.0 ±1.0 kg (without base)
b.Gross: 16.8 ±1.0 kg
CONFIDENTIAL – DO NOT COPY
File No. SG-0313
Page 2-3
9. Precautions
Please pay attention to the followings when you use this TFT LCD module.
9-1. Mounting Precautions
(1) You must mount a module using holes arranged in four cornersor four
sides.
(2) You should consider the mounting structure so that uneven force (ex.
Twisted stress) is not applied to the module. And the case on which a
module is mounted should have sufficient strength so that external force is
not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in
order to protect the polarizer. Transparent protective plate should have
sufficient strength in order to the resist external force.
(4) You should adopt radiation structure to satisfy the temperature
specification.
(5) Acetic acid type and chlorine type materials for the cover case are not
desirable because the former generates corrosive gas of attacking the
polarizer at high temperature and the latter causes circuit break by
electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or
anything harder than HB pencil lead. And please do not rub with dust
clothes with chemical treatment. Do not touch the surface of polarizer for
bare hand or greasy cloth.(Some cosmetics are detrimental to the
polarizer.)
(7) When the surface becomes dusty, please wipe gently with absorbent
cotton or other soft materials like chamois soaks with petroleum benzine.
Normal-hexane is recommended for cleaning the adhesives used to attach
front / rear polarizers. Do not use acetone, toluene and alcohol because
they cause chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact
with polarizer causes deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient
strength.
CONFIDENTIAL – DO NOT COPY
Page 2-4
File No. SG-0313
9-2. Operating Precautions
(1) The spike noise causes the mis-operation of circuits. It should be lower
than following voltage:
V=±200mV(Over and under shoot voltage)
(2) Response time depends on the temperature.(In lower temperature, it
becomes longer.)
(3) Brightness depends on the temperature. (In lower temperature, it becomes
lower.) And in lower temperature, response time(required time that
brightness is stable after turned on) becomes longer.
(4) Be careful for condensation at sudden temperature change. Condensation
makes damage to polarizer or electrical contacted parts. And after fading
condensation, smearor spot will occur.
(5) When fixed patterns are displayed for a long time, remnant image is likely
to occur.
(6) Module has high frequency circuits. Sufficient suppression to the
electromagnetic interference shall be done by system manufacturers.
Grounding and shielding methods may be important to minimized the
interference.
(7) Please do not give any mechanical and/or acoustical impact to LCM.
Otherwise, LCM can’t be operated its full characteristics perfectly.
(8) A screw which is fastened up the steels should be a machine screw. (if not,
it causes metallic foreign material and deal LCM afatal blow)
(9) Please do not set LCD on its edge.
9-3. Electrostatic Discharge Control
Since a module is composed of electronic circuits, it is not strong to
electrostatic discharge. Make certain that treatment persons are connected to
ground through wrist band etc. And don’t touch interface pin directly.
9-4. Precautions for Strong Light Exposure
Strong light exposure causes degradation of polarizer and color filter.
9-5. Storage
When storing modules as spares for a long time, the following precautions are
necessary.
CONFIDENTIAL – DO NOT COPY
File No. SG-0313
Page 2-5
(1) Store them in a dark place. Do not expose the module to sunlight or
fluorescent light. Keep the temperature between 5°C and 35°C at normal
humidity.
(2) The polarizer surface should not come in contact with any other object. It is
recommended that they be stored in the container in which they were
shipped.
9-6. Handling Precautions for Protection Film
(1) The protection film is attached to the bezel with a small masking tape.
When the protection film is peeled off, static electricity is generated
between the film and polarizer. This should be peeled off slowly and
carefully by people who are electrically grounded and with well ion- blown
equipment or in such a condition, etc.
(2) When the module with protection film attached is stored for a long time,
sometimes there remains a very small amount of glue still on the bezel after
the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on thebezel
surface or its vestige is recognized, please wipe them off with absorbent
cotton waste or other soft material like chamois soaked with normal-
hexane.
CONFIDENTIAL – DO NOT COPY
Page 2-6
File No. SG-0313
Loading...