Vita-Mix T&G2 User Manual
FOODSERVICE
Owner’s Manual
Read And Save These Instructions
TM
T&G2
Blending Station
High Performance Commercial Blender
All Models
®
IMPORTANT SAFEGUARDS
1. Read all instructions.
2. To protect against risk of electrical shock, do not put motor base in
water or other liquid.
3. Close adult supervision is necessary when appliance is used by or
near children.
4. Unplug the power cord from the wall outlet when the T&G 2
Blending Station
and before cleaning other than washing the container.
5. Never contact moving parts.
6. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions or is dropped or damaged in any manner.
Vita-Mix
at once for possible replacement, examination, repair, electrical or
mechanical adjustment. If you live outside the United States
or Canada, contact your local Vita-Mix Distributor
Vita-Mix International Division at +1 (440) 782-2450 or email
international@vitamix.com for a distributor in your country.
7. The use of attachments not recommended or sold by V
Corporation may cause fire, shock, or injury.
8.
Do not use outdoors.
9. Do not let the power cord hang over edge of table or counter,
or touch hot surfaces.
10. Keep hands and utensils out of the container while motor is running
to prevent the possibility of severe personal injury and/or damage
to the T&G 2 Blending Station. A rubber scraper may be used, but only
when the T&G 2 Blending Station is not running.
11.
CAUTION: Blade is sharp. Handle carefully.
• Never try to remove blade while container is sitting on the motor base.
• Do not operate with loose, nicked or damaged blades.
• To reduce the risk of personal injury, never place blade assembly on
12. The maximum normal load is equivalent to the ounces (liters) listed
on the container, i.e., 32 oz. (900 ml), and substantially less with thick
mixtures.
®
motor base without blender container properly attached.
®
is not in use, before putting on or taking off parts,
Service, (800) 4DRINK4, (800-437-4654) or 440-235-0214
, or phone the
ita-Mix
Call
2
13. Always operate with the lid in place.
14. Display window area will scratch when contacted with a scouring pad or
sharp object. Use a soft cloth to wipe the control panel area clean.
15. The T&G 2 Blending Station
®
cannot be cleaned with a water jet.
16. Installation for a 120 VAC unit requires you to have at least one 20 amp
outlet per machine, available within six feet of the T&G 2 Blending
Station. 220 VAC and 100 VAC units require a dedicated line. Consult
an electrician for proper electrical needs.
SAVE THESE INSTRUCTIONS
Enjoy the safety of this grounded appliance. The T&G 2 Blending Station
U.S. power cord comes equipped with a three-prong (grounding) plug which
mates with a standard three-prong wall outlet (Figure A). This cord will vary for
countries outside the United States.
Adapters (Figure B) are available for two-prong outlets. Do not cut or
remove the third (ground) prong from the plug or power cord.
Consult your electrician if you are not sure if the wall outlet is grounded
through the building wiring. With a properly grounded two prong wall outlet,
ground the T&G 2 Blending Station by attaching the tab on the adapter to the
wall outlet cover by means of the screw in the center of the cover (Figure B).
THREE PRONG
ADAPTERS ARE
NOT TO BE USED
IN CANADA.
Figure A
Figure B
3
pecifications
S
T&G 2 Blending Station®On-Counter:
Height of unit closed: 22” (54.56 cm)
Shipping weight: 21 lbs. (9.534 kg)
Dimensions: 22” High x 9-1/4” Wide x 10-1/2” Deep
(54.56 cm x 23.45 cm x 25.86 cm)
T&G 2 Blending Station In-Counter:
Height of unit above counter: 17-1/2” (44.45 cm) closed
Depth of unit below counter: 5-2/3” (13.3 cm)
Shipping Weight: 18 lbs. (8.172 kg)
Dimensions: 24” total height x 9” Width x 12-3/4” Depth (45.03 cm x 22.65 cm x 32.39 cm)
NOTE:
For In-Counter Installation refer to pages 8-10.
Power Requirements:
Volts: 120 VAC
Amps: 11.5
Hz: 50/60
Volts: 220/240 VAC
Watts: 1073-1178
Hz: 50/60
Volts: 100 VAC (Japan)
Watts: 900
Hz: 50/60
4
ontrol Panel
C
Display Window
Six Program Buttons
T&G2 Blending Station
ON/OFF switch - Located on the side of the motor base the ON/OFF switch controls the power
to the machine. With the machine plugged in, switch the machine to ON to ready the machine
for blending.
SIX PROGRAM buttons - These buttons, numbered 1 thru 6, are pre-programmed blending cycles
designed for the most commonly made drinks. Depending on the viscosity of the drink you are
creating, pressing one of the six PROGRAM buttons will run the machine for a full cycle. The
machine will stop by itself when the cycle is complete. Or you can press one of the buttons to stop the
machine in the middle of a program cycle. Each button can be reprogrammed. See programming
instructions on page 11 for more information. A cycle varies in speed and length, see the instructions on
page 12 for a complete description of the range of each button. Due to the difference of recipes, your
results may vary.
DISPLAY WINDOW -This area depending on what button is pressed, displays a variety of
operation messages. A ‘READY’ message appears when there is power to the machine.
HIGH/LOW PULSE button - The PULSE button provides a quick increase in speed of the blades
for refreshing or finishing a drink. Press H to increase the motor speed to 100%. Press L to increase
the motor speed to 50%. The PULSE button will override the running program. Once released the
original program continues its cycle.
OWNER CONTROLS - Press the Vita-Mix logo to access the T&G 2 Blending Station control panel.
•
RECIPE 1 - 34
READY
PROGRAM ALL TO
6 TO RESTORE
Press once to reveal the option to reprogram the the SIX PROGRAM
buttons. See page 11 for instructions.
•
Press twice to exit programming and continue blending.
• Press and hold until screen changes to “
for instructions.
•
Press and hold while turning the machine on, screen changes to “6 TO
RESTORE”. Press the number six button to clear the settings of the
machines six programmed buttons and restore them to their original factory
settings. Follow the instructions on page 11 to re-program the buttons.
®
Owner Controls
High/Low Pulse
PROGRAM
ALL
T
”. See page 11
O
5
id Assembly
L
NOTE: Outside the United States and Canada, your T&G 2 Blending Station may come with a
different container configuration.
Two-part Lid
32 oz. (900 ml) Xtreme Performance Container
The two part lid is easy to clean and easy to put on, take off & seal.
• To remove a fully latched lid, lift the two tabs and pull upward
and off.
• Twist the center lid plug to fasten or remove.
Older 48 oz (1.4 liter) and 64 oz (2.0 liter) Vita-Mix containers will work on the T&G 2. The Xtreme
Performance Container (XP) will not work on older Vita-Mix Machines. Contact Vita-Mix or your
distributor for more information.
Figure A
One Piece Lid (optional)
32 oz. (900 ml) Xtreme Performance Container
The one piece lid is easy to clean and easy to put on and take off.
• There is no lid plug for this lid.
• Add ingredients through port on top.
Figure B
6
Cover with Removable Hinge Design
Cover Door:
1. The Cover Door can be removed by opening it until the door is horizontal. Then,
gently spread the sides of the door over the round hinges and remove.
2. To reinstall the Cover Door, gently spread the sides of the door and place the door
hinge cutouts over the round hinges. (Figure C)
Back Cover:
1. To remove the Back Cover from the Blending Station:
a. First remove the Cover Door from the unit, as described above.
b. Remove the two (2) Back Cover mounting screws located on the rear of the
machine. (Figure D)
c. From the rear of the machine, firmly push the bottom of the cover forward
(towards the control panel), keeping the bottom edge of the cover against the
motor base.
d. Slide forward until the side latches on the front of the cover are released from the
motor base.
tracks. Doing so will cause damage. The cover must only be removed by
sliding it forward (toward the Control Panel).
2. To replace the Back Cover on to the Blending Station:
a. Place the Back Cover on the motor base approximately one (1) inch forward of its
normal position.
b. Slide the cover towards the back of the machine (away from the Control Panel).
Make sure the side latches slide into their tracks.
c. Push until back of cover is seated against the Motor Base.
Make sure the Back Cover is fully seated in the back and the side latches
are in their grooves before inserting and tightening the mounting screws.
d. Replace and firmly tighten the two (2) Back Cover mounting screws. (Figure D)
DO NOT overtighten. DO NOT use the mounting screws to pull the Back
Cover into position. Doing so will cause damage.
DO NOT tilt or strike the cover during removal.
DO NOT strike the cover to “pop” the side latches from their
Hinge
Figure C
Cover Door
Back Cover
Back Cover
Mounting
Screws
Figure D
7
Loading...