Viofo WR1 User Manual

VIOFO

Table of Contents

Installation

Introduction

Introduction Introduction Wi-Fi Connection Operation

Operation Operation

Operation

Table of Contents

Installation

Accessories

Introduction

Interface

LED

Installation Method

Wi-Fi Connection .......................6

Download the phone app

Connect the camera through Wi-Fi

Operation

Switch ON

Switch OFF

Loop Recording

Emergency Recording

Motion Detection

PC Mode

Firmware Upgrade

.......................2

.......................6

Installation

Accessories

CarChargerAdapter

3M Adhesive Mount

Introduction

Interface

(1)

Car Charger Cable

Suction Mount

USB Cable

Clips

(2)

(3)

(4)

(6)

(1)

Power LED

(5)

Cooling Hole

(8)

Mount Slot

(2)

Wi-Fi LED

(6)

Micro-SD Card Slot

(9)

Microphone

(3)

Power Button

(7)

Power Socket

(4)

(5)

LED

Power LED

Wi-Fi LED

Activity

Solid Red

Flashing Red

Solid Blue

Flashing Blue

Status

Power ON, Recording

1. Power ON, not recording

2. Firmware upgrading

Wi-Fi connected

The camera is turned on and waiting for Wi-Fi connection

Installation Method

1) Insert the memory card

(7) (8)

(9)

Lens

It is recommended to use a Class 10, 8GB or above Micro SD card (64GB SD card is the highest supported type)

2) Install the Mount

Slide the mount into the slot on the top of camera.

Choose a suitable location for installation and make sure you have the best view possible.

3) Connect to Car Charger

Plug the cigarette adapter into your vehicles’ power port, insert the USB plug into the USB port on the camera.

Wi-Fi Connection

1) Download the phone app

If you are using the iPhone, we suggest you download the FNMultiCam app, for Android phone, we suggest download the FNNovatek app.

2) Connect the camera through Wi-Fi

Start the car to power on the camera.

Connect to the Wi-Fi connection named VIOFO-******. (The start is diﬀerent for each camera).

Start the app, for FNNovatek app, the app will automatically connect with the camera. For FNMultiCam app, while you see the “Auto connect to Device” prompt, please select “OK” to connect.

Operation

1)Switch ON

Insert the Micro SD card into the camera’s card slot. Plug the USB car adapter into the vehicle’s 12V/24V female power socket, connect the Mini USB cable’s USB port end to the USB car adapter and the Mini USB end to the camera’s female Mini USB port. Start the engine, the device will switch ON automatically.

2)Switch OFF/ON

Automatic: When the camera is ON, simply turn OFF the

engine or unplug the charging cable and the camera will switch OFF automatically.

Manual: Switching the camera OFF manually is required for vehicles where the 12V/24V female power socket provides continuous power after the engine is turned OFF.

When the camera is ON, press and hold the power button for at least 5 seconds to turn the camera OFF.

Press the power button for at least 3 seconds to turn the camera ON.

3)Loop Recording

① Insert a Micro SD card into the camera’s card slot and

automatic loop recording will begin once the camera detects power.

② Time frame for each video le is 3/5/10 minutes. ③ When there is insuﬃcient space on the Micro SD card, loop

recording will automatically overwrite the oldest les (one by one).

Loop recording les are saved to SD card:\DCIM\MOVIE folder.

4)Emergency Recording

①Automatic emergency recording

When the G-sensor is activated due to a collision, current footage will be automatically locked to avoid being overwritten by looprecording.

(Note: Collision sensing feature can be adjusted in settings on App.)

5)Motion Detection

If turned ON, the camera will start recording on detecting any movement within its FOV (eld of view). Once the camera does not detect any movement for 60 seconds, it will stop recording and go back to ‘Motion-Detection’ mode. Recording will resume if any new movement is detected.

6) PC Mode

① Connect the camera to a computer using a Mini USB cable. ② Device will automatically turn on. ③ The computer will detect “removable disk”.

There will be three folders under DCIM folder:

\MOVIE (loop recording video les) \MOVIE-RO (Emergency recording video le) \PHOTO (Video snapshot)

Copy le are needed to computer drive.

7) Firmware Upgrade

Download latest rmware, unzip the le. Copy & paste or drag & drop the .bin le to the root of the Micro SD card.

Insert the Micro SD card into the camera’s card slot once the transfer is completed.

Plug into a power source and then turn the camera ON.

LED indicator will start ashing to conrm the update’s progress.

The camera will automatically reboot after the upgrade is completed.

Currently installed rmware version can be veried by accessing the ‘Version’ tab on App.

Note:

• Before using a Micro SD card to upgrade the rmware,

formatting the card in-camera is necessary to ensure stable read and write operation.

• Do not unplug or power-oﬀ the camera during a rmware

upgrade, it may cause the camera to fail from booting.

Notice

FCC Statement

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modiﬁcations to this device not explicitly approved by manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Shenzhen Viofo Technology Co.,Ltd, declares that this RadioFrequency peripheral is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

12- month L imite d warranty

Lifeti me tech nical s uppor t

sup port@vi ofo.co m

+86 7 55 8527 8 089 (CN) Mon -Fri 9am-6 pm

VIO FO .World VIO FO_Wor ld

-1-

-2-

-3-

-4-

-5-

-6- -7- -8-

-9-

-10-