Vision Fitness T9400HRT User Manual

Guide

Assembly

T9200, T9300, T9400HRT, T9500HRT,

T9600HRT, T9700HRT, & T9700S

PLATFORM TREADMILLS

platform treadmills

To avoid possible damage to this Platform Treadmill, please follow these assembly steps in the correct order. Before proceeding
though, find your new Platform Treadmill’s serial number, located on the underside of the main frame, and enter here:

Refer to this number when calling for service, and also enter this serial number on your Warranty Card and in your own records.
Be sure to read your Owner’s Guide before using your new Platform Treadmill.

If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12

NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Platform Treadmill, to prevent loos-

ening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt.

1

STEP

2

STEP

3

STEP

4

STEP

T9200

T9300

T9400HRT

T9500HRT

T9600HRT

T9700S

T9700HRT

5MMAllen Wrench

Screwdriver

TOOLS & PARTS INCLUDED

8MMAllen Wrench

PARTS BOX

Water Bottle, Qty: 1

Optional Heart Rate Chest Strap, Qty: 1

(T9400HRT, T9500HRT, T9600HRT,

T9700HRT, & T9700S only)

Color-coded Hardware Bags

Owner’s Guide

Assembly Guide

Warranty Card

HARDWARE INCLUDED

ORANGE BAG

BLUE BAG

M8 x 50L Bolts

Quantity: 4

M8 x 20L Bolts

Quantity: 2

M8 x 135L Bolts

Quantity: 4

M8 x 20L Flathead Bolts

Quantity: 4

5

1

STEP

1

STEP

• Slide the rubber covers on to the left
& right console supports, making sure
that the lower cutout is facing inward.

• Insert one of the console supports
into the console support bracket and
secure with two bolts (M8 x 20L) in
the side of the console support
bracket.

• Insert one bolt (M8 x 20L) in the
rear of the console support bracket.

• Tighten all three bolts with the blue­handled 5MMAllen wrench.

• Repeat this on the opposite side.

NOTE: The right console support has
a white wire tie attached to it.

ORANGE BAG

2

STEP

6

2

STEP

MODELS T9700HRT & T9700S: Slide
the data cables down the right
console support using the white wire
tie as a guide. Make sure that the
data cable (one large ribbon cable)
goes through the large hole in the
lower part of the console upright.

MODELS T9600HRT & T9500HRT:

Slide the data cables down the right
console support using the white wire
tie as a guide. Make sure that the
data cables (1 small & 1 large
telephone style cable) go through the
large hole in the lower part of the
console upright.

MODELS T9400HRT, T9300 &
T9200: Slide the data cables down

the right console support using the
white wire tie as a guide. Make sure
that the data cables (1 small & 1
large telephone style cable) come out
the bottom of the right console
support.

• Mount the console to the console
mast using four bolts (M8 X 20L) and
tighten with the blue-handled
5MMAllen wrench.

NOTE: Push all extra data cable into
the console mast. Make sure not to
pinch or cut the data cable.

• Mount the right-hand side mount
handlebar to the console mast using
two bolts (M8 x 135L). Repeat this on
the left-hand side.

BLUE BAG

7

3

STEP

3

STEP

MODELS T9200, T9300, T9400HRT,
T9500HRT, T9600HRT: Plug in the

small data cable into the small plug
connection on the lower control
board. Plug in the large data cable
into the large plug connection on the
lower control board.

MODELS T9700HRT & T9700S: Plug
the large 20 ribbon cable into the 20
pin connection on the lower control
board. Slide down the rubber covers
on the left & right console supports.

• Install the motor cover making sure
that the rubber covers are inserted into
the motor cover. Secure the motor
cover using the six (M5 x 10L) screws.

DATA CABLES

4

500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551

toll free 1.800.335.4348 • phone [phone] • fax [phone]

www.visionfitness.com

2001 Vision Fitness. All Rights Reserved. 11.01 Part #Z92TM49-AG18.12PRD

AG18.12PRD
REV2

4

STEP

4

STEP

• If the running belt slips when used,
use the supplied 8MMAllen wrench to
turn the left and right tension bolts
clockwise 1/4-turn at a time until the
belt no longer slips.

• If the running belt is too far to the
right side, use the supplied 8MMAllen
wrench to turn the right tension bolt

clockwise1/4-turn at a time until the

belt remains centered during use.
If the running belt is too far to the left
side, turn the left tension bolt
clockwise 1/4-turn at a time until the
belt remains centered during use.

BELT TENSION