Vitamix T G 2 Blending Station Installation Manual

FOODSERVICE

Owner’s Manual

Read And Save These Instructions

Blending Station®MP

Maximum Performance

Commercial Blender

All Models

IMPORTANT SAFEGUARDS

1. Read all instructions.

2. To protect against risk of electrical shock, do not put motor base in water or other liquid.

3. Close adult supervision is necessary when appliance is used by or near children.

4. Unplug the power cord from the wall outlet when the Blending Station is not in use, before putting on or taking off parts and before cleaning other than washing the container.

5. Never contact moving parts.

6. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged in any manner .

Vita-Mix

at once for possible replacement, examination, repair, electrical or mechanical adjustment. If you live outside the United States or Canada, contact your local Vita-Mix Distributor or telephone the V International Division at +1-440-782-2450 or email international

7. The use of attachments not recommended or sold by V Corporation may cause fire, shock or injury .

Do not use outdoors.

9. Do not let the power cord hang over edge of table or counter or touch hot surfaces.

10. Keep hands and utensils out of the container while motor is running to prevent the possibility of severe personal injury and/or damage to the Blending Station MP.Arubber scraper may be used, but only when the Blending Station MPis not running.

11.

CAUTION: Blade is sharp. Handle carefully.

• Never try to remove blade while container is sitting on the motor base.

• Do not operate with loose, nicked or damaged blades.

• To reduce the risk of personal injury, never place blade assembly on

12. The maximum normal load is equivalent to the ounces (liters) listed on the container, i.e., 48 oz. (1.4 liter), and substantially less with thick mixtures.

Service, 800-4DRINK4 (800-437-4654) or 440-235-0214

vitamix.com for a distributor in your country.

motor base without blender container properly attached.

ita-Mix

Call

13. Always operate with the lid in place.

14. Display window area will scratch when contacted with a scouring pad or

sharp object. Use a soft cloth to wipe the control panel area clean.

15. The Blending Station

16. Installation for a 120 V AC unit requires you to have at least one 20 amp

outlet per machine, available within six feet of the Blending Station MP. 220 VAC and 100 VAC units require a dedicated line. Consult an electrician for proper electrical needs.

MPcannot be cleaned with a water jet.

SAVE THESE INSTRUCTIONS

Enjoy the safety of this grounded appliance. The Blending Station MP U.S. power cord comes equipped with a three-prong (grounding) plug which mates with a standard three-prong wall outlet (Figure A). This cord will vary for countries outside the United States.

Adapters (Figure B) are available for two-prong outlets. Do not cut or

remove the third (ground) prong from the plug or power cord.

Consult your electrician if you are not sure if the wall outlet is grounded through the building wiring. With a properly grounded two-prong wall outlet, ground the Blending Station MPby attaching the tab on the adapter to the wall outlet cover by means of the screw in the center of the cover (Figure B).

THREE PRONG ADAPTERS ARE NOT TO BE USED IN CANADA.

Figure A

Figure B

ERFORMANCE

AXIMUM

ontrol Panel

Display Window

High/Low Pulse

Start/Stop

Six Factory Pre-Set

Programs

Speed Control

Owner Controls

Blending Station®MP

ON/OFF switch - Located on the side of the Motor Base, the ON/OFF switch controls the power to the machine. With the machine plugged in, switch the machine to ON to ready the machine for blending. START/ST OPbutton - Pressing START/STOPonce starts and runsthe machine and turns the blades. Press the STAR T/ST OPbutton again to stop the machine and the blades. (NOTE: Pressing one of the PRE-SET PROGRAM buttons, while the motor is running, will also stop the machine.)

SPEED CONTROL button - Press the ▲ button to gradually increase the speed of the blades in increments of 1%, up to 100%. Press the ▼ button to gradually decrease the speed of the blades in increments of 1%, down to 7%. SPEED CONTROLis used to set the blending speed of the PULSE buttons (see Instructions, page 15) and the STAR T/STOPbutton (see Instructions, page 16).

NOTE: These settings will reset if the power is shut off. PRE-SET PROGRAM buttons - These buttons, numbered 1 thru 6, are

pre-programmed blending cycles designed for the most commonly made drinks. Depending on the viscosity of the drink you are creating, pressing one of the six PRE-SETPROGRAM buttons will run the machine for a full cycle. The machine will stop by itself when the cycle is complete.Acycle varies in s p e e d a n d l e n g t h ; s e e t h e Instructions on page 14 for a complete description of the range of each PRE-SETbutton. Due to the difference of recipes, your results may vary . See page 6 for information on Custom Programming these six buttons.

DISPLA YWINDOW- This area, depending on what button is pressed, displays a

variety of operation messages. A“READY” message appears when there is power to the machine.

OWNER CONTROLS-Acontrol panel accessible by pressing the Vita-Mix logo.

•Press once to reveal the mode message. Press button

READY

1then 6 within five seconds to continue. Once the correct code is entered the display will indicate the motor temperature (NORM, WARM, HOT), a usage count and a to t a l . The

MODE

“COUNT” is a machine usage total and can be reset. This can be used to keep a count of the number of drinks sold in aweek, day or even an hour. To clear, press and hold the

TEMP COUNT TOTAL

NORM 25 100

STAR T/ST OPbutton for 5 seconds. The “T OTAL” keeps track of the machine usage, including production and testing, and cannot be cleared.

VITA-MIX

SMOOTHIE

PROGRAM

• Press twice to reveal the name of the program controlling the PRE-SETbuttons. If you are using the MP settings, this will read VITA-MIXSMOOTHIE PROGRAM.

OVERWRITE

4 TO

CURRENT PROGRAM

• Press a third time to reveal an option to reset the PRE-SETbuttons to the original factory settings.

• Press a fourth time to exit and continue blending.

HIGH/LOW PULSE button - The pulse provides a quick increase or decrease in speed of the blades when blending. Press H to increase the motor to speeds that range from 51%-100%. Press L to decrease the motor speed down to a range of 50% -7%. The PULSEbutton will override the running program (as long as it is depressed). Once released the original program continues its cycle.

•The PULSE high (H) and low (L) speed is set by using the SPEED CONTROLbuttons. To set, while pressing and holding a PULSE button, press the SPEED CONTROL▲ or ▼ button until the desired motor speed is reached. The PULSEspeed will remain at this setting until changed again with the SPEED CONTROL

buttons.

ustom Programming

UNCES

ERFORMANCE

AXIMUM

The Blending Station®MPis packaged with a smoothie programming chip. Please keep the chip in a safe, easily accessible spot and always keep it in the original package. This chip is used to program your machine with the six smoothie programs optimized for the XPcontainer. Although your machine comes from the factory pre-set, follow these instructions, when using the supplied programming chip, in the event your machines PRE-SETbuttons were altered.

Programming your On-Counter Blending Station MP PRE-SET buttons

1. Turn the machine on.

2. Facing the front of the machine, insert the custom programmed chip with the words, “THIS SIDEFACING TOTHEFRONT OF THE MACHINE” toward you and the silver contact bars up, into the port located below the label area on the front of the Blending Station MP. The DISPLAYWINDOW will read “NEW MODULE.”

3. Within 10 seconds the six PRE-SETbuttons will be re-programmed and the DISPLAYWINDOW will read “SAVED” then “READY.” If nothing happens when the programming chip is fully inserted, turn the chip in the opposite direction and try again.

Custom Programmed Chip

4. Remove the programming chip and return it to the original package.

5. Press one of the six PRE-SETbuttons to reveal, in the DISPLAYWINDOW , the name of the program/drink.

Programming your In-Counter Blending Station MP PRE-SET buttons

1. Turn the machine on.

2. Remove the container from the machine. Lift the machine from the bottom edges to reveal the motor and housing area.

3. With the machine facing towards you, locate the slot underneath on the right hand side of the machine between the motor and the outer wall.

4. Insert the custom programmed chip with the

FOR

ANC

MUM

words, “THIS SIDE FACINGTO THE FRONT OF THE MACHINE” toward you and the silver contact bars up, into the slot. The DISPLAYWINDOW will read “NEW MODULE.”

5. Within 10 seconds the six PRE-SET buttons will be re-programmed and the DISPLAYWINDOW will read “SAVED” then “READY.” If nothing happens when the programming chip is fully inserted, turn the chip in the opposite direction and try again.

6. Remove the programming chip and return it to the original package.

7. Press one of the six PRE-SETbuttons to reveal, in the DISPLAYWINDOW , the name of the program/drink.

8. Carefully place the Blending Station MPmotor back into the hole in the counter.

In-Counter

Hole

Custom

Programmed

Resetting the PRE-SET buttons to the original factory settings

Chip

WARNING:Please read all step before reprogramming.Resetting the

PRE-SETPROGRAM buttons will revert the six program buttons to times that are not optimized for the XPcontainer. Use the program chip supplied with your machine and follow the instructions on page 6 for programming your machine with the correct XPprograms.

1. Enter the OWNER CONTROLS (press the Vita-Mix Logo). “MODE” will appear in the display window. Press the PRE-SETbuttons 1 and then 6. The display window will say “COUNTTEMPTOTAL.”

2. Press the Vita-Mix Logo two more times to reveal the instructions on resetting the PRE-SETbuttons.

3. Press and hold button 4 until the DISPLAYWINDOWreads “RESTORING PLEASE WAIT.” The PRE-SETbuttons are now reset to the original factory settings.

id Assembly

NOTE: Outside the United States and Canada, your Blending Station come with a different container configuration.

Two-Part Lid

48 oz. (1.4 liter) Xtreme Performance Container

The two-part lid is easy to clean and easy to put on, take off and seal.

• To remove a fully latched lid, lift the two tabs and pull upward and off.

• T wist the center lid plug to fasten or remove.

NOTE: The Xtreme Performance Container will not work on older Vita-Mix®machines. If the container does not fit on the centering pad and will not properly engage into the drive socket, the container is not compatible with your machine. Contact Vita-Mix for more information.

One-Piece Lid (optional)

48 oz. (1.4 liter) Xtreme Performance Container

The one-piece lid is easy to clean and easy to put on and take off.

• There is no lid plug for this lid.

• Add ingredients through port on top.

MPmay

Figure A

Figure B

Cover with Removable Hinge Design

Cover Door:

1. The Cover Door can be removed by opening it until the door is horizontal.

Then, gently spread the sides of the door over the round hinges and remove.

2. To reinstall the Cover Door, gently spread the sides of the door and place

the door hinge cutouts over the round hinges. (Figure C)

Tamper

Back Cover:

1. To remove the Back Cover from the Blending Station:

a. First remove the Cover Door from the unit, as described above. b. Remove the two (2) Back Cover mounting screws located on the rear of

the machine. (Figure D)

c. From the rear of the machine, firmly push the bottom of the cover forward

(towards the control panel), keeping the bottom edge of the cover against the motor base. DO NOT tilt or strike the cover during removal.

d. Slide forward until the side latches on the front of the cover are released

from the motor base. DO NOT strike the cover to “pop” the side latches

from their tracks. Doing so will cause damage. The cover must only be removed by sliding it forward (towards the Control Panel).

2. To replace the Back Cover on to the Blending Station:

a. Place the Back Cover on the motor base approximately one (1) inch

forward of its normal position.

b. Slide the cover towards the back of the machine (away from the Control

Panel). Make sure the side latches slide into their tracks.

c. Push until back of cover is seated against the Motor Base.

Make sure the Back Cover is fully seated in the back and the side latches are in their grooves before inserting and tightening the mounting screws.

d. Replace and firmly tighten the two (2) Back Cover mounting screws.

(Figure D) DO NOT overtighten. DO NOT use the mounting screws to

pull the Back Cover into position. Doing so will cause damage.

Hinge

Figure C

Cover Door

Back Cover

Mounting Screws

Figure D

+ 19 hidden pages