Vision Fitness X10 Assembly Manual

Screwdriver

5mm

L-Shaped

Wrench

13/15mm Wrench

8mm

L-Shaped

Wrench

ASSEMBLY GUIDE

HARDWARE INCLUDED

X10

Elliptical Trainer

X10 ASSEMBLY GUIDE

TOOLS & PARTS INCLUDED

1600 Landmark Drive

Cottage Grove, WI 53527

toll free 800.335.4348 • fax 608.839.8731

www.visionfitness.com

2012.06.14 REV1.3

PARTS BOX

Front Stabilizer Tube (1)

Rear Stabilizer Cover (1)

Guide Rail Set (1)

Guide Rail Cover (1)

Pedal Arms (2)

Pedal Arm Covers (2 sets)

Console Mast (1)

Lower Handlebars (2)

Handlebar Caps (2)

Lower Link Arms With

Footpads (2)

Side Pedal Covers (2)

Upper Handlebars (2)

Hardware Clamshell (1)

Water Bottle Cage (1)

Top Cap (1)

Mast Boot (1)

Power Cord (1)

HARDWARE INCLUDED

X10

Elliptical Trainer

To avoid possible damage to this Elliptical Trainer, please follow assembly steps in the correct order. Before proceeding though, find your

new Elliptical Trainer’s two serial numbers located on the front axle tube, and on the back side of the console, and enter here:

Refer to this number when calling for service. Be sure to read your Owner’s Guide before using your new Elliptical Trainer.

If any parts, hardware or tools are missing, please call 1.800.335.4348

NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your Elliptical Trainer to prevent

loosening and noise. Also, during each assembly step, ensure that ALL bolts and screws are in place and partially threaded in before

completely tightening any ONE bolt or screw.

Frame Serial Number

Console Serial Number

M8x25mm Oval Hex

Socket Bolt. Qua ntity: 4

8.4x17.0x1.0t Arc Washer.

Quantity: 4

QTY:4

Z02. 8.4×17.0×1.0t Arc Washer

Z01. M8×25mm Oval Hex Socket Bolt

QTY:4

Z03. M10×25mm Round Hex Socket Bolt

Z04. 10.2×20.0×1.5t Fat Washer

Z05. 10.2×18.4×2.5t Spring Washer

QTY:2

Z06. 4×12mm Oval Cross Tapping Screw

QTY:2

Z12. 8.2×15.4×2.0t Spring Washer

Z13. M8×20mm Bolt Oval Hex Socket Bolt

Z10. 17.2×22.5×0.3t Wave Washer

Z11. 8.2×20×1.5t Fat Washer

Z09. 4×0.7×15mm Oval Cross Bolt

QTY:4

Z02. 8.4×17.0×1.0t Arc Washer

QTY:4

Z03. M10×25mm Round Hex Socket Bolt

Z04. 10.2×20.0×1.5t Fat Washer

Z05. 10.2×18.4×2.5t Spring Washer

QTY:2

Z06. 4×12mm Oval Cross Tapping Screw

QTY:2

Z12. 8.2×15.4×2.0t Spring Washer

Z13. M8×20mm Bolt Oval Hex Socket Bolt

Z10. 17.2×22.5×0.3t Wave Washer

Z11. 8.2×20×1.5t Fat Washer

Z09. 4×0.7×15mm Oval Cross Bolt

M10x25mm Rou nd Hex Socket Bolt.

Quantity: 4

10x18.4x2.5 t Spring

Washer. Quantity: 4

QTY:4

Z03. M10×25mm Round Hex Socket Bolt

Z04. 10.2×20.0×1.5t Fat Washer

Z05. 10.2×18.4×2.5t Spring Washer

QTY:2

Z06. 4×12mm Oval Cross Tapping Screw

QTY:2

Z12. 8.2×15.4×2.0t Spring Washer

Z13. M8×20mm Bolt Oval Hex Socket Bolt

Z10. 17.2×22.5×0.3t Wave Washer

Z11. 8.2×20×1.5t Fat Washer

Z09. 4×0.7×15mm Oval Cross Bolt

QTY:4

Z05. 10.2×18.4×2.5t Spring Washer

QTY:2

Z06. 4×12mm Oval Cross Tapping Screw

QTY:2

Z12. 8.2×15.4×2.0t Spring Washer

Z13. M8×20mm Bolt Oval Hex Socket Bolt

Z10. 17.2×22.5×0.3t Wave Washer

Z11. 8.2×20×1.5t Fat Washer

Z09. 4×0.7×15mm Oval Cross Bolt

QTY:4

Z04. 10.2×20.0×1.5t Fat Washer

Z05. 10.2×18.4×2.5t Spring Washer

QTY:2

Z06. 4×12mm Oval Cross Tapping Screw

QTY:2

Z12. 8.2×15.4×2.0t Spring Washer

Z13. M8×20mm Bolt Oval Hex Socket Bolt

Z10. 17.2×22.5×0.3t Wave Washer

Z11. 8.2×20×1.5t Fat Washer

Z09. 4×0.7×15mm Oval Cross Bolt

10.2x20.0x1.5t Flat

Washer. Quantity: 4

4x12mm Oval Cross

Tapping Screw. Quantity:

QTY:2

Z06. 4×12mm Oval Cross Tapping Screw

QTY:2

Z12. 8.2×15.4×2.0t Spring Washer

Z13. M8×20mm Bolt Oval Hex Socket Bolt

Z10. 17.2×22.5×0.3t Wave Washer

Z11. 8.2×20×1.5t Fat Washer

Z09. 4×0.7×15mm Oval Cross Bolt

4x10mm Oval Cross Bo lt.

Quantity: 2

QTY:2

Z12. 8.2×15.4×2.0t Spring Washer

Z13. M8×20mm Bolt Oval Hex Socket Bolt

Z10. 17.2×22.5×0.3t Wave Washer

Z11. 8.2×20×1.5t Fat Washer

Z09. 4×0.7×15mm Oval Cross Bolt

17x23x0.5t Wavy Washer.

Quantity: 2

QTY:2

Z12. 8.2×15.4×2.0t Spring Washer

Z13. M8×20mm Bolt Oval Hex Socket Bolt

Z10. 17.2×22.5×0.3t Wave Washer

Z11. 8.2×20×1.5t Fat Washer

QTY:2

Z12. 8.2×15.4×2.0t Spring Washer

Z13. M8×20mm Bolt Oval Hex Socket Bolt

Z11. 8.2×20×1.5t Fat Washer

QTY:2

Z12. 8.2×15.4×2.0t Spring Washer

Z13. M8×20mm Bolt Oval Hex Socket Bolt

QTY:2

Z13. M8×20mm Bolt Oval Hex Socket Bolt

8x20x1.5t Flat Washer.

Quantity: 2

8x15x2t Spring

Washer. Quantity:

M8x20mm Oval Hex

Socket Bolt. Qua ntity: 2

QTY:2

Z26. 8.2×20.0×1.5t Flat Washer

Z32. 20.2×27.2×1.5t Flat Washer

Z33. 20.7×29.1×0.3t Wavy Washer

QTY:4

QTY:2

QTY:4

QTY:2

Z20. M8×70mm Oval Hex Socket Bolt

Z21. 8.2×15.4×2.0t Spring Washer

Z22. 8.4×17.0×1.0t Flat Washer

Z23. M8 Nylon Nut

Z24. 15.9×28.4×1.0t Teon Washer

Z25. M8×20mm Oval Hex Socket Bolt

Z26. 8.2×20.0×1.5t Flat Washer

Z32. 20.2×27.2×1.5t Flat Washer

Z33. 20.7×29.1×0.3t Wavy Washer

M8x72mm Oval Hex Socket Bolt.

Quantity: 2

QTY:4

QTY:2

QTY:4

QTY:2

Z21. 8.2×15.4×2.0t Spring Washer

Z22. 8.4×17.0×1.0t Flat Washer

Z23. M8 Nylon Nut

Z24. 15.9×28.4×1.0t Teon Washer

Z25. M8×20mm Oval Hex Socket Bolt

Z26. 8.2×20.0×1.5t Flat Washer

Z32. 20.2×27.2×1.5t Flat Washer

Z33. 20.7×29.1×0.3t Wavy Washer

8x15x2t Spring Washer.

Quantity: 4

QTY:4

QTY:2

Z23. M8 Nylon Nut

Z24. 15.9×28.4×1.0t Teon Washer

Z25. M8×20mm Oval Hex Socket Bolt

Z26. 8.2×20.0×1.5t Flat Washer

Z32. 20.2×27.2×1.5t Flat Washer

Z33. 20.7×29.1×0.3t Wavy Washer

M8 Nylon Nut. Quantity: 2

16x28x1t Teflon Washer.

Quantity: 4

QTY:4

QTY:2

Z24. 15.9×28.4×1.0t Teon Washer

Z25. M8×20mm Oval Hex Socket Bolt

Z26. 8.2×20.0×1.5t Flat Washer

Z32. 20.2×27.2×1.5t Flat Washer

Z33. 20.7×29.1×0.3t Wavy Washer

QTY:2

Z25. M8×20mm Oval Hex Socket Bolt

Z26. 8.2×20.0×1.5t Flat Washer

Z32. 20.2×27.2×1.5t Flat Washer

Z33. 20.7×29.1×0.3t Wavy Washer

M8x20mm Oval Hex Socket Bolt.

Quantity: 2

8x20x3t Flat Washer.

Quantity: 4

QTY:2

Z32. 20.2×27.2×1.5t Flat Washer

Z33. 20.7×29.1×0.3t Wavy Washer

20x27x1.5t Flat Washer.

Quantity: 2

QTY:2

Z33. 20.7×29.1×0.3t Wavy Washer

8.5x20x1t Flat Washer. Quantity: 2

8.6x26x2t Flat Washer. Quantity:

8x15x2t Spring

Washer. Quantity:

M8x20mm Oval

Hex Socket Bolt.

Quantity: 2

20x27x1.5t Flat

Washer. Quantity:

20.7x29x0.5t Wavy

Washer. Quantity: 2

STEP 4

STEP 5

STEP 3

STEP 2

STEP 1

20.7x29x0.5t Wavy

Washer. Quantity: 2

Upper

Handlebars

Boots

Top Cap

Lower

Handlebars

Cup Holder

Console Cables

STEP 6

STEP 7

HARDWARE IS PRE-INSTALLED

Attach Console

• With the screwdriver, remove the four console mounting screws from the backside of the console. Connect the heart rate wires coming from the mast to the heart rate wires coming from the bottom of the console. Plug the data cables into the board. Pull any extra wire down into the console mast. Secure console to the bracket using the four console mounting screws removed earlier. Tighten with the screwdriver.

• Plug the power cord into the power socket in the front of the unit. Plug the other end of the cord into the wall outlet. Make sure the power switches at the bottom of the unit and on the back of the console are in the on position.

STEP 6

HARDWARE IS PRE-INSTALLED

Attach Upper Handlebars

• Slide upper handlebar onto lower handlebar and align notch with tab making sure handlebars are joined together completely. Secure upper handlebars to lower handlebars using pre-installed set screws

• Slide handlebar boots down

• Repeat on other side

Attach Top Cap

• Slide top cap over console mast and snap into place.

• Insert console mast boot over top cap and snap into place.

• Attach Cup holder using 2 preinstalled screws

COMPLETE

STEP 8

• Refer to Product Selection and Model Configuration decal on console or

follow these steps.

• Once the product is plugged in turn on the console

• Select elliptical (EP) using the resistance arrow keys. Press ENTER to select.

• Select model (X10) using the RESISTANCE arrow keys. Press ENTER to select. Console will reset to start-up screen.

• The product selection and model configuration is now complete.

STEP 1

OPEN HARDWARE FOR STEP 1

Attach Rear Stabilizer Cover

• Place rear stabilizer cover over rear stabilizer as shown

• Attach the rear stabilizer cover using 2 screws

Attach Guide Rail Set

• Align guide rail set with main frame as shown

• Attach the guide rail set to the main frame using 4 bolts, 4 spring washers and 4 flat washers

• Attach the guide rail cover to the main frame using 2 bolts

Console Mast

Bracket

Console Mast

Pedal Arm

Crank

Pedal Arm

Covers

Data Cable

Console Mast

Lower

Handlebar

Cap

Link Arm

Pedal Arm

Bracket

Lower

Handlebars

Side Pedal

Cover

Front Stabilizer Tube

Front Stabilizer

Bracket

Guide Rail Set

Main Frame Guide Rail Cover

Rear Stabilizer

Cover

Please follow the order and intent of these instructions as much as you can. The order of assembly and order of tightening the bolts will affect the performance of your new exercise machine.

Pre-Attached Bolt

and Washers

Teflon

Washers

Flat Washer

Spring Washer

Nut

Bolt

Link Arm

STEP 2

OPEN HARDWARE FOR STEP 2

Attach Levelers to Stabilizer Tube

• Screw both levelers into the holes in the bottom of the front stabilizer tube

Attach Front Stabilizer Tube

• Attach the front stabilizer tube to the front stabilizer bracket using 4 bolts and 4 arc washers

STEP 3

OPEN HARDWARE FOR STEP 3

Attach Pedal Arms

• Slide wavy washer over crank followed by pedal arm as shown. Rest pedal arm wheel on guide rail

• Attach the pedal arm to the crank using 1 flat washer, 1 spring washer and 1 bolt

• Repeat on other side

Attach Console Mast

• Tie wire to data cable and feed the connector through the console mast

• Remove 4 pre-attached bolts and washers. Attach console mast to console mast bracket with 4 preattached bolts and washers

• Make sure cable is not pinched between the console mast and console mast bracket

• Be sure to fully tighten bolts

Attach Pedal Arm Covers

• Make sure holes are on the bottom of the pedal arm

• Attach the bottom cover first with 2 pre-attached screws

• Snap on top cover

• Repeat on other side

STEP 4

OPEN HARDWARE FOR STEP 4

Attach Lower Handlebars to Console Mast

• Slide 1 large flat washer, 1 wavy washer and another large flat washer onto the console mast

• Slide lower handlebar onto console mast and attach using 1 large flat washer, 1 handlebar cap, 1 flat washer, 1 spring washer and 1 bolt

• Repeat on other side

STEP 5

OPEN HARDWARE FOR STEP 5

Attach Link Arms

• Slide wavy washer and 27mm flat washer onto link arm before sliding link arm onto pedal arm bracket

• Attach link arm to pedal arm using 1 flat washer, 1 spring washer and 1 bolt

• Align opposite end of link arm with bracket on bottom of lower handlebar

• Place Teflon washers on both sides of the link arm. While holding Teflon washers slide link arm into bottom end of lower handlebar

• Secure the joint with 1 bolt, 1 flat washer, 1 spring washer and secure with one nut

• Repeat on other side

Attach Side Pedal Covers

• Secure side pedal covers with 2 preattached screws on each side

STEP 1

STEP 2

STEP 3

STEP 4

STEP 5