Viking K-1900, K-1900-6, K-1900W-2 ASH, K-1900D-2, K-1900W-2 User Manual

...
K-1900-7
K-1900 Series
K-1900 Series
Hot Line Phones
June 27, 2002
PPhhoonnee......771155..338866..8888661
1
i
i
f
f
@
@
v
v
i
i
k
k
i
i
l
l
c
c
t
t
r
r
i
i
c
c
s
s
.
.
c
c
m
m
hhttttpp::////wwwwww..vviikkiinnggeelleeccttrroonniiccss..ccoom
m
Power: Telephone line powered (20V DC/18mA minimum) Environmental: 0°C to 32°C (32°F to 90°F) with 5% to 95%
non-condensing humidity
Dimensions: (see page 2) Dialing Speed: Normal - 120ms tones/10 pps, Fast - 50ms
tones/20 pps
Economical and Vandal Resistant
Hot-Line Phones
PPrraaccttiicce
e
T
T
EELLEECCOOM
M
S
S
OOLLUUTTIIOONNSSFFOORRTTHHE
E
221
1
SST
T
C
C
EENNTTUURRY
Y
TECHNICAL
TECHNICAL
SSppeecciiffiiccaattiioonns
s
FFeeaattuurrees
s
• Catalog sales
• Information kiosks in malls
• Courtesy and customer service phones
• Automated tellers
• Hot-line reservation phones
• Replace leased Ringdown circuits
• Security and emergency phones (pools, etc.)
• Telephone line powered
• Hearing aid compatible amplified handsets
• Rotary handset volume control
• 1 - 20 digit programmable speed dial number
• Touch Tone and 10/20 pps pulse dialing
• Non-volatile
E
2
memory (no batteries
required)
• Restricts fraudulent calls from hand held dialers
K-1900D/W-2 available in red or ash
• Optional Q170600 ringer
(Fax Back Doc 845)
• Operates on a C.O. line or analog PABX/KSU extensions
• Ring detection (will not dial on incoming calls)
• Programmable security code to enter programming mode
• Touch Tone programmable
K-1900-6 fits standard 500, 554, 2500 and 2554 set phones
AApppplliiccaattiioonns
s
The K-1900 Series of Hot-Line phones are pro­grammable to dial a 1-20 digit telephone number each time the phone’s handset is lifted. The prod-
ucts may be programmed to Touch Tone or pulse dial and will not dial on incoming calls.
The K-1900 Series phones are available in a desk or wall chassis, as well as in a
vandal resistant panel phone configuration. A network insert dialer is also available, to convert standard phones into hot-line phones.
K-1900-6
K-1900D-2
K-1900W-2 ASH
K-1900D-2 ASH
K-1900D-2
K-1900W-2
SSppeecciiffiiccaattiioonnssaannddIInnssttaallllaattiioon
n
Viking offers three variations of hot-line phones and one network dialer. Below are model numbers and descriptions of the Hot Line phones Viking offers. Each model is designed for specific applications, including varying mounting capabilities and levels of vandal protection. The following sections describe the product model numbers, their applications, installation and specifications.
Important: Use a minimum wire gauge of 26 when connecting the K-1900 phone to the public switched network.
KK--11990000DD--22HHoottLLiinneeDDeesskkPPhhoonne
e
To install the K-1900D-2 insert the RJ11 plug into a standard RJ11 jack as shown to the right.
Dimensions: 230mm x 210mm x 120mm (9.0” x 8.25” x 4.75”) Shipping Weight: 1.36 Kg (3 lbs) Connections: RJ11 Colors: Red or Ash
KK--11990000W
W--22HHoottLLiinnee
W
WaallllPPhhoonnee
To install the K-1900W-2 line up the pins of the RJ11W jack with the slots on the back of the phone, insert and press down as shown to the right.
Dimensions: 102mm x 108mm x 222mm (4.0” x 4.25” x 8.75”) Shipping Weight: 1.36 Kg (3 lbs) Connections: RJ11W Colors: Red or Ash
Optional VE-9x12 Weatherproof Housing for the K-1900W-2, available in emergency red or safety yellow. For more information on the VE- 9x12, retrieve Fax Back Document 413.
KK--11990000--66HHoottLLiinneeDDiiaalleerrNNeettwwoorrk
k
The K-1900-6 Hot-Line Dialer Network can be used with any carbon microphone handset and a double pole hook switch or typical 500, 554, 2500 and 2554 phones. Attach wires as shown to the right. An electronic ringer may be used if inbound call capability is required.
Required Handset Type: Carbon microphone Required Hookswitch: One normally open con-
tact and one normally closed contact Dimensions: 88.9mm x 68.6mm x 33mm (3.5” x
2.7” x 1.3”)
Shipping Weight: 0.45 Kg (1.0 lb) Connections: Miniature spade receptacles Compatible Phones: 500, 554, 2500 and 2554
KK--11990000--77HHoottLLiinneePPaanneellPPhhoonne
e
To install the K-1900-7 vandal resistant hot line panel phone, attach the panel to an existing dou­ble gang box (with minimum dimensions shown right) using the provided screws. Insert a cord into the RJ11 jack on the back of the K-1900-7.
Note: Four extra screws and nuts are provided to fill the unused mounting holes.
Dimensions: 127mm x 254mm x 102mm (5” x 10” x 4”)
Shipping Weight: 1.36 Kg (3 lbs) Connections: RJ-11 Panel Material: .125 inch stainless steel Mounting: Flush mount to the included double
gang box. Optional VE-5x10 weather resistant surface mount box and VE-9x20 weatherproof box for outdoor applications available.
C.O. Line
or Analog
PABX/KSU
Extension
Carbon Mic
Handset
(not
included)
Side View of the K-1900-7
Double Gang Electrical Box (not included)
Hookswitch
(shown on
hook)
RJ11
(not included)
RJ11W
(not included)
Optional VE-9x12
Fax Back Doc 413
(not included)
C.O. Line or Analog
PABX/KSU Extension
K-1900D-2
C.O. Line or Analog
PABX/KSU Extension
K-1900W-2
K-1900-6 PCB with Standard Network
Mounting Bracket (included)
#6-32 x 3/4”
Stainless Steel
Hexdrive Screws
Included
C.O. Line or
Analog PABX/KSU
Extension
Note: If the phone has a ringer, the included capacitor MUST be installed as shown above.
Optional VE-5x10
Surface Mount Box
Fax Back Doc 424
(not included)
Optional VE-9x20 Weatherproof Box Fax Back Doc 413
(not included)
-or-
!
N.O.
N.C.
Green
Red
Slate/White
Slate/Green
Slate/Red
Slate/Black
T
R
S1
S2
RX2
RX1
TX1
TX2
T E
L E P
H O N
E
0.47 mF @ 250V Capacitor (included)
White
or
Green
White
Black
Red
Optional Ringer
(not included)
3.69"
20.25"
T E L E
P H O N
E
- or -
10.14"
9.25"
5.22"
2.1"
- or -
2.75"
3.5"
A. Accessing the Programming Mode
PPrrooggrraammmmiinng
g
While in the programming mode, two beeps indicate a valid programming entry. An invalid entry will be indicated with three beeps. To exit programming, simply hang-up the K-1900 Series phone.
1. Using the Security Code
2. Without a Security Code (If You Have Forgotten or Lost the Security Code)
D. Touch Tone and Pulse Dial Speeds
The K-1900 Series phone can be programmed to dial at normal or fast dialing speeds. While in the programming mode, enter 1 for normal dialing speed - 120ms on/off Touch Tones or 10 pps pulse dialing. Enter 2 for fast dialing speed - 50ms on/off Touch Tones or 20 pps pulse dialing.
C. Programming Examples
JP1
Remove to enter program­ming without a security code.
Note: JP1 MUST be in place for normal operation.
Step 1. Connect the K-1900 Series device to an analog C.O. line, or an analog PABX/KSU station.
Step 2. From a Touch Tone phone, call into the K-1900 Series phone.
Step 3. Listen for at least one ringback in the calling phone and then take the K-1900 Series phone off-hook (answer the
phone).
Step 4. From the Touch Tone phone, enter your six digit security code (factory set to 845464 - see section E).
Step 5. A double beep indicates the K-1900 Series phone is in the programming mode (see sections B-G ). If six digits are
entered and no beeps are heard, an incorrect security code has been entered. Repeat steps 2-5 or follow directions in 2. Without a Security Code below.
Step 1. Remove JP1 (as shown to the right). For the K-1900W-2 and K-1900D-2, the
plastic cover must be removed to expose the circuit board.
Step 2. Connect the K-1900 Series device to a C.O. line, analog PABX/KSU station or
to a DLE-200B Line Simulator.
Step 3. From a Touch Tone phone, call into the K-1900 Series phone.
Step 4. Listen for at least one ringback in the calling phone and then take the K-1900
Series phone off-hook (answer the phone).
Step 5. A double beep indicates the K-1900 Series phone is in the programming mode
(see Programming sections B-G).
Step 6. When programming is finished, replace JP1 and replace cover on phone.
B. Quick Programming Guide
Enter Digits
then
Memory
Location
Speed dial number (see section C) 1-20 digits or pauses .............................................
Security Code, factory set to 845464 (see section E) ...................................................
To add a anywhere in the dialing string .....................................................................
To add a # anywhere in the dialing string ......................................................................
To set dialing speed to normal - 120ms tones/10 pps (factory setting) ..........................
To set dialing speed to fast - 50ms tones/20pps ...........................................................
To restrict Touch Tone user dialing (factory setting) ......................................................
To enable Touch Tone user dialing ................................................................................
Toggles between pulse and Touch Tone dialing (see section C) ...................................
To add a 4 second pause anywhere in the dialing string (see section C) ......................
To add a 1 second pause anywhere in the dialing string ...............................................
#0 #9
phone number 6 digits
✱✱ ✱#1234678
then then
To Program the ACD-10 to...
...to Touch Tone dial 555-1234
...to pulse dial 555-1234 followed by a Touch Tone 9
...to dial a 9, a 4 second pause and then 555-1234
...to set the dialing speed to fast
...to enable unlimited user dialing after the phone has speed dialed
...to clear the speed dial number or disable speed dialing
Step 2 - Enter Digits
5551234 + #0
6 5551234 6 9 + #0
9 7 5551234 + #0
2
4
#0
Step 1 - See section A
Enter Programming
Enter Programming
Enter Programming
Enter Programming
Enter Programming
Enter Programming
Install Your Viking Product in a Weatherproof Enclosure
The VE-9x12 and VE-9x20 provide the ultimate in weather protection for your Viking product!
The enclosures are constructed of cast aluminum and is made for years of outdoor service. The heavy-duty alu­minum door is labeled “Telephone” and has a gasket seal to keep out even the harshest weather. The VE- 9x12 and VE-9x20 are available in two high visibility col­ors: safety yellow or emergency red.
For more information on the VE-9x12 or VE-9x20, retrieve Fax Back Document 413.
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
Fax Back Doc 360
ZF300950 Rev G
Printed in the U.S.A.
The K-1900 Series phones is factory set to restrict fraudulent calls from hand held pocket dialers. After speed dialing, the K-1900 Series phones will restrict (hang up) when they detect any Touch Tone that they did not generate. To restrict user dialing, enter
3 while in the programming mode. To enable user dialing, enter 4 while in the programming mode.
G. Touch Tone User Dialing Restriction (factory enabled)
An optional Q170600 internal ringer is available. For more informa­tion, retrieve Fax Back Document 834.
.47 mF @ 250V
(included with ringer)
Q170600
Electronic Ringer
AAddddiinnggaannIInntteerrnnaallRRiinnggeer
r
RReellaatteeddPPrroodduucctts
s
Vandal Resistant Hot-Line Panel Phone with Touch Tone Keypad
The K-1900-8 Stainless Steel Panel Phone features a built-in Hot-Line dialer as well as a weather resist­ant keypad. The dialer can provide both Touch Tone dialing as well as 10/20 pps pulse dialing. After the phone number has been dialed, the Touch Tone keypad is enabled to permit additional manual dialing.
The K-1900-8 housing consists of a heavy gauge, stainless steel panel, a metal Touch Tone keypad, an armored cable, and an all metal cradle for both weather and vandal resistance.
For more information on the K-1900-8 Hot-Line Panel Phone, retrieve Fax Back Document 312. For more information on the VE-Series Surface Mount Boxes, retrieve Fax Back Document 424.
Weatherproof
Enclosures
PPrroodduuccttSSuuppppoorrttLLiinnee......771155..338866..8866666
6
FFaaxxBBaacckkLLiinnee......771155..338866..4433445
5
K-1900-8
Shown with VE-5x10
F. Touch Tone or Pulse Dialing
The K-1900 Series phones are factory set to automatically dial using Touch Tones. A 6 entered in the speed dial num­ber will toggle the dialing mode between Touch Tone and pulse (see section C).
Note: You can NOT program a
and # to be pulse dialed.
E. Security Code
A six digit security code is required to access the programming mode. The factory set security code is 845464 (V-I-K- I-N-G). It is recommended that you change the security code to a personal 6 digit (0-9) number in memory position #9 while in the programming mode. Note: The security code must be six digits in length and cannot contain a
or #.
T
R
Loading...