Viking PB-1, LLA-1 Technical Practice

PPrraaccttiicce

e

T

T

EELLEECCOOM

M

S

S

OOLLUUTTIIOONNSSFFOORRTTHHE

E

221

1

SST

T

C

C

EENNTTUURRY

Y

TECHNICAL

TECHNICAL

PB-1

PB-1

Panic Button

Kit

April 18, 2006

Emergency Phone Panic Button Kit

The PB-1 Panic Button Kit connects to a
Viking 1600A Series Emergency Phone to
provide a one-way talk path to the pre-pro­grammed number when used.

The PB-1 will activate the 1600A Series
Emergency Phone and allows the called
party to light a red LED to indicate that the
call is connected. The called party will be able
to hear the installation site, but the site will
not be able to hear the called party. This makes it a very effective security measure, as
there is no other indication that the site is being monitored.

PPhhoonnee......771155..338866..8888661

1

Dimensions: 65mm x 35mm x 20mm (2.56” x 1.38” x 0.79”)
Shipping Weight: 0.05kg (0.1 lbs)
Environmental: 0°C to 32°C (32°F to 90°F) with 5% to 95% non-

condensing humidity

Cord Length: 7 ft
Connections: (1) RJ11 jack

SSppeecciiffiiccaattiioonns

s

FFeeaattuurrees

s

• Courtrooms

• Bank tellers

• Gas stations

• Motel reception desks

• All night restaurants

• Convenience stores

hhttttpp::////wwwwww..vviikkiinnggeelleeccttrroonniiccss..ccoom

m

• The PB-1 is fully modular for quick plug-in
installation

• Unobtrusive - mount anywhere at any angle
with supplied foam tape

• Provides security and peace of mind

AApppplliiccaattiioonns

s

IInnssttaallllaattiioon

n

Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries assume no respon­sibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.

Fax Back Doc 233 Printed in the U.S.A.

PPrroodduuccttSSuuppppoorrttLLiinnee......771155..338866..8866666

6

FFaaxxBBaacckkLLiinnee......771155..338866..4433445

5

ZF302260 Rev A

Step 1. Mount the PB-1 using the supplied foam tape.
Step 2. Connect the RJ11 Plug on the supplied cable to

the PB-1.

Step 3. Disconnect the installed blue connector from the

1600A Series Emergency Phone board.

Step 4. Connect the green connector to the 1600A Series

Emergency Phone board.

Step 5. Connect the phone line to the RJ11 jack from the

green connector.

Note: See the 1600A Series Technical
Practice (Fax Back Document 215) for
details on setting maximum call length,
silence time out, and LED operation.

C.O. Line

The PB-1 can be mounted
up to 7ft from the 1600A
Series Emergency Phone
(with supplied cord).

Analog
PABX/KSU
Station

or

Rear View of a Standard

1600A Series Phone

RJ11

W

Waarrrraannttyy

IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT

PLEASE CONTACT: VIKING TECHNICAL SUPPORT AT [phone]

Our Technical Support Department is available for assistance Monday 8am - 4pm and Tuesday to Friday 8am - 5pm cen­tral time. So that we can give you better service, before you call please:

1. Know the model number, the serial number and what software version you have (see serial label).

2. Have your Technical Practice in front of you.

3. It is best if you are on site.

RETURNING PRODUCT FOR REPAIR

The following procedure is for equipment that needs repair:

1. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA)

number. The customer MUST have a complete description of the problem, with all pertinent information regarding the
defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc.

2. Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. St atic sen­sitive equipment such as a circuit board should be in an anti-static bag, sandwiched
between foam and individually boxed. All equipment should be wrapped to avoid packing material lodging in or stick-

ing to the equipment. Include ALLparts of the equipment. C.O.D. or freight collect shipments cannot be accepted. Ship

cartons prepaid to: Viking Electronics, 1531 Industrial Street, Hudson, WI 54016

3. Return shipping address: Be sure to include your return shipping address inside the box. We cannot ship to a P.O. Box.

4. RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.

RETURNING PRODUCT FOR EXCHANGE

The following procedure is for equipment that has failed out-of-box (within 10 days of purchase

):

1. Customer must contact Viking’s Technical Support at 715-386-8666 to determine possible causes for the problem. The

customer MUST be able to step through recommended tests for diagnosis.

2. If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input
and troubleshooting, a Return Authorization (R.A.) number will be issued. This number is valid for fourteen (14) calen­dar days from the date of issue.

3. After obtaining the R.A. number, return the approved equipment to your distributor

, referencing the R.A. number. Your
distributor will then replace the product over the counter at no charge. The distributor will then return the product to
Viking using the same R.A. number.

4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't
followed the steps listed in 1, 2 and 3, be aware that you will have to pay a restocking charge.

WARRANTY

Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of
one year from the date of purchase from any authorized Viking distributor or 18 months from the date manufactured, which ever is
greater. If at any time during the warranty period, the product is deemed defective or malfunctions, return the product to Viking
Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016. Customer must contact V iking's Technical Support Department at 715­386-8666 to obtain a Return Authorization (R.A.) number.

This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, neg­ligence or any damage caused by use of the product by the purchaser or others.

Vikings sole responsibility shall be to repair or replace (at Viking's option) the material within the terms stated above. VIKING SHALL
NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND INCLUDING INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING DIRECTLY OR INDIRECTLY FROM ANY BREACH OF ANY WARRANTY EXPRESSED OR IMPLIED, OR FOR ANY
OTHER FAILURE OF THIS PRODUCT. Some st ates do not allow the exclusion or limit ation of incidental or consequential damages,
so this limitation may not apply to you.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY EXCLUDED BEYOND THE ONE
YEAR DURATION OF THIS WARRANTY. Some states do not allow limitation on how long an implied warranty lasts, so the above
limitation may not apply to you.