
Copyright
Copyright © 2006 by ViewSonic Corporation. All rights reserved. No part of this publication may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer
language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission of ViewSonic Corporation.
Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied, with respect to the contents
hereof and specifically disclaims any warranty of merchantability or fitness for any particular purpose. Further,
ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents
hereof without obligation of ViewSonic to notify any person of such revision or changes.
Trademarks
Optiquest is a registered trademark of ViewSonic Corporation.
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.
Revision History
Revision SM Editing Date ECR Number
Description of Changes Editor
1a 12/26/2005 Initial Release Jamie Chang
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
1b 04/20/2005 Change Prefix # of VA902-2 (replace P4Q with Q4Q) J. Chang

View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
TABLE OF CONTENTS
1. Precautions and Safety Notices 1
2. Specification 4
3. Front Panel Function Control Description 7
4. Circuit Description 14
5. Adjustment Procedure 21
6. Troubleshooting Flow Chart 40
7. Recommended Spare Parts List 43
8. Exploded Diagram and Exploded Parts List 53
9. Block Diagrams 56
10. Schematic Diagrams 57
11. PCB Layout Diagrams 65

1. Precautions and Safety Notices
1. Appropriate Operation
(1) Turn off the product before cleaning.
(2) Use only a dry soft cloth when cleaning the LCD panel surface.
(3) Use a soft cloth soaked with mild detergent to clean the display housing.
(4) Disconnect the power plug from AC outlet if the product is not used for a long period of
time.
(5) If smoke, abnormal noise, or strange odor is present, immediately switch the LCD display
off.
(6) Do not touch the LCD panel surface with sharp or hard objects.
(7) Do not place heavy objects on the LCD display, video cable, or power cord.
(8) Do not use abrasive cleaners, waxes or solvents for your cleaning.
(9) Do not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- Place in direct sunlight.
2. Caution
No modification of any circuit should be attempted. Service work should only be performed after
you are thoroughly familiar
with all of the following safety checks and servicing guidelines.
3. Safety Check
Care should be taken while servicing this LCD display. Because of the high voltage used in the
inverter circuit, the voltage is exposed in such areas as the associated transformer circuits.
4. Power Supply Requirements
The external AC power operating range shall be from 90 to 264Vac
5. LCD Module Handling Precautions
5.1. Handling Precautions
(1) Since front polarizer is easily damaged, pay attention not to scratch it.
(2) Be sure to turn off power supply when inserting or disconnecting from input connector.
(3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
(4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
(5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
(6) Since CMOS LSI is used in this module, take care of static electricity and insure human
earth when handling.
(7) Do not open nor modify the Module Assembly.
(8) Do not press the reflector sheet at the back of the module to any directions.
(9) In case if a Module has to be put back into the packing container slot after once it was
taken out from the container, do not press the center of the CCFL Reflector edge.
Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT
Module may be damaged.
(10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
tilt the Interface Connector of the TFT Module.
(11) After installation of the TFT Module into an enclosure (LCD monitor housing, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.
(12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please
follow local ordinances or regulations for disposal.
(13) Small amount of materials having no flammability grade is used in the LCD module.
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
1

The LCD module should be supplied by power complied with requirements of Limited
Power Source (IEC60950 or UL1950), or be applied exemption.
(14) The LCD module is designed so that the CFL in it is supplied by Limited Current
Circuit (IEC60950 or UL1950). Do not connect the CFL in Hazardous Voltage Circuit.
5.2. Handling and Placing Methods
Correct Methods: Incorrect Methods:
Only touch the metal frame of the LCD panel
or the front cover of the monitor. Do not touch
the surface of the polarizer.
Surface of the LCD panel is pressed by fingers
and that may cause “Mura”
Take out the monitor with cushions Taking out the monitor by grasping the LCD
panel. That may cause “Mura”
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
2

2. Specification
1. General Requirements
General Specifications
Test Resolution & Frequency “1280 x 1024” @ 60Hz
Test Image Size Full Size
Contrast and Brightness Controls Factory Default:
Contrast = 70%, Brightness = 100%
2. Signal Interface
Video Interface
Analog Input Connector DB-15 (Analog)
Default Input Connector Defaults to the first detected input
Video Cable Connector DB-15 Pin out Compliant DDC 1/2B.
Video Signals 1. Video RGB (Analog) Separate Sync
Video Impedance 75 Ohms (Analog), 100 Ohms (Digital)
Exclusions Not compatible with interlaced video.
3. Power
Power Supply
Input Voltage Range 90 to 264 VAC
Power Dissipation 40 Watts (Typ.)
4. Electrical Requirements
Horizontal / Vertical Frequency
Horizontal Frequency 30 – 82 KHz
Vertical Refresh Rate 50 – 85 Hz
* For resolution 1280 x 1024, the vertical
Refresh rate up to 75 Hz; for there rest
Resolutions, the vertical refresh rate up
To 85Hz
Maximum Pixel Clock 135 MHz
Sync Polarity Independent of sync polarity.
Timing Table
Item Timing Analog
1 640 x 350 @ 70Hz, 31.5kHz Yes
2 640 x 400 @ 60Hz, 31.5kHz Yes
3 640 x 400 @ 70Hz, 31.5kHz Yes
4 640 x 480 @ 50Hz, 24.7kHz Yes
5 640 x 480 @ 60Hz, 31.5kHz Yes
6 640 x 480 @ 67Hz, 35.0kHz Yes
7 640 x 480 @ 72Hz, 37.9kHz Yes
8 640 x 480 @ 75Hz, 37.5kHz Yes
9 640 x 480 @ 85Hz, 43.27kHz Yes
10 720 x 400 @ 70Hz, 31.5kHz Yes
11 800 x 600 @ 56Hz, 35.1kHz Yes
12 800 x 600 @ 60Hz, 37.9kHz Yes
13 800 x 600 @ 75Hz, 46.9kHz Yes
14 800 x 600 @ 72Hz, 48.1kHz Yes
15 800 x 600 @ 85Hz, 53.7kHz Yes
16 832 x 624 @ 75Hz, 49.7kHz Yes
17 1024 x 768 @ 60Hz, 48.4kHz Yes
18 1024 x 768 @ 70Hz, 56.5kHz Yes
19 1024 x 768 @ 72Hz, 58.1kHz No
20 1024 x 768 @ 75Hz, 60.0kHz Yes
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
4

21 1024 x 768 @ 85Hz, 68.67kHz Yes
22 1152 x 864 @ 75Hz, 67.5kHz No
23 1152 x 870 @ 75Hz, 68.7kHz Yes
24 1280 x 1024 @ 60Hz, 63.4kHz Yes
25 1280 x 1024 @ 75Hz, 79.97kHz Yes
26 1280x 720 @ 60Hz, 45kHz (HDTV) Yes
Changing Modes
Maximum Mode Change Blank Time for image
stability. Note:
1) Excluding “Auto Adjust” time
2) Under DOS mode (640 x 350, 720 x 400 & 640 x
400), there is no “Auto Adjust” feature.
3) The monitor needs to do “Auto Adjust” the first
time a new mode is detected.
Under 3 seconds (Maximum)
1 seconds (Typ.) for recognized timings
1-2 seconds (Typ.) for unrecognized timing
5. LCD Panel
Panel Characteristics
Panel Type M190EN03V3
Type VA type with LVDS interface
Active Size 376.32 (H) x 301.056 (V)
Pixel Arrangement RGB Vertical Stripe
Pixel Pitch 0.294 mm
# of Backlights 4 CCFL edge-light (2 top / 2 bottom)
Backlight Life 40,000 Hours (minimum)
Panel Performance
Luminance –
Condition:
CT = 6500K, Contrast = Max,
Brightness = Max
250 cd/m
2 (typ. after 30-minute warm-up)
200 cd/m2 (minimum after 30-minute warm-up)
Brightness Uniformity 80% (typ)
75% (min)
Contrast Ratio 1000:1 (typ.), 750:1 (minimum)
Color Depth 16.7M colors (RGB 8-bit data)
Viewing Angle (Horizontal) 170 degrees @ CR>10
Viewing Angle (Vertical) 170 degrees @ CR>10
Response Time
10%-90% @ Ta=25°C
14 ms (Tr= 9 ms, Tf = 5 ms) (typ.)
40 ms (Tr= 25 ms, Tf =15 ms) (maximum)
6. Mechanical
Dimensions
Width 414 mm
Height 407 mm
Depth 219 mm
Monitor Weight 5.4kg / 11.88 lbs
Ergonomics
Tilt Up 20 DEGREES MINIMUM
Tilt Down -5 degrees
Package Specifications
Width 490 mm
Height 570 mm
Depth 145 mm
Gross Weight 6.8kg (14.96lb)
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
5

Front Control Panel
shown below in detail
Main Menu
With OnView controls
Scrolls through menu options and
adjusts the displayed control.
Also a shortcut to display the
Contrast adjustment control
screen.
Power
On/Off
Displays the control
screen for the highlighted
control.
Also toggles between two
controls on some
screens.
Also a shortcut to Auto
Image Adjust.
Power light
Green = ON
Orange = Power Saving
Displays the Main Menu
or exits the control screen
and saves adjustments.
3. Front Panel Function Control Description
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
7

. (The black border around the
edge of the screen should barely touch the illuminated “active area” of the
LCD dislay.)
The line at the
bottom of the
screen tells you
what you can do
next: Exit or Select
the control that is
highlighted.
Main Menu
1:EXIT 2:SELECT
Auto Adjust
Contrast/Brightness
Color Adjust
Information
Image Adjust
Setup Menu
Memory Recall
AUTO
SET
i
?
Do the following to adjust the screen image:
1
To display the Main Menu, press button [1].
4
To adjust the control, press the upIor downJbuttons.
5
To save the adjustments and exit the menu, press button [1] twice.
The following tips may help you optimize your display:
• Adjust your computer's graphic card so that it outputs a video signal 1280 x
1024 @ 60 Hz to the LCD dislay. (Look for instructions on “changing the
refresh rate” in your graphic card's user guide.)
• If necessary, make small adjustments using H. POSITION and V. POSITION
until the screen image is completely visible
NOTE: All OnView menus and adjustment screens disappear automatically
after about 15 seconds. This time period is adjustable through the Setup
menu and the OSD timeout control described on page 11.
2
To highlight a control you want to adjust, press I or J to scroll up or down
the Main Menu.
3
To select the highlighted control, press button [2]. A control screen appears
like the example shown below.
Contrast
1:EXIT 2: Brightness
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
8

Main Menu Controls
Adjust the menu items shown below by using the up Iand down Jbuttons.
Control Explanation
Auto Adjust
automatically sizes, centers, and fine tunes the
video signal to eliminate waviness and distortion.
Press the [2] button to obtain a sharper image.
NOTE
: Auto Adjust works with most common video cards. If
this function does not work on your LCD dislay, then lower the
video refresh rate to 60 Hz and set the resolution to its pre-set
value.
Contrast
adjusts the difference between the image background
(black level) and the foreground (white level).
Brightness
adjusts background black level of the screen image.
Color Adjust
provides several color options: preset color
temperatures and User which allows you to adjust red (R), green
(G), and blue (B). The factory setting for this product is 6500K
(6500 Kelvin).
6500K
— Adds red to the screen image for warmer white and
richer red. Default setting.
9300K
— Adds blue to the screen image for cooler white (used
in most office settings with fluorescent lighting).
sRGB
— sRGB is quickly becoming the industry standard for color
management, with support being included in many of the latest
applications. Enabling this setting allows the LCD display to
more accurately display colors the way they were originally
intended. Enabling the sRGB setting will cause the Contrast and
Brightness adjustments to be disabled.
5400K — Adds green to the screen image for a darker color.
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
9

Information
displays the timing mode (video signal input)
coming from the graphics card in your computer. See your
graphic card’s user guide for instructions on changing the
resolution and refresh rate (vertical frequency).
VESA 1280 x 1024 @ 60 Hz (recommended) means that the
resolution is 1280 x 1024 and the refresh rate is 60 Hertz.
Control Explanation
i
H. Size
(Horizontal Size) adjusts the width of the screen image.
NOTE:
Vertical size is automatic with your LCD dislay.
H./V. Position
adjusts horizontal and vertical position of the
screen image. You can toggle between Horizontal and Vertical
by pressing button [2]. Horizontal moves the screen image to
the left or to the right. Vertical moves the screen image up and
down.
Image Adjust
The Image Adjust controls are explained below:
Image Adjust
1:EXIT 2:SELECT
H./V. Position
H. Size
Fine Tune
Sharpness
1
To select color (R, G or B) press button [2].
2
To adjust selected color, press I or J.
3
When you are finished making all color adjustments, press
button [1] twice.
User
— Individual adjustments for red, green, and blue.
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
10

Fine Tune sharpens focus by aligning the illuminated text and/
or graphic characters.
NOTE: Try the Auto Adjust (see page 9) before using the Fine
Tune control.
Sharpness
adjusts the clarity and focus of the screen image.
Setup Menu displays the menu shown below.
Explanation
the menus and control screens.
The Setup Menu controls are explained below.
OSD Position
allows you to move the on-screen display menus
and control screens.
OSD Timeout
sets the length of time an on-screen display
screen is displayed. For example, with a “15 second” setting, if
a control is not pushed within 15 seconds, the display screen
disappears.
Resolution Notice
advises the optimal resolution to use.
Language
Select allows you to choose the language used in
OSD
?
Control
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
11

Short Cut Key
Function Key : 5 Keys !!!! 1 2 ▼
▼▼▼
▲▲▲▲
[1] Main Menu
[2] Auto Image Adjust
[▼▼▼▼] or [▲▲▲▲]
to immediately activate Contrast menu.
It should be change to Brightness OSD
by push button [2].
[▼▼▼▼] + [▲▲▲▲]
recall Contrast or Brightness while in
the Contrast or Brightness adjustment,
or recall both of Contrast and
Brightness when the OSD is not open.
[1] + [2] toggle 720x400 and 640x400 mode when
input 720x400 or 640x400 mode.
[1] + [▼▼▼▼] + [▲▲▲▲]
(Keep pushing 5 sec)
White Balance.
[1] + [▼▼▼▼]
Power Lock
[1] + [▲▲▲▲]
OSD Lock
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
13

4. Circuit Description
A. Scaling controller
GENERAL DESCRIPTION
The TSU16AS is total solution graphics processing IC for LCD monitors with panel
resolutions up to SXGA. It is configured with a high-speed integrated triple-ADC/PLL, a high
quality display processing engine, and an integrated output display interface that can support
LVDS panel interface format. To further reduce system costs, the TSU16AS also integrates
intelligent power management control capability for green-mode requirements and
spread-spectrum support for EMI management.
The TSU16AS incorporates the world’s first coherent oversampled RGB graphics ADC in a
monitor controller system1. The oversampling ADC samples the input RGB signals at a
frequency that is much higher than the signal source pixel rate. This can preserve details in the
video signal that ordinarily would be lost due to input signal jitter or bandwidth limitations in
non-oversampled systems.
The TSU16AS also incorporates a new Dynamic Frame Rate (DFR) generator2 for the digital
output video to the display panel that preserves the advantages of a fixed output clock rate,
while eliminating the output end of frame short-line.
1,2 Patent Pending
PIN DESCRIPTION
CPU Interface
Pin Name Pin Type Function Pin
HWRESET Schmitt Trigger Input w/
5V-tolerant
Hardware reset; active high 5
INT Output CPU interrupt; 4mA driving strength 27
AD3 I/O w/ 5V-tolerant DDR direct bus AD3; 4mA driving strength 4
AD2 I/O w/ 5V-tolerant DDR direct bus AD2; 4mA driving strength 1
AD1 I/O w/ 5V-tolerant DDR direct bus AD1; 4mA driving strength 2
AD0 I/O w/ 5V-tolerant DDR direct bus AD0; 4mA driving strength 3
ALE I w/ 5V-tolerant DDR direct bus ALE; active high 24
WRZ I w/ 5V-tolerant DDR direct bus WRZ; active low 25
RDZ I w/ 5V-tolerant DDR direct bus RDZ; active low 26
Analog Interface
Pin Name Pin Type Function Pin
HSYNC Schmitt Trigger Input w/
5V-tolerant
Analog HSYNC input 8
VSYNC Schmitt Trigger Input w/
5V-tolerant
Analog VSYNC input 9
REFP Internal ADC top de-coupling pin 22
REFM Internal ADC bottom de-coupling pin 23
RINP Analog Input Analog red input 19
RINM Analog Input Reference ground for analog red input 18
SOGIN Analog Input Sync-on-green input 17
GINP Analog Input Analog green input 16
GINM Analog Input Reference ground for analog green input 15
BINP Analog Input Analog blue input 14
BINM Analog Input Reference ground for analog blue input 13
REXT External resistor 390 ohm to AVDD_ADC 11
LVDS Interface
Pin Name Pin Type Function Pin
LVA0M Output A-Link Negative LVDS Differential Data Output 42
LVA0P Output A-Link Positive LVDS Differential Data Output 41
LVA1M Output A-Link Negative LVDS Differential Data Output 40
TSU16AS
SXGA LCD Controller with Analog Interface and Dual LVDS Transmitter
Preliminary Data Sheet Version 0.2
Version 0.2 - 5 - 10/1/2004
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
14

Copyright c 2004 MStar Semiconductor, Inc. All rights reserved.
Pin Name Pin Type Function Pin
LVA1P Output A-Link Positive LVDS Differential Data Output 39
LVA2M Output A-Link Negative LVDS Differential Data Output 38
LVA2P Output A-Link Positive LVDS Differential Data Output 37
LVA3M Output A-Link Negative LVDS Differential Data Output 34
LVA3P Output A-Link Positive LVDS Differential Data Output 33
LVACKM Output A-Link Negative LVDS Differential Clock Output 36
LVACKP Output A-Link Positive LVDS Differential Clock Output 35
LVB0M Output B-Link Negative LVDS Differential Data Output 52
LVB0P Output B-Link Positive LVDS Differential Data Output 51
LVB1M Output B-Link Negative LVDS Differential Data Output 50
LVB1P Output B-Link Positive LVDS Differential Data Output 49
LVB2M Output B-Link Negative LVDS Differential Data Output 48
LVB2P Output B-Link Positive LVDS Differential Data Output 47
LVB3M Output B-Link Negative LVDS Differential Data Output 44
LVB3P Output B-Link Positive LVDS Differential Data Output 43
LVBCKM Output B-Link Negative LVDS Differential Clock Output 46
LVBCKP Output B-Link Positive LVDS Differential Clock Output 45
GPO Interface
Pin Name Pin Type Function Pin
PWM1 Output PWM1; 4mA driving strength 29
PWM0 Output PWM0; 4mA driving strength 28
Misc. Interface
Pin Name Pin Type Function Pin
XIN Crystal Oscillator Input Xin 6
XOUT Crystal Oscillator Output Xout 7
VCTRL Output Regulator Control 54
Power Pins
Pin Name Pin Type Function Pin
AVDD_ADC 3.3V Power ADC Power 12, 20
VDDP 3.3V Power Digital Output Power 30, 53
DDC 1.8V Power Digital Core Power 32, 55
GND Ground Ground 10, 21, 31, 56
ELECTRICAL SPECIFICATIONS
Analog Interface Characteristics
Parameter Min Typ Max Unit
Resolution 8 Bits
DC ACCURACY
Differential Nonlinearity ±0.5 +1.50/-1.0 LSB
Integral Nonlinearity ±1 LSB
No Missing Codes Guaranteed
ANALOG INPUT
Input Voltage Range
Minimum 0.5 V p-p
Maximum 1.0 V p-p
Input Bias Current 1 uA
Input Full-Scale Matching 1.5 %FS
Brightness Level Adjustment 62 %FS
SWITCHING PERFORMANCE
Maximum Conversion Rate 220 MSPS
Minimum Conversion Rate 12 MSPS
HSYNC Input Frequency 15 200 kHz
PLL Clock Rate 12 220 MHz
PLL Jitter 500 ps p-p
Sampling Phase Tempco TBD ps/ C〣
DIGITAL INPUTS
Input Voltage, High (VIH) 2.5 V
Input Voltage, Low (VIL) 0.8 V
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
15

Input Current, High (IIH) -1.0 uA
Input Current, Low (IIL) 1.0 uA
Input Capacitance 5 pF
DIGITAL OUTPUTS
Output Voltage, High (VOH) VDDP-0.1 V
Output Voltage, Low (VOL) 0.1 V
DYNAMIC PERFORMANCE
Analog Bandwidth, Full Power 250 MHz
Channel to Channel Matching 0.5% Full-Scale
Specifications are subjected to change without notice.
TSU16AS
SXGA LCD Controller with Analog Interface and Dual LVDS Transmitter
Preliminary Data Sheet Version 0.2
Version 0.2 - 7 - 10/1/2004
Copyright c 2004 MStar Semiconductor, Inc. All rights reserved.
Absolute Maximum Ratings
Parameter Symbol Min Typ Max Units
3.3V Supply Voltages VVDD_33 -0.3 3.6 V
1.8V Supply Voltages VVDD_18 -0.3 1.98 V
Input Voltage (5V tolerant inputs) VIN5Vtol -0.3 5.0 V
Input Voltage (non 5V tolerant inputs) VIN -0.3 VVDD_33 V
Ambient Operating Temperature TA 0 70 °C
Storage Temperature TSTG -40 150 °C
Junction Temperature TJ 150 °C
Thermal Resistance (Junction to Air) Natural
Conversion
θJA TBD °C /W
Thermal Resistance (Junction to Case) Natural
Conversion
θJC TBD °C /W
Note: Stress above those listed under Absolute Maximum Rating may cause permanent
damage to those indicated in the stress rating only; functional operation of the device at
these or any other conditions outside of those indicated in the operation sections of this
specification is not implied. Exposure to absolute maximum ratings foextended periods
may affect device reliability.
ORDERING GUIDE
Model Temperature
Range
Package
Description
Package
Option
TSU16AS 0°C to +70°C SDIP
MTV512M64
The MTV512M micro-controller is an 8051 CPU core embedded device especially tailored for
flat panel display applications. It includes an 8051 CPU core,768-byte SRAM, 4 channels of
6-bit ADC, 3 external counters/timers, 6 channels of PWMDAC, VESA DDC interface, and a
64K-byte internal program Flash-ROM memory.
FEATURES
• 8051 core, CPU operating frequency up to 24MHz
• 3.3V power supply
• 768-byte RAM; 64K-byte program Flash memory
• Maximum 6 channels of PWM DAC
• Compliant with VESA DDC1/2B/2Bi/2B+/CI
standard
• Watchdog timer with programmable interval
• Support external counters/timers, T0, T1, and ET2
• Single/double frequency clock output
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
16

• Two clock output ports
• Two external interrupts, INT1 is shared with Slave
IIC interrupt source
• Maximum 4 channels of 6-bit ADC
• Flash-ROM code protection selection
• Hardware ISP (In System Programming), no Boot
Code required
• Embedded Dual Ports DDCRAM (128-byte x 2
• Green products like Pb-Free Packages or All Green Packages available
PIN CONFIGURATION & DESCRIPTION
A “CMOS output pin” means it can sink and drive at least 4mA current. It is not recommended
to use such pin as input function.
An “open drain pin” means it can sink at least 4mA current. It can be used as input or output
function and needs an external pull up resistor.
An “8051 standard pin” is a pseudo open drain pin. It can sink at least 4mA current when
output is at low level, and drives at least 4mA current for 160nS when output transits from low
to high, then keeps driving at 120 uA to maintain the pin at high level. It can be used as input
or output function. It needs an external pull up resistor when driving heavy load device.
There is an internal pull-up resistance on each CMOS PAD and an internal pull-down
resistance on each input
Low Power Reset (LVR) & Watchdog Timer
When the voltage level of power supply is below 2.4V (+/-0.4V) for a specific period of time,
the LVR generates a chip reset signal. After the power supply is above 2.4V (+/-0.4V)
INVERTER
In order to drive the CCFLs embedded in the panel module, there is a half bridge inverter to
convert by the controller.
The input 12V up to hundreds of AC voltage output.
The inverter is formed by symmetric in order to drive the separate lamp modules.
The input stage consists of a PWM controller, half bridge inverter, and switching MOSFET to
convert DC input into AC output.
The output stage consists of a tuning capacitor, coupling capacitor, transformer, push-pull
MOSFET pair to boost AC output up to hundreds of voltage.
And one resister is serial to lamp for output voltage feedback.
There are two signal to control the inverter which come from system.
Logic “high” level which send to I901 is turn on the inverter.
BRI signal control brightness by DC level which was integral from PWM signal.
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
17

5. Adjusting Procedure
1. Function Test
1.1. Product
- 19” LCD Monitor
1.2. Test Equipment
- Color Video Signal & Pattern (or PC with SXGA resolution and a sound card)
1.3. Test Condition
Before function test and alignment, each LCD Monitor should be run-in and warmed up for
at least 30 minutes with the following conditions:
(a) In room temperature,
(b) With full-white screen, RGB, and Black
(c) With cycled display modes,
640*480 (H=43.27kHz, V=85Hz)
800*600 (H=53.7kHz, V=85Hz)
1024*768 (H=68.67kHz, V=85Hz)
1280*1024 (H=79.97kHz, V=75Hz)
1.4. Test Display Modes & Pattern
1.4.1 Compatible Modes
Item Timing
1 640 x 350 @ 70Hz, 31.5kHz
2 640 x 400 @ 60Hz, 31.5kHz
3 640 x 400 @ 70Hz, 31.5kHz
4 640 x 480 @ 50Hz, 24.7kHz
5 640 x 480 @ 60Hz, 31.5kHz
6 640 x 480 @ 67Hz, 35.0kHz
7 640 x 480 @ 72Hz, 37.9kHz
8 640 x 480 @ 75Hz, 37.5kHz
9 640 x 480 @ 85Hz, 43.27kHz
10 720 x 400 @ 70Hz, 31.5kHz
11 800 x 600 @ 56Hz, 35.1kHz
12 800 x 600 @ 60Hz, 37.9kHz
13 800 x 600 @ 75Hz, 46.9kHz
14 800 x 600 @ 72Hz, 48.1kHz
15 800 x 600 @ 85Hz, 53.7kHz
16 832 x 624 @ 75Hz, 49.7kHz
17 1024 x 768 @ 60Hz, 48.4kHz
18 1024 x 768 @ 70Hz, 56.5kHz
19 1024 x 768 @ 72Hz, 58.1kHz
20 1024 x 768 @ 75Hz, 60.0kHz
21 1024 x 768 @ 85Hz, 68.67kHz
22 1152 x 864 @ 75Hz, 67.5kHz
23 1152 x 870 @ 75Hz, 68.7kHz
24 1280 x 1024 @ 60Hz, 63.4kHz
25 1280 x 1024 @ 75Hz, 79.97kHz
26 1280x 720 @ 60Hz, 45kHz (HDTV)
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
18

1.4.2 Function Test Display Pattern
Item Test Content Pattern Specification Remark
1 Frequency &
Tracking
Fine Line Moire Eliminate visual wavy
noise.
Figure 1
2 Contrast/Brightness 16 Gray Scale 16 gray levels should be
distinguishable.
Figure 2
3 Boundary Horizontal & Vertical
Thickness
Horizontal and Vertical
osition of video should be
adjustable to be within the
screen frame.
Figure 3
4 RGB Color
Performance
RGB Color
Intensities
Contrast of each R, G, B,
color should be normal.
Figure 4,
5, 6
5 Screen Uniformity &
Flicker
Full White Should be compliant with
the spec.
Figure 7
6 Dead Pixel/Line White Screen & Dark
Screen
The numbers of dead
pixels should be compliant
with the spec.
Figure 7,
8
7 White Balance White & Black
Pattern
The screen must have the
pure white and black
pattern, no other color.
Figure 9
Fine Line Morie Pattern (Figure1) Gray Scale Pattern (Figure2)
Horizontal & Vertical Thickness Pattern (Figure 3) R. Color Pattern (Figure 4)
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
19

G. Color Pattern (Figure5) B. Color Pattern (Figure 6)
Full White Patter (Figure 7) Dark Screen Pattern (Figure 8)
Black-White Pattern (Figure 9)
1.5. Function Test and Alignment Procedure
1.5.1 All Modes Reset
You should do “All Mode Reset” (Refer to Chapter III-3. Hot Keys for Function
Controls) first. This action will allow you to erase all end-user’s settings and restore the
factory defaults.
1.5.2 Auto Image Adjust
Please select and enter “Auto Image Adjust” function on Main Menu to see if it is
workable. The “Auto Image Adjust” function is aimed to offer a better screen quality
by built-in ASIC. For optimum screen quality, the user has to adjust each function
manually.
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
20

1.5.3 Firmware
Test Pattern: Burn In Mode (Refer to Chapter III-3. Hot Keys for Function Controls)
- Make sure the F/W is the latest version.
1.5.4 DDC
Test Pattern: EDID program
- Make sure it can pass test program.
1.5.5 Fine Tune and Sharpness
Test Signal: 1280*1024@60Hz
Test Pattern: Line Moire Pattern
- Check and see if the image has noise and focus performs well. Eliminate visual line
bar.
- If not, readjust by the following steps:
(a) Select and enter “Fine Tune” function on “Manual Image Adjust” to adjust the
image to eliminate visual wavy noise.
(b) Then, select and enter “Sharpness” function to adjust the clarity and focus of the
screen image.
1.5.6 Boundary
Test Signal: 1280*1024@60Hz
Test Pattern: Horizontal & Vertical Line Thickness Pattern
- Check and see if the image boundary is within the screen frame.
- If not, readjust by the following steps:
(a) Select and enter “Manual Image Adjust” function on OSD Main Menu.
(b) Then, select and enter “Horizontal Size” or “Horizontal/Vertical Position”
function to adjust the video boundary to be full scanned and within screen frame.
1.5.7 White Balance
A. TIMING: 1280x1024 64KHz/60Hz.
B. PATTERN: 5 Blocks.
C. LCD MONITOR set to 1280x1024 80K/75Hz BURN IN and warm up over 30
minutes.
D. CA110 color analizer at the center of screen and along a perpendicular to the
screen at 20cm from the display.
E. Power turn off, Press
“▲” and “ ”
and turn on power at the same time after
power LED is on, release
“▲” and “ ”
key, Then press “ ” key go to
factory mode. (Fig.1)
2
2
1
(Fig.1)
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
21

F. Adjust Color Temperature:
(1) EEPROM INIT (5 BLOCKS):
Press “▼ ” key move cursor to EEPROM INIT, Press “ “ key then
monitor will INIT ADC value.
2
(2) Press “▲” key move cursor to “White Balance”, Press “ “ key do
white balance adjustment.
2
(3) Press “▼ ” key move cursor to “Color Temperature Adjust”, Press
“ “ key, Then OSD will display Fig.2
2
(4) 9300K verify: move cursor to 9300K Press “ “ key.
(Fig.2)
Press “▼”, “▲” key adjust R.G.B value
2
x=0.283 ± 0.02
y=0.298 ± 0.02
Press “ “ key return to Fig.2
1
(5) 6500K verify: Repeat (4) press “▼”, “▲” move cursor to 6500K press
“ “ key
x=0.313 ± 0.02
2
y=0.329
± 0.02
(6) 5400K verify: Repeat (4) press “▼”, “▲” move cursor to 5400K press
“ “ key
x=0.332 ± 0.02
2
y=0.348 ± 0.02
(7) Press “ “ key go back to Fig.2, Then press “ “ key return to Fig.1,
Power key OFF/ON quit factory mode.
1 1
G. Color Temperature & Luminance Verify:
BRIGHTNESS MAX, CONTRAST MAX
9300K: x=0.283
± 0.02 y=0.298 ± 0.02
6500K: x=0.313 ± 0.02 y=0.329 ± 0.02
5400K: x=0.332
± 0.02 y=0.348 ± 0.02
1.5.8 R, G, B, Colors Contrast
Test Signal: 1280*1024@60Hz
Test Pattern: R, G, B, Color Intensities Pattern and 16 Gray Scale Pattern
- Check and see if each color is normal and distinguishable.
- If not, please return the unit to repair area.
1.5.9 Screen Uniformity and Flicker
Test Signal: 1280*1024@60Hz
Test Pattern: Full White Pattern
- Check and see if it is in normal condition.
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
22

1.5.10 Dead Pixel and Line
Test Signal: 1280*1024@60Hz
Test Pattern: Dark and White Screen Pattern
- Check and see if there are dead pixels on LCD panel with shadow gauge and filter
film.
- The total numbers and distance of dead pixels should be compliant with the spec.
1.5.11 Mura
Test Pattern: White, RGB, Black, & Grey
Test Tool: 8% ND Filter
- Check if the Mura can pass 8% ND Filter.
1.5.13 Check for Secondary Display Modes
Test Signal:
Analog: 640*350@70Hz; 640*480@60HZ
720*400@70Hz; 800*600@60HZ/70HZ/75HZ
832*624@75Hz, 1024*768@60HZ/70HZ/75HZ
1280*1024@60/75Hz
- Normally when the primary mode 1280*1024@60Hz is well adjusted and compliant
with the specification, the secondary display modes will be great possible to be
compliant with the spec. But we still have to check with the general test pattern to
make sure every secondary is compliant with the specification.
1.5.14 All Modes Reset
After final QC step, we have to erase all saved changes again and restore the factory
defaults. You should do “All Mode Reset” again.
1.5.15 Power Off Monitor
Turn off the monitor by pressing “Power” button.
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
23

2. Firmware Upgrade Procedure
When you receive the returned monitor, please check whether the firmware version is the
latest. If not, please do the following procedures to upgrade it to the latest version.
2.1. Equipment Needed
- VA902/b-2 Monitor
- Fixture for Firmware Upgrade
- VGA Cable
- PC (Personal Computer)
- LPT Cable
- Firmware Upgrade Program
- One additional monitor for checking the program execution
Printer Por
LPT Cable
VGA Cable
!
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
24

!
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
28
Step 6: Download program finish
Pressing the OK Button to finish the download program procedure.
Trouble shooting:
If you find the status like the follow picture. Please check the following item.
a. The connecting status between PC and ISP board.
b. The connecting status between ISP status and Monitor.
Turn off the power of monitor (AC plug off ) and disconnect the D-Sub connector . To
connect the D-Sub connector and then turn on the power of monitor.(AC plug on)
If the test result shows “passed”, it means the connection is well. If not (failed), it
means the connection has problems. Then you need to check the setup procedure or
reboot the PC, or simply use another PC to do the firmware upgrade.

3.2. Setup Procedure
3.2.1 Connect VGA Card and DDC Card with RS-232 cable.
3.2.2 Barcode Reader connect with keyboard and PC keyboard port.
3.2.3 Connect RS-232 Cable and VA902(2) with VGA Cable.
(when key in DVI DDC information, use VGA transform to DVI port )
3.2.4 Connect Power Cord to VA902(2) Monitor.
3.3. DDC Key In Procedure
3.3.1 Run DDC.exe
3.3.2 Choose model number and conform the Time then Press “ENTER” key.
!
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
30

3. Disassembly of Hinge, Main Board, Keypad Board and Panel Unit
3.1 Unscrew 4 screws to remove Hinge.
Hinge
3.2. Unscrew 2 screws to remove Shielding Plate.
Shielding Plate
3.3. Unscrew 2 screws and disconnect the connector to remove VGA Cable.
VGA Cable
3.4. Unscrew 7 screws and disconnect the wires to remove Main Board.
Main Board
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
38

6. Trouble Shooting Flow Chart
START
CHECK
MAIN BOARD
5V OK?
3.3V
OK?
1.8V
OK?
Y
Y
CHECK POWER
OARD
OK?
CHECK I102 AND
ROUND CAP OK?
N
CHECK I104,
SUROUND CAP
BEAD OK?
CHECK I104 3.3V
UROUND CAP
OK?
N
CHECK I103,
SUROUND CAP
BEAD OK?
CHECK I103 1.8V
UROUND CAP
OK?
N
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
40

Rev: 1a
Serial No. Prefix: Q4Q
1
AC POWER CORD USA WALL 1.83M BLACK A-PC-0106-0121 2427130046P P951 1
2
AC POWER CORD GERMAN WALL 1.83M BLACK A-PC-0106-0138
P951 1
3
PCB ASS'Y BLOCK (MAIN) B-00004499 6201-7998909121 1
4
PCB ASS'Y BLOCK (CON) B-00003004 6202-7998908101 1
5
BEZEL ASS'Y ABS 94HB PS-7604B VA902 C-00004500 2603307892 1
6
CABI BACK ASSY VE910 ABS 94HB BLACK 4001 C-00003008 2603407576 1
7
STAND VE910 ABS 94HB BLACK 4001 PL-00003006 2028259301P 5B01 1
8
DUST COVER ABS 94HB ELECTROPLATE AL PL-00003034 2027260401P 5B20 1
9
I/O CABLE D15/C13 20276(4.5) 1.83M BLACK CB-00003009 2427501191P P961 1
10
GUARANT CARD VIEWSONIC VA721/VE910 QSG DC-00004478 2002310496P 6P84 1
11
CD-OWNER GUIDE VA902 WIZARD VS10715 AUO DC-00004501 2438501231P 6P80 1
12
LCD PANEL M190EN03-V3 (N GRADE) AUO E-00004502 2212009400P V901 RB 1
13
LCD PANEL M190EN03-V3 (A GRADE) AUO E-00004503 2212009401P V901 RA 1
14
CARTON BOX VA902 VS10715 TCO99 WORLD P-00004504 2011133005P 6P01 1
15
POLYFOAM VE910-EPS (L) P-00003014 2012179800P 6P20 1
16
POLYFOAM VE910 -EPS (R) P-00003015 2012179900P 6P21 1
Remark 1:
Above listed items are examples, supplier can expand the rows to add more necessary items.
Remark 2:
RECOMMENDED SPARE PARTS LIST (VA902-2)
Description
PC Board Assembly:
Cabinets:
ViewSonic Model Number: VS10715
All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by
ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
Accessories:
Documentation:
Electronic
Packing Material:
7. Recommented Spare Parts List
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
43

Item ECR/ECN ViewSonic P/N Ref.P/N Location Universal number# Q'ty
AC POWER CORD USA WALL 1.83M BLACK
BEZEL ASS'Y ABS 94HB MIDNIGHT GRAY VA902B
CABI BACK ASSY VE910-B ABS 94HB MIDNIGHT GRAY
STAND VE910-B ABS 94HB MIDNIGHT GRAY
DUST COVER ABS 94HB ELECTROPLATE AL
I/O CABLE D15/C13 20276(4.5) 1.83M BLACK
GUARANT CARD VIEWSONIC VA721/VE910 QSG
CD-OWNER GUIDE VA902 WIZARD VS10715 AUO
LCD PANEL M190EN03-V3 (N GRADE) AUO
LCD PANEL M190EN03-V3 (A GRADE) AUO
CARTON BOX VA902B VS10715 TCO99 WORLD
Remark 1:
Above listed items are examples, supplier can expand the rows to add more necessary items.
Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by
ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
Packing Material:
Documentation:
RECOMMENDED SPARE PARTS LIST (VA902b-2)
Description
Board Assembly:
Cabinets:
Electronic
ViewSonic Model Number: VS10715
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
44

ViewSonic Model Number: VS10715
Rev: 1a
Serial No. Prefix: Q4Q
FRONT BEZEL ABS 94HB PS-7604B VA902
LED INDIC.-PWR VE910 PMMA 94HB COLOR CLEAR
FUNCTION KEY ABS 94HB ELECTROPLATE AL
NAME PLATE VIEWSONIC E015-006 3-BIRD LOGO
NAME PLATE VIEWSONIC 3-BIRD LOGO TNP
NAME PLATE 38.00MM*5.90MM
METAL FITTG VE910 SECC T=0.8 FOR PANEL
SCREW,SPE L355 M3x6 DH NICKEL-PLATED
SCREW,SPE ISZZTER001A M3*6L MSWR17/FZMYI
SHIELD PLATE VE910 SPTE T=0.3
INSULATOR PC SHEET T=0.5 FR700 94V0
BUSHING RUBBER CR BLACK 94HB
BUSHING 10*15*7.5MM TAPE=T4000
BRACKET,FIX SECC T=0.8 VE910 ACINLET
CABI BACK VE910 ABS 94HB BLACK 4001
NAME PLATE VIEWSONIC E015-017
BRACKET,FIX JT198QP SECC 0.8T WALL MOUNT
SCREW,CSK+ SCREW CSK+ M4*7
SCREW,BND T+ M4X10(BND T+)
SCREW,BND T+ M4X12(BND T+) (BLK)
SCREW,B SPW+ 4X12(+)SWRM-3 ZMC2-C
BRACKET,FIX METAL PLATE 1.0MM KENSINGTON
BUSHING VE710 PLUG RUBBER
STAND VE910 ABS 94HB BLACK 4001
METAL FITTG VE910 SECC T=1.5 FOR STAND
FOOT PAD RUBBER O20*2TMM SQUARE GRAIN
DUST COVER ABS 94HB ELECTROPLATE AL
LABEL VIEWSONIC OPEN STAND LABEL-LCD
CARTON BOX VA902 VS10715 TCO99 WORLD
LABEL VA902 VS10715 (M) AUO
LABEL VIEWSONIC VA520 NUMBER STICKER
LABEL VA902 VS10715 SMALL LABEL
LABEL VIEWSONIC INSET PAGE-1280X1024
LABEL VIEWSONIC CONTAINER LABEL
LABEL 10*20 HI-POT TESTED OK
LABEL VSC HIGH VOLTAGE WARNING LABEL
LABEL VA902 VS10715 AUO TCO99
SERIAL LABEL VIEWSONIC LCD SERIAL LABEL
POLYETHY BAG 90CMX75CMX0.02t PE-LD
CD-OWNER GUIDE VA902 WIZARD VS10715 AUO
GUARANT CARD VIEWSONIC VA721/VE910 QSG
POLYETHY BAG 250mmX350mmX0.3t ADD>PE-LD<
HEAT SINK JT178DP SPTE T=1MM
HEAT SINK JT178DP 40L*35W*20H AL T=3
HEAT SINK JT178QP AL6063S-75 30*20*15
HEAT SINK JT198QP SPTE 0.8t 18x11X43
SPRING PLATE SPTE T=0.4MM (GROUND PLATE)
SCREW,BND T+ M3X8(BND T+)
55 E-C-0404-1841 2281447391P CAP CER CC 0.047u/ 50V Y5V P=5.0 Z T
C101 C102 C103 C104 C105 C106
CAP CER TC 33p/50V CH P=5.0 J T
CAP CER TC 220p/50V CH P=5.0 J T
58 E-C-0404-1815 2281410491P CAP CER CC 0.1u/ 50V Y5V P=5.0 Z T
C109 C113 C114 C116 C118 C119
CAP ELE 105'C EC 47u/ 16V 5*11 P=5.0 T
CAP ELE 105'C EC 100u/ 16V 6.3*11 P=5.0 T
CAP ELE 105'C EC 4.7u/ 50V 5*11 P=5.0 T
CAP CER TC 10p/50V CH P=5.0 J T
CAP ELE 105'C EC 1u/ 50V 5*11 P=5.0 T
CAP ELE 105'C EC 10u/ 50V 5*11 P=5.0 T
65 #N/A 2300947401P CAP,MTL MINI X2 0.47u/275V P=15.0 M C
C801 RA
CAP CER Y2 4700p/250V Y5V P=10.0 M K
EC HI-RIPPLE 105C 400V EC 100u/400V 18*32 P=7.5 S
CAP CER CC 1000P/1KV Y5P P=5.0 K T
69 E-C-0404-4833 2281110491P CAP CER CC 0.1u/50V (Y5P) P=5.0 K T
C807 C832 C845 C910 C917 C923
CAP CER CC 180p/50V (Y5P) P=5.0 K T
CAP ELE 105'C EC 22u/ 50V 5*11 P=5.0 T
CAP CER CC 6800pF/50V K T
CAP CER CC 2200pF/1KV P=5.0 K T
CAP ELE SPECIAL (3000HR) EC 1500u/ 16V 13*16 P=5.0 C
CAP ELE SPECIAL (3000HR) EC 1500u /16V 13*20 P=5.0 C
CAP ELE SPECIAL EC 470u /16V 10*13 P=5.0 T
CAP ELE SPECIAL EC 1000u/ 10V 8*20 P=3.5 C
BOM LIST (VA902-2 for P-Region)
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
45

CAP,MTL MEF 4700pF/50V P=5.0 J T
CAP,MTL MEF 0.1uF/50V P=5.0 J T
CAP CER TC 22pF/3KV CH J P=7.5 C
CAP CER CC 1000p/50V X7R P=5.0 K T
CAP CER TC 5P/3KV SL P=7.5 J C
CAP CER CC 0.01u/50V X7R P=5.0 K T
CAP,MTL MEF 3900pF/50V P=5.0 J T
CAP,MTL MEF 0.068u/50V P=5.0 J T
CAP CER TC 47p/50V CH P=5.0 J T
CAP CER TC 330p/50V CH P=5.0 J T
CAP,MTL MEF 0.01uF/50V P=5.0 J T
CAP ELE 105'C EC 33u/ 25V 5*11 P=5.0 T
90 E-D-0403-0531 2363600195P DIODE,SWITCH 1N4148 DO-35
D101 D102 D103 D104 D105 D106
D107 D108 D809 D813 D902 D905
D906 D907 D908 D910 D911 D913
D914 D915 D917 D919 D912 D918
24
91 #N/A 2363219095P DIODE,RECT (EOL) 1N4002 DO-41 NI
D109 RA
2
92 #N/A 2363234495P DIODE,RECT 1N4002-FG DO-41 WILLAS
D109 RB
2
93 #N/A 2363200895P DIODE,RECT 1N4002 100V/1A DO-41 TSC
D109 RC
2
94 #N/A 2363214695P DIODE,RECT 1N4002F DO-41 FAGOR
D109 RD
96 E-D-0403-1500 2363222195P DIODE,RECT SB140 DO-41 PEC
D112 RB
RECT,BRIDGE 2KBP06M 600V/2A PEC
DIODE,RECT UF4007 DO-41 1000V/1A PEC
DIODE,RECT UF4007 DO-204AL GS
DIODE,RECT 1H5G-TG-WS R-1 WILLAS
DIODE,SWITCH 1U4G 400V/1A R-1 PEC
DIODE,ZENER MTZJ22B 20.64-21.71V ROHM
DIODE,ZENER HZ12A2-TA-E DO-35 RENESAS
DIODE,SCHOTTKY SRF10120C ITO-220AB MOSPEC
FUSE 21502.5(2.5A) LITTEL
FUSE FUSE 2.5A/250V SG501302.5 PICO
109 M-WR-0828-0478 2428106100P JUMPER 0.6∮*10.0mm
F901 J101 J110 J111 J116 J126
J802J903 J904 J906 J907 L801 R916
DIGITAL IC TSU16AS-LF SDIP-56 Mstar
MICRO-CONTROL IC MTV512GMN64 PDIP-40 MYSON
LINEAR IC AIC1117A-18PY SOT223 AIC
LINEAR IC CM1117GDCM223 SOT223 CHAMPION
IC,LINEAR(SMD) AP1117E18LA SOT-223 AnaChip
LINEAR IC AP1084T33L TO-220 Anachip
LINEAR IC AP1117T33L TO-220 Anachip
LINEAR IC AIC1084-33PT TO-220 AIC
IC,DIGITAL SMD 24LC16BT/SN SO-8 MICROCHIP
MEMORY IC AT24C16AN-10SU-2.7 SO-8 AMTEL
LINEAR IC LD7552-BS SOP-8 LEADTREND
PHOTO COUPLR TLP621 TOSHIBA
PHOTO COUPLR (EOL) TLP721F(D4-GR) TOSHIBA
LINEAR IC AP431VLA TO-92 ATC
LINEAR IC TL431CLPRE3 TO-92 TI
LINEAR IC KA431AZTA TO-92 FAIRCHILD
LINEAR IC CM431GDCN TO-92 CHAMPION
LINEAR IC OZ9932GN SOIC-8 O2-MICRO
LINEAR IC KA78L05AZ TO-92 FAIRCHILD
LINEAR IC L78L05ACZ-A/P TO-92 ST
LINEAR IC TS78L05CT TO-92 TSC
131 M-WR-0828-0450 2428106075P JUMPER 0.6∮*7.5mm
J102 J103 J105 J107 J112J113 J114
J115 J117 J118 J119 J120 J121 J122
J125 J127 J801 J803 J804 J901 J902
CU SHIELDING TAPE W25*L60mm (AL)
COIL,CHOKE 5uH 7.8*10 2UEW 0.65mm/12.5Ts
COIL,CHOKE ET-20 45mH 2UEW 0.26mm/55+55Ts
CONNECTOR JST PH 13P TOP P=2.0 OR EQUAL
CONNECTOR CF10301D0T0 CVILUX
CONNECTOR JST PH 8P TOP P=2.0 OR EQUAL
WIRE HARNESS 8/8P H/B 1061#26 L=200mm P=2.0
CONNECTOR 87210-0236 P=3.5 ACE OR EQUAL
AC POWER CORD USA WALL 1.83M BLACK
I/O CABLE D15/C13 20276(4.5) 1.83M BLACK
FFC CABLE FFC 30P*0.5mm*L80mm
EYELET BSS3-1/2H T=0.25 SN 3uM
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
46

150 E-Q-0402-0718 2361316191P XISTOR,NPN R 2PC945P TO-92 PHILIPS
Q101 RA
Q806 RA
3
151 E-Q-0402-0555 2361313691P XISTOR,NPN R KSC945CGTA TO-92 FAIRCHILD
Q101 RB
Q806 RB
3
152 E-Q-0402-0428 2361302591P XISTOR,NPN R 2SC945-AP TO-92 NEC
Q101 RC
Q806 RC
FET,P-CH SMD AP2305GN SOT23 APEC
FET,P-CH SMD (EOL) AO3411 SOT-23 AOS
155 E-Q-0402-1607 2360100596P XISTOR,PNP R SMD MMBT3906-NL SOT23 FAIRCHILD
Q103 RA
2
156 E-Q-0402-1607 2360100796P XISTOR,PNP R SMD MMBT3906 SOT23 DIODES
Q103 RB
2
157 #N/A 2360100696P XISTOR,PNP R SMD PMBS3906 SOT-23 PHILIPS
Q103 RC
2
158 E-Q-0402-1375 2360100396P XISTOR,PNP R SMD MMBT3906-7 SOT23 VISHAY
Q103 RD
2
159 #N/A 2360100896P XISTOR,PNP R SMD MMBT3906LT1G SOT-23 ON
Q103 RE
FET,N-CH AP04N70BF-H(LF) TO-220FM APEC
FET,N-CH AP04N70BF-A(LF) TO-220FM APEC
XISTOR,NPN A MPS3904 SOT-54 PHILIPS
XISTOR,PNP A MPS3906 SOT-54 PHILIPS
XISTOR,PNP A 2N3906TA TO-92 FAIRCHILD
XISTOR,PNP R 2PA733P TO-92 PHILIPS
XISTOR,PNP R KSA733-G TO-92 FAIRCHILD
XISTOR,PNP R 2SA733-AP-TP TO-92 NEC
FET,N-CH(SMD) AP9977GM SO-8 APEC
FET,N-CH 2N7000TA TO-92 FAIRCHILD
RES,PRE 1/4 S RN 1/4WS 75.00 F T52 MINI
171 E-R-0405-3216 2233447095P RES,CBN 1/4 S RD 1/4WS 47 ohm J T52
R104 R105 R106 R107 R108 R109
RES,CBN 1/4 S RD 1/4WS 2.2Kohm J T52
RES,CBN 1/4 S RD 1/4WS 75.00 J T52 MINI
RES,CBN 1/4 S RD 1/4WS 100 ohm J T52
RES,CBN 1/4 S RD 1/4WS 390 ohm J T52
176 E-R-0405-3214 2233410395P RES,CBN 1/4 S RD 1/4WS 10Kohm J T52
R117 R127 R128 R32 R133 R135
RES,CBN 1/4 S RD 1/4WS 4.7Kohm J T52
RES,CBN 1/4 S RD 1/4WS 200 ohm J T52
RES,CBN 1/4 S RD 1/4WS 1.0Mohm J T52
RES,CBN 1/4 S RD 1/4WS 470 ohm J T52
RES,CBN 1/4 S RD 1/4WS 560 ohm J T52
RES,MTL 1 RS 1W 1 ohm J P=15.0
THERMISTOR,PTH SCK-103 THINKING
RES,CBN 1/4 S RD 1/4WS 910Kohm J T52
RES,PRE 1/4 S RN 1/4WS 332Kohm F T52
RES,PRE 1/4 S RN 1/4WS 619Kohm F T52
RES,CBN 1/4 S RD 1/4WS 39 ohm J T52
RES,PRE 1/4 S RN 1/4WS 110Kohm F T52
RES MTL 2WS RS 2WS 0.604 ohm P=7.0 G
RES,CBN 1/4 S RD 1/4WS 3.3Kohm J T52
RES,MTL 1 RS 1WS 4.7ohm J P=12.5
RES,CBN 1/2WS RD 1/2WS 10 ohm J T52
RES,CBN 1/4 S RD 1/4WS 1Kohm J T52
RES,PRE 1/4 S RN 1/4WS 24.3Kohm F T52
RES,PRE 1/4 S RN 1/4WS 1.82Kohm F T
RES,CBN 1/4 S RD 1/4WS 5.6Kohm J T52
RES,PRE 1/4 S RN 1/4WS 1.58Kohm F T52
RES,PRE 1/4 S RN 1/4WS 1Kohm F T52
RES,PRE 1/4 S RN 1/4WS 91.0Kohm F T52
RES,CBN 1/4 S RD 1/4WS 820 ohm J T52
RES,CBN 1/4 S RD 1/4WS 100Kohm J T52
RES,CBN 1/4 S RD 1/4WS 1.8Kohm J T52
RES,PRE 1/4 S RN 1/4WS 10Kohm F T
HIGH VOLTAGE RESISTOR RD 1/2W 1.5Mohm J T52
RES,CBN 1/4 RD 1/4W 10 ohm J T
RES,PRE 1/4 S RN 1/4WS 2.0Kohm F T52
RES,CBN 1/4 S RD 1/4WS 270 ohm J T52
RES,PRE 1/4 S RN 1/4WS 453 ohm F T
RES,PRE 1/4 S RN 1/4WS 787 ohm F T
RES,CBN 1/4 S RD 1/4WS 5.1Kohm J T52
RES,CBN 1/4 S RD 1/4WS 5.1Mohm J T
RES,PRE 1/4 S RN 1/4WS 51.1Kohm F T52
RES,CHIP NETWORKS 8P4R 1/16W 10Kohm J P=0.8
RES,CHIP NETWORKS 8P4R 1/16W 100 ohm J P=0.8
RES,CHIP NETWORKS 8P4R 1/16W 2.7Kohm J P=0.8
RES,CHIP NETWORKS 8P4R 1/16W 4.7Kohm J P=0.8
TACT SWITCH TSTA-2 4.3mm 160g HUA-JIE
SOCKET 0711-02-P10-9 INALWAYS
SOCKET SC-8R-F15A9 SUPERCOM
220 #N/A 2407200991P HOLDER,FUSE CQ-05T CONQUER
S802 RA
2
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
47

221 M-MS-0808-1313 2407200791P HOLDER,FUSE FC-05C
S802 RB
XFORMER,POWR PT-003701-1 LAI-TAI
XFORMER INVERTER EEL-19 22/2000Ts 0.1*20/0.06mm
PC BOARD JT178QP4D M/B FR1 228*145 2.01
PC BOARD VE910 K/B FR1 120*23.5 V1.00
LCD PANEL M190EN03-V3 (N GRADE) AUO
LCD PANEL M190EN03-V3 (A GRADE) AUO
XTAL,OSC 12.0000MHZ/49US 0.1mW/30pF
DIODE,ZENER HZ6B-2 5.6-5.9V DO-35 HITACHI
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
48

FRONT BEZEL ABS 94HB MIDNIGHT GRAY VA902B
2 PL-00003024 2053754700P
LED INDIC.-PWR VE910 PMMA 94HB COLOR CLEAR
3 PL-00003025 2044267101P
FUNCTION KEY ABS 94HB ELECTROPLATE AL
4 M-MS-0808-9214 2051352100P
NAME PLATE VIEWSONIC E015-006 3-BIRD LOGO
NAME PLATE VIEWSONIC 3-BIRD LOGO TNP
NAME PLATE 38.00MM*5.90MM
7 HW-00003026 2071974300P
METAL FITTG VE910 SECC T=0.8 FOR PANEL
8 M-SCW-0824-6715 2080002200P
SCREW,SPE L355 M3x6 DH NICKEL-PLATED
9 M-SCW-0824-0811 2080003700P
SCREW,SPE ISZZTER001A M3*6L MSWR17/FZMYI
10 HW-00003027 2071673800P
SHIELD PLATE VE910 SPTE T=0.3
11 M-SCW-0824-6719 2082630062P
12 M-00003862 2072460100P
INSULATOR PC SHEET T=0.5 FR700 94V0
BUSHING RUBBER CR BLACK 94HB
BUSHING 10*15*7.5MM TAPE=T4000
16 HW-00003028 2071874300P
BRACKET,FIX SECC T=0.8 VE910 ACINLET
17 C-00003030 2022263502P
CABI BACK VE910-B ABS 94HB MIDNIGHT GRAY
18 M-MS-0808-9396 2051352202P
NAME PLATE NAME PLATE VIEWSONIC E015-027
19 HW-00003031 2071872900P
BRACKET,FIX JT198QP SECC 0.8T WALL MOUNT
20 HW-00003032 2106657000P
21 M-SCW-0824-0851 2082340072P
SCREW,CSK+ SCREW CSK+ M4*7
22 M-SCW-0824-0123 2084740102P
SCREW,BND T+ M4X10(BND T+)
23 M-SCW-0824-6944 2084740124P
SCREW,BND T+ M4X12(BND T+) (BLK)
24 M-SCW-0824-6746 2087340126P
SCREW,B SPW+ 4X12(+)SWRM-3 ZMC2-C
25 M-BK-0805-0070 2071869400P
BRACKET,FIX METAL PLATE 1.0MM KENSINGTON
26 M-SCW-0824-0285 2084730082P
SCREW,BND T+ M3X8(BND T+)
27 M-MS-0808-9408 2061453400P
BUSHING VE710 PLUG RUBBER
28 PL-00004517 2028259302P
STAND VE910-B ABS 94HB MIDNIGHT GRAY
29 HW-00003033 2071974400P
METAL FITTG VE910 SECC T=1.5 FOR STAND
30 PL-PD-0714-0113 2039819301P
FOOT PAD RUBBER O20*2TMM SQUARE GRAIN
31 M-SCW-0824-0285 2084730082P
SCREW,BND T+ M3X8(BND T+)
32 PL-00003034 2027260401P
DUST COVER ABS 94HB ELECTROPLATE AL
33 M-LB-0813-0769 2055613293P
LABEL VIEWSONIC OPEN STAND LABEL-LCD
34 P-00004812 2011133006P
CARTON BOX VA902B VS10715 TCO99 WORLD
LABEL VA902B VS10715(M) AUO
36 M-LB-0813-0855 2055613281P
LABEL VIEWSONIC VA520 NUMBER STICKER
LABEL VA902B VS10715 SMALL LABEL
38 DC-00001586 2055613435P
LABEL VIEWSONIC INSET PAGE-1280X1024
39 M-LB-0813-0856 2055613379P
LABEL VIEWSONIC CONTAINER LABEL
40 M-LB-0813-0530 2055617101P
LABEL 10*20 HI-POT TESTED OK
41 M-LB-0813-0959 2055613392P
LABEL VSC HIGH VOLTAGE WARNING LABEL
42 P-00003014 2012179800P
43 P-00003015 2012179900P
LABEL VA902B VS10715 AUO TCO99
45 M-LB-0813-0528 2055103400P
46 M-LB-0813-0002 2056603050P
SERIAL LABEL VIEWSONIC LCD SERIAL LABEL
47 M-MS-0808-1317 2013053000P
POLYETHY BAG 90CMX75CMX0.02t PE-LD
48 DC-00004501 2438501231P
CD-OWNER GUIDE VA902 WIZARD VS10715 AUO
49 DC-00003455 2002310496P
GUARANT CARD VIEWSONIC VA721/VE910 QSG
50 M-MS-0808-1316 2013222536P
POLYETHY BAG 250mmX350mmX0.3t ADD>PE-LD<
HEAT SINK JT178DP SPTE T=1MM
HEAT SINK JT178DP 40L*35W*20H AL T=3
HEAT SINK JT178QP AL6063S-75 30*20*15
HEAT SINK JT198QP SPTE 0.8t 18x11X43
SPRING PLATE SPTE T=0.4MM (GROUND PLATE)
56 M-SCW-0824-0285 2084730082P
SCREW,BND T+ M3X8(BND T+)
10
57 E-C-0404-1841 2281447391P CAP CER CC 0.047u/ 50V Y5V P=5.0 Z T
C105 C106 C110
7
58 E-C-0404-2980 2272133091P
CAP CER TC 33p/50V CH P=5.0 J T
59 E-C-0404-1119 2272122191P
CAP CER TC 220p/50V CH P=5.0 J T
60 E-C-0404-1815 2281410491P CAP CER CC 0.1u/ 50V Y5V P=5.0 Z T
C118 C119 C121 C122
10
61 #N/A 2333347691P
CAP ELE 105'C EC 47u/ 16V 5*11 P=5.0 T
62 E-C-0404-2271 2333310791P
CAP ELE 105'C EC 100u/ 16V 6.3*11 P=5.0 T
63 E-C-0404-1834 2333647591P
CAP ELE 105'C EC 4.7u/ 50V 5*11 P=5.0 T
64 E-C-0404-3092 2272110091P
CAP CER TC 10p/50V CH P=5.0 J T
65 E-C-0404-1424 2333610591P
CAP ELE 105'C EC 1u/ 50V 5*11 P=5.0 T
66 E-C-0404-1838 2333610691P
CAP ELE 105'C EC 10u/ 50V 5*11 P=5.0 T
67 #N/A 2300947401P CAP,MTL MINI X2 0.47u/275V P=15.0 M C
C801 RB
2
68 E-C-0404-1855 2287247212P
CAP CER Y2 4700p/250V Y5V P=10.0 M K
EC HI-RIPPLE 105C 400V EC 100u/400V 18*32 P=7.5 S
70 E-C-0404-2262 2285110291P
CAP CER CC 1000P/1KV Y5P P=5.0 K T
71 E-C-0404-4833 2281110491P CAP CER CC 0.1u/50V (Y5P) P=5.0 K T
C917 C923 C925 C928
8
72 #N/A 2281118191P
CAP CER CC 180p/50V (Y5P) P=5.0 K T
73 E-C-0404-1833 2333622691P
CAP ELE 105'C EC 22u/ 50V 5*11 P=5.0 T
CAP CER CC 6800pF/50V K T
CAP CER CC 2200pF/1KV P=5.0 K T
76 E-00003250 2330006601P
CAP ELE SPECIAL (3000HR) EC 1500u/ 16V 13*16 P=5.0 C
77 E-00003251 2330006701P
CAP ELE SPECIAL (3000HR) EC 1500u /16V 13*20 P=5.0 C
CAP ELE SPECIAL EC 470u /16V 10*13 P=5.0 T
79 E-00003252 2330006501P
CAP ELE SPECIAL EC 1000u/ 10V 8*20 P=3.5 C
80 E-00003555 2302047291P
CAP,MTL MEF 4700pF/50V P=5.0 J T
81 E-00003311 2302010491P
CAP,MTL MEF 0.1uF/50V P=5.0 J T
ViewSonic Model Number: VS10715
BOM LIST (VA902b-2)
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
49

CAP CER TC 22pF/3KV CH J P=7.5 C
CAP CER CC 1000p/50V X7R P=5.0 K T
CAP CER TC 5P/3KV SL P=7.5 J C
CAP CER CC 0.01u/50V X7R P=5.0 K T
CAP,MTL MEF 3900pF/50V P=5.0 J T
CAP,MTL MEF 0.068u/50V P=5.0 J T
88 E-C-0404-0287 2272147091P
CAP CER TC 47p/50V CH P=5.0 J T
89 E-C-0404-3470 2272133191P
CAP CER TC 330p/50V CH P=5.0 J T
CAP,MTL MEF 0.01uF/50V P=5.0 J T
CAP ELE 105'C EC 33u/ 25V 5*11 P=5.0 T
92 E-D-0403-0531 2363600195P DIODE,SWITCH 1N4148 DO-35
D105 D106 D107 D108
D809 D813 D902 D905
D906 D907 D908 D910
D911 D913 D914 D915
24
93 #N/A 2363219095P DIODE,RECT (EOL) 1N4002 DO-41 NI
D110 RA
2
94 #N/A 2363234495P DIODE,RECT 1N4002-FG DO-41 WILLAS
D110 RB
2
95 #N/A 2363200895P DIODE,RECT 1N4002 100V/1A DO-41 TSC
D110 RC
2
96 #N/A 2363214695P DIODE,RECT 1N4002F DO-41 FAGOR
D110 RD
2
97 E-D-0403-1297 2363220895P
98 E-D-0403-1500 2363222195P DIODE,RECT SB140 DO-41 PEC
D909 D916
3
99 #N/A 2363703891P
RECT,BRIDGE 2KBP06M 600V/2A PEC
DIODE,RECT UF4007 DO-41 1000V/1A PEC
DIODE,RECT UF4007 DO-204AL GS
DIODE,RECT 1H5G-TG-WS R-1 WILLAS
DIODE,SWITCH 1U4G 400V/1A R-1 PEC
105 E-D-0403-0254 2363507995P
DIODE,ZENER MTZJ22B 20.64-21.71V ROHM
106 E-D-0403-1532 2363505995P
DIODE,ZENER HZ12A2-TA-E DO-35 RENESAS
DIODE,SCHOTTKY SRF10120C ITO-220AB MOSPEC
109 E-FS-0410-0009 2213125207P
FUSE 21502.5(2.5A) LITTEL
110 E-FS-0410-0102 2213125211P
FUSE FUSE 2.5A/250V SG501302.5 PICO
111 M-WR-0828-0478 2428106100P JUMPER 0.6∮*10.0mm
J116 J126 J802J903 J904
J906 J907 L801 R916
14
112 #N/A 2365424900P
DIGITAL IC TSU16AS-LF SDIP-56 Mstar
MICRO-CONTROL IC MTV512GMN64 PDIP-40 MYSON
LINEAR IC AIC1117A-18PY SOT223 AIC
LINEAR IC CM1117GDCM223 SOT223 CHAMPION
IC,LINEAR(SMD) AP1117E18LA SOT-223 AnaChip
LINEAR IC AP1084T33L TO-220 Anachip
LINEAR IC AP1117T33L TO-220 Anachip
LINEAR IC AIC1084-33PT TO-220 AIC
120 E-IC-0401-2269 2365915896P
IC,DIGITAL SMD 24LC16BT/SN SO-8 MICROCHIP
MEMORY IC AT24C16AN-10SU-2.7 SO-8 AMTEL
LINEAR IC LD7552-BS SOP-8 LEADTREND
123 E-PC-0411-0083 2362401800P
PHOTO COUPLR TLP621 TOSHIBA
124 E-PC-0411-0082 2362401600P
PHOTO COUPLR (EOL) TLP721F(D4-GR) TOSHIBA
LINEAR IC AP431VLA TO-92 ATC
126 E-IC-0401-1270 2365319391P
LINEAR IC TL431CLPRE3 TO-92 TI
127 E-IC-0401-2152 2365321991P
LINEAR IC KA431AZTA TO-92 FAIRCHILD
LINEAR IC CM431GDCN TO-92 CHAMPION
LINEAR IC OZ9932GN SOIC-8 O2-MICRO
LINEAR IC KA78L05AZ TO-92 FAIRCHILD
LINEAR IC L78L05ACZ-A/P TO-92 ST
LINEAR IC TS78L05CT TO-92 TSC
133 M-WR-0828-0450 2428106075P JUMPER 0.6∮*7.5mm
J112J113 J114 J115 J117
J118 J119 J120 J121
J122 J125 J127 J801
J803 J804 J901 J902
25
134 M-WR-0828-0460 2428106125P
135 M-MS-0808-0856 2428106200P
136 M-WR-0828-0455 2428106050P
137 M-WR-0828-0451 2428106150P
CU SHIELDING TAPE W25*L60mm (AL)
139 E-L-0407-0013 2379101495P
COIL,CHOKE 5uH 7.8*10 2UEW 0.65mm/12.5Ts
COIL,CHOKE ET-20 45mH 2UEW 0.26mm/55+55Ts
142 E-L-0407-0976 2379101491P
CONNECTOR JST PH 13P TOP P=2.0 OR EQUAL
CONNECTOR CF10301D0T0 CVILUX
CONNECTOR JST PH 8P TOP P=2.0 OR EQUAL
WIRE HARNESS 8/8P H/B 1061#26 L=200mm P=2.0
CONNECTOR 87210-0236 P=3.5 ACE OR EQUAL
148 A-PC-0106-0138 2427130047P
AC POWER CORD GERMAN WALL 1.83M BLACK
149 CB-00003009 2427501191P
I/O CABLE D15/C13 20276(4.5) 1.83M BLACK
FFC CABLE FFC 30P*0.5mm*L80mm
151 M-00003554 2097400301P
EYELET BSS3-1/2H T=0.25 SN 3uM
152 E-Q-0402-0718 2361316191P XISTOR,NPN R 2PC945P TO-92 PHILIPS
Q806 RA
Q901 RA
3
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
50

153 E-Q-0402-0555 2361313691P XISTOR,NPN R KSC945CGTA TO-92 FAIRCHILD
Q806 RB
Q901 RB
3
154 E-Q-0402-0428 2361302591P XISTOR,NPN R 2SC945-AP TO-92 NEC
Q806 RC
Q901 RC
3
155 #N/A 2360501396P
FET,P-CH SMD AP2305GN SOT23 APEC
FET,P-CH SMD (EOL) AO3411 SOT-23 AOS
157 E-Q-0402-1607 2360100596P XISTOR,PNP R SMD MMBT3906-NL SOT23 FAIRCHILD
Q104 RA
2
158 E-Q-0402-1607 2360100796P XISTOR,PNP R SMD MMBT3906 SOT23 DIODES
Q104 RB
2
159 #N/A 2360100696P XISTOR,PNP R SMD PMBS3906 SOT-23 PHILIPS
Q104 RC
2
160 E-Q-0402-1375 2360100396P XISTOR,PNP R SMD MMBT3906-7 SOT23 VISHAY
Q104 RD
2
161 #N/A 2360100896P XISTOR,PNP R SMD MMBT3906LT1G SOT-23 ON
Q104 RE
2
162 #N/A 2361610900P
FET,N-CH AP04N70BF-H(LF) TO-220FM APEC
163 E-00004445 2361611200P
FET,N-CH AP04N70BF-A(LF) TO-220FM APEC
XISTOR,NPN A MPS3904 SOT-54 PHILIPS
XISTOR,PNP A MPS3906 SOT-54 PHILIPS
XISTOR,PNP A 2N3906TA TO-92 FAIRCHILD
167 E-Q-0402-0720 2361111491P
XISTOR,PNP R 2PA733P TO-92 PHILIPS
168 E-Q-0402-0962 2361110791P
XISTOR,PNP R KSA733-G TO-92 FAIRCHILD
169 E-Q-0402-1106 2361100491P
XISTOR,PNP R 2SA733-AP-TP TO-92 NEC
FET,N-CH(SMD) AP9977GM SO-8 APEC
FET,N-CH 2N7000TA TO-92 FAIRCHILD
172 E-R-0405-2776 2239207505P
RES,PRE 1/4 S RN 1/4WS 75.00 F T52 MINI
173 E-R-0405-3216 2233447095P RES,CBN 1/4 S RD 1/4WS 47 ohm J T52
R108 R109 R809 R853
8
174 E-R-0405-2367 2233422295P
RES,CBN 1/4 S RD 1/4WS 2.2Kohm J T52
5
175 E-R-0405-3429 2233475095P
RES,CBN 1/4 S RD 1/4WS 75.00 J T52 MINI
176 E-R-0405-1757 2233410195P
RES,CBN 1/4 S RD 1/4WS 100 ohm J T52
177 E-R-0405-3430 2233439195P
RES,CBN 1/4 S RD 1/4WS 390 ohm J T52
178 E-R-0405-3214 2233410395P RES,CBN 1/4 S RD 1/4WS 10Kohm J T52
R133 R135 R136 R162
10
179 E-R-0405-3211 2233447295P
RES,CBN 1/4 S RD 1/4WS 4.7Kohm J T52
180 E-R-0405-0645 2233420195P
RES,CBN 1/4 S RD 1/4WS 200 ohm J T52
181 E-R-0405-3213 2233410595P
RES,CBN 1/4 S RD 1/4WS 1.0Mohm J T52
182 E-R-0405-3215 2233447195P
RES,CBN 1/4 S RD 1/4WS 470 ohm J T52
183 E-R-0405-0078 2233456195P
RES,CBN 1/4 S RD 1/4WS 560 ohm J T52
184 E-R-0405-6428 2235410903P
RES,MTL 1 RS 1W 1 ohm J P=15.0
185 E-TH-0416-0042 2229201212P
THERMISTOR,PTH SCK-103 THINKING
RES,CBN 1/4 S RD 1/4WS 910Kohm J T52
RES,PRE 1/4 S RN 1/4WS 332Kohm F T52
RES,PRE 1/4 S RN 1/4WS 619Kohm F T52
RES,CBN 1/4 S RD 1/4WS 39 ohm J T52
RES,PRE 1/4 S RN 1/4WS 110Kohm F T52
191 E-00003249 2236560476P
RES MTL 2WS RS 2WS 0.604 ohm P=7.0 G
192 E-R-0405-2306 2233433295P
RES,CBN 1/4 S RD 1/4WS 3.3Kohm J T52
RES,MTL 1 RS 1WS 4.7ohm J P=12.5
RES,CBN 1/2WS RD 1/2WS 10 ohm J T52
195 E-R-0405-3235 2233410295P
RES,CBN 1/4 S RD 1/4WS 1Kohm J T52
196 E-R-0405-2818 2239224325P
RES,PRE 1/4 S RN 1/4WS 24.3Kohm F T52
RES,PRE 1/4 S RN 1/4WS 1.82Kohm F T
198 E-R-0405-0063 2233456295P
RES,CBN 1/4 S RD 1/4WS 5.6Kohm J T52
RES,PRE 1/4 S RN 1/4WS 1.58Kohm F T52
200 E-R-0405-3034 2239210015P
RES,PRE 1/4 S RN 1/4WS 1Kohm F T52
RES,PRE 1/4 S RN 1/4WS 91.0Kohm F T52
202 E-R-0405-1171 2233482195P
RES,CBN 1/4 S RD 1/4WS 820 ohm J T52
203 E-R-0405-3221 2233410495P
RES,CBN 1/4 S RD 1/4WS 100Kohm J T52
204 E-R-0405-4713 2233418295P
RES,CBN 1/4 S RD 1/4WS 1.8Kohm J T52
205 E-R-0405-5980 2239210025P
RES,PRE 1/4 S RN 1/4WS 10Kohm F T
HIGH VOLTAGE RESISTOR RD 1/2W 1.5Mohm J T52
RES,CBN 1/4 RD 1/4W 10 ohm J T
208 E-R-0405-4534 2239220015P
RES,PRE 1/4 S RN 1/4WS 2.0Kohm F T52
209 E-R-0405-3526 2233427195P
RES,CBN 1/4 S RD 1/4WS 270 ohm J T52
RES,PRE 1/4 S RN 1/4WS 453 ohm F T
RES,PRE 1/4 S RN 1/4WS 787 ohm F T
212 E-R-0405-6218 2233451295P
RES,CBN 1/4 S RD 1/4WS 5.1Kohm J T52
RES,CBN 1/4 S RD 1/4WS 5.1Mohm J T
RES,PRE 1/4 S RN 1/4WS 51.1Kohm F T52
RES,CHIP NETWORKS 8P4R 1/16W 10Kohm J P=0.8
216 E-R-0405-6608 2259210108P
RES,CHIP NETWORKS 8P4R 1/16W 100 ohm J P=0.8
RES,CHIP NETWORKS 8P4R 1/16W 2.7Kohm J P=0.8
218 E-R-0405-6007 2259247208P
RES,CHIP NETWORKS 8P4R 1/16W 4.7Kohm J P=0.8
TACT SWITCH TSTA-2 4.3mm 160g HUA-JIE
SOCKET 0711-02-P10-9 INALWAYS
SOCKET SC-8R-F15A9 SUPERCOM
222 #N/A 2407200991P HOLDER,FUSE CQ-05T CONQUER
S803 RA
2
223 M-MS-0808-1313 2407200791P HOLDER,FUSE FC-05C
S803 RB
2
224 #N/A 2374228012P
XFORMER,POWR PT-003701-1 LAI-TAI
XFORMER INVERTER EEL-19 22/2000Ts 0.1*20/0.06mm
227 E-00003308 2202130701P
PC BOARD JT178QP4D M/B FR1 228*145 2.01
PC BOARD VE910 K/B FR1 120*23.5 V1.00
229 E-00004502 2212009400P
LCD PANEL M190EN03-V3 (N GRADE) AUO
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
51

ViewSonic Model Number: VS10715
Rev: 1a
Serial No. Prefix: Q4Q
Item ViewSonic P/N Ref. P/N Description Q'ty
1-1 #N/A 2024268703P FRONT BEZEL ABS 94HB PS-7604B VA902 1
1-2 #N/A 2024268704P FRONT BEZEL ABS 94HB MIDNIGHT GRAY VA902B 1
2 PL-00003024 2053754700P LED INDIC.-PWR VE910 PMMA 94HB COLOR CLEAR 1
3 PL-00003025 2044267101P FUNCTION KEY ABS 94HB ELECTROPLATE AL 1
4 HW-00003026 2071974300P METAL FITTG VE910 SECC T=0.8 FOR PANEL 1
5 M-SCW-0824-6715 2080002200P SCREW,SPE L355 M3x6 DH NICKEL-PLATED 4
6 M-SCW-0824-0811 2080003700P SCREW,SPE ISZZTER001A M3*6L MSWR17/FZMYI 7
7 M-SCW-0824-0811 2080003700P SCREW,SPE ISZZTER001A M3*6L MSWR17/FZMYI 1
8 HW-00003027 2071673800P SHIELD PLATE VE910 SPTE T=0.3 1
9 M-SCW-0824-6719 2082630062P SCREW M3X6 P=0.5 2
10 M-SCW-0824-0811 2080003700P SCREW,SPE ISZZTER001A M3*6L MSWR17/FZMYI 1
11 HW-00003028 2071874300P BRACKET,FIX SECC T=0.8 VE910 ACINLET 1
12-1 C-00003029 2022263501P CABI BACK VE910 ABS 94HB BLACK 4001 1
12-2 C-00003030 2022263502P CABI BACK VE910-B ABS 94HB MIDNIGHT GRAY 1
13 HW-00003031 2071872900P BRACKET,FIX JT198QP SECC 0.8T WALL MOUNT 1
14 HW-00003032 2106657000P HINGE VE910 -5'~+20'~90' 1
15 M-SCW-0824-0851 2082340072P SCREW,CSK+ SCREW CSK+ M4*7 4
16 M-SCW-0824-0123 2084740102P SCREW,BND T+ M4X10(BND T+) 1
17 M-SCW-0824-6944 2084740124P SCREW,BND T+ M4X12(BND T+) (BLK) 2
18 M-SCW-0824-6746 2087340126P SCREW,B SPW+ 4X12(+)SWRM-3 ZMC2-C 4
19 M-BK-0805-0070 2071869400P BRACKET,FIX METAL PLATE 1.0MM KENSINGTON 1
20 M-SCW-0824-0285 2084730082P SCREW,BND T+ M3X8(BND T+) 2
21-1 PL-00003006 2028259301P STAND VE910 ABS 94HB BLACK 4001 1
21-2 PL-00003016 2028259302P STAND VE910-B ABS 94HB MIDNIGHT GRAY 1
22 HW-00003033 2071974400P METAL FITTG VE910 SECC T=1.5 FOR STAND 1
23 PL-PD-0714-0113 2039819301P FOOT PAD RUBBER O20*2TMM SQUARE GRAIN 5
24 M-SCW-0824-0285 2084730082P SCREW,BND T+ M3X8(BND T+) 5
25 PL-00003034 2027260401P DUST COVER ABS 94HB ELECTROPLATE AL 2
26-1 M-MS-0808-9215 2051352200P NAME PLATE VIEWSONIC E015-017 1
26-2 M-MS-0808-9396 2051352202P NAME PLATE VIEWSONIC E015-027 1
27 #N/A 2427408202P WIRE HARNESS 8/8P H/B 1061#26 L=200mm P=2.0 1
28 #N/A 2420306301P FFC CABLE FFC 30P*0.5mm*L80mm 1
EXPLODED PARTS LIST (VA902/b-2)
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
55

*Readers Response*
Dear Readers:
Thank you in advance for your feedback on our Service Manual, which allows continuous improvement
of our products. We would appreciate your completion of the Assessment Matrix below, for return to
ViewSonic Corporation.
Assessment
Readers basic data:
After completing this form, please return it to ViewSonic Quality Assurance
metI tnellecxE dooG riaF daB
.1
.2
.3
tinU riaF daB
in the USA at facsimile
1-909-839-7943.
You may also e-mail any suggestions to the Director, Quality Systems & Processes
(marc.maupin@viewsonic.com)
dooGtnellecxE
Precautions and Safety Notices
1.
8. Exploded Diagram and Exploded Parts List
7. Recommended Spare Parts List
Adjustment Procedure
2. Specification
5.
4. Circuit Description
3.
6. Troubleshooting Flow Chart
Front Panel Function Control Description
9. Block Diagram
10. Schematic Diagrams
11. PCB Layout Diagrams
Service Manual Content
Service Manual Layout
The form and listing
Name: Title:
Company:
Add.:
Tel:
E-mail:
Fax:
A. What do you think about the content of this Service Manual?
B. Are you satisfied with this Service Manual?
C. Do you have any other opinions or suggestions regarding this service manual?
View Sonic Corporation Confidential - Do Not Copy VA902-2_VA902b-2
68