ViewSonic SWB5501, SWB6552, SWB8451, SWB7051, CDE8451 User Manual

...

SWB5501/SWB6552/SWB7051/ SWB8451 Smart White Board

CDE5501/CDE6552/CDE7051/ CDE8451 LCD Display

User Guide

IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http://

www.viewsonic.com in English, or in specic languages using the Regional selection

box in the upper right corner of our website. “Antes de operar su equipo lea cu idadosamente las instrucciones en este manual”

Model No. VS15421/VS15432/VS15633/VS15420

Compliance Information

NOTE: This section addresses all connected requirements and statements regarding

regulations. Confirmed corresponding applications shall refer to nameplate labels and relevant markings on unit.

FCC Compliance Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

Industry Canada Statement

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2004/108/EC and Low Voltage Directive 2006/95/EC.

Following information is only for EU-member states:

The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE).The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste, but use the return and collection systems according to local law.

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Proposed Maximum Concentration

Actual Concentration

Lead (Pb) 0.1% < 0.1% Mercury (Hg) 0.1% < 0.1% Cadmium (Cd) 0.01% < 0.01% Hexavalent Chromium (Cr Polybrominated biphenyls

(PBB) Polybrominated diphenyl ethers

(PBDE)

) 0.1% < 0.1%

0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below:

Examples of exempted components are:

1. Mercury in cold cathode fluorescent lamps and external electrode fluorescent

lamps (CCFL and EEFL) for special purposes not exceeding (per lamp): (1) Short length (≦500 mm): maximum 3.5 mg per lamp.

(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp. (3) Long length (＞1,500 mm): maximum 13 mg per lamp.

2. Lead in glass of cathode ray tubes.

3. Lead in glass of fluorescent tubes not exceeding 0.2% by weight.

4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.

5. Copper alloy containing up to 4% lead by weight.

6. Lead in high melting temperature type solders (i.e. lead-based alloys containing

85% by weight or more lead).

7. Electrical and electronic components containing lead in a glass or ceramic other

than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.

Cautions and Warnings

1. Read these instructions completely before using the equipment.

2. Keep these instructions in a safe place.

3. Heed all warnings and follow all instructions.

4. Always handle the LCD display with care when moving it.

5. Never remove the rear cover. This LCD display contains high-voltage parts.

You may be seriously injured if you touch them.

6. Do not use this equipment near water. Warning: To reduce the risk of fire or

electric shock, do not expose this apparatus to rain or moisture.

7. Avoid exposing the LCD display to direct sunlight or another heat source. Orient

the LCD display away from direct sunlight to reduce glare.

8. Clean with a soft, dry cloth. If further cleaning is required, see the “Care and

Maintenance” section in this guide for further instructions.

9. Avoid touching the screen. Skin oils are difficult to remove.

10. Do not rub or apply pressure to the LCD panel, as it may permanently damage

the screen.

11. Do not block any ventilation openings. Install the equipment in accordance with

the manufacturer’s instructions.

12. Do not install near any heat sources such as radiators, heat registers, stoves, or

other devices (including amplifiers) that produce heat.

13. Place the LCD display in a well ventilated area. Do not place anything on the

LCD display that prevents heat dissipation.

14. Do not place heavy objects on the LCD display, video cable, or power cord.

15. If smoke, an abnormal noise, or a strange odor is present, immediately switch

the LCD display off and call your dealer or ViewSonic. It is dangerous to continue using the LCD display.

16. Do not attempt to circumvent the safety provisions of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade and the third prong are provided for your safety. If the plug does not fit into your outlet, consult an electrician for replacement of the outlet.

17. Protect the power cord from being tread upon or pinched, particularly at the plug,

and the point where if emerges from the equipment. Be sure that the power outlet is located near the equipment so that it is easily accessible.

18. Only use attachments/accessories specified by the manufacturer.

(Continued on next page)

iii

19. Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the equipment. When a cart is used, use caution when moving the cart/equipment combination to avoid injury from tipping over.

20. Unplug this equipment when it will be unused for long periods of time.

21. Refer all servicing to qualified service personnel. Service is required when the

unit has been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the unit does not operate normally or has been dropped.

Contents

Compliance Information

FCC Compliance Statement ................................................................ i

Industry Canada Statement ................................................................. i

CE Conformity for European Countries ............................................... i

Declaration of RoHS2 Compliance ......................................................ii

Cautions and Warnings ......................................................................iii

Product Registration ........................................................................... 2

For Your Records ............................................................................... 2

1. Getting Started

1.1 Package Contents ........................................................................ 3

1.2 Wall Mount Kit Specifications (VESA) .......................................... 4

2. Smart Whiteboard/LCD Display Features

2.1 Control Panel Overview ................................................................ 5

2.2 Terminal Interface Overview ........................................................ 8

2.3 Remote Control Overview .......................................................... 11

2.4 Inserting Remote Control Batteries ............................................ 13

2.5 Remote Control Receiver Range ............................................... 14

3. Setting Up Your Display

3.1 Connecting an External PC ........................................................ 15

3.2 RS232 Connections ................................................................... 18

3.3 Connecting USB Peripherals ...................................................... 19

3.4 AV IN Connections ..................................................................... 22

3.5 S-Video Connections .................................................................. 24

3.6 YPbPr Connections .................................................................... 25

3.7 HDMI Connections ..................................................................... 26

3.8 Microphone Connections ............................................................ 27

3.9 Coaxial Connections .................................................................. 28

3.10 VGA Connections ..................................................................... 29

3.11 AV OUT Connections ............................................................... 31

4. Basic Display Operations

5. OSD Menu Operation

5.1 Input Source ............................................................................... 33

5.2 Screen Menu .............................................................................. 37

5.3 Picture Menu .............................................................................. 39

5.4 Sound Menu (SWB5501/SWB6552/SWB7051/CDE5501/

CDE6552/CDE7051 Models) ..................................................... 41

5.5 Time Menu (SWB5501/SWB6552/SWB7051/CDE5501/

CDE6552/CDE7051 Models) ..................................................... 42

5.6 Lock Menu (SWB5501/SWB6552/SWB7051/CDE5501/

CDE6552/CDE7051 Models) ..................................................... 43

5.7 Setup Menu (SWB5501/SWB6552/SWB7051/CDE5501/

CDE6552/CDE7051 Models) ..................................................... 44

5.8 Annotation Menu (SWB8451/CDE8451 Models) ....................... 45

5.9 Android System Interface (SWB8451/CDE8451 Models) .......... 46

5.10 Multimedia File Playback Interface (SWB8451/CDE8451

Models) ..................................................................................... 51

6. Trouble Shooting

7. Care and Maintenance

8. Display Modes

8.1 YPbPr Mode ............................................................................... 57

8.2 VGA Mode .................................................................................. 57

8.3 HDMI Mode ................................................................................ 58

9. Specifications

10. RS-232 Protocol

10.1 Introduction ............................................................................... 60

10.2 Description ............................................................................... 60

10.2.1 Hardware specification .......................................................... 60

10.2.2 Communication Setting ......................................................... 61

10.2.3 Command Message Reference ............................................. 61

10.3 Protocol .................................................................................... 61

10.3.1 Set-Function Listing ............................................................... 61

10.3.2 Get-Function Listing .............................................................. 67

10.3.3 Remote Control Pass-through mode ..................................... 70

Other Information

Customer Support ............................................................................ 72

Limited Warranty .............................................................................. 73

Mexico Limited Warranty .................................................................. 75

vii

Copyright © ViewSonic Corporation, 2014. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft

Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered

trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association.

DPMS, DisplayPort, and DDC are trademarks of VESA.

is a trademark of SRS Labs, Inc.

Premium Sound technology is incorporated under license from SRS Labs, Inc. E

NERGY STAR

Agency (EPA). As an E

NERGY STAR

product meets the ENERGY STAR® guidelines for energy efficiency. Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors

or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.

is a registered trademark of the U.S. Environmental Protection

partner, ViewSonic Corporation has determined that this

In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change product specifications without notice. Information in this document may change without notice.

No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To fulfill possible future product needs, and to receive additional product information as it becomes available, please visit your region section on ViewSonic’s website to register your product online.

The ViewSonic CD also provides an opportunity for you to print the product registration form. Upon completion, please mail or fax to a respective ViewSonic office. To find your registration form, use the directory “:\CD\Registration”. Registering your product will best prepare you for future customer service needs.

Please print this user guide and fill the information in the “For Your Records” section. Your LCD displays serial number is located on the rear side of the display.

For additional information, please see the “Customer Support” section in this guide.

For Your Records

Product Name:

Model Number: Document Number:

Serial Number: Purchase Date:

Product disposal at end of product life

ViewSonic respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing.

Please visit ViewSonic website to learn more. USA & Canada: http://www.viewsonic.com/company/green/recycle-program/ Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/

SWB5501/SWB6552/SWB7051/SWB8451 ViewSonic Smart White Board CDE5501/CDE6552/CDE7051/CDE8451

ViewSonic LCD Display

VS15421/VS15432/VS15633/VS15420 SWB5501/SWB6552/SWB7051/SWB8451/CDE5501/ CDE6552/CDE7051/CDE8451_UG_ENG Rev. 1D 03-31-14 _______________________________________ _______________________________________

Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

1. Getting Started

Congratulations on your purchase of a ViewSonic® Smart Whiteboard/LCD display.

Important! Save the original box and all packing material for future shipping needs.

Note: The word “Windows” in this user guide refers to Microsoft Windows operating

system.

1.1 Package Contents

• Power cable

• VGA cable

• Remote control

• AAA battery x 2

• USB cable

• Audio cable

• Stylus pen x 3

• AV cable (for SWB6552/SWB7051/SWB8451/CDE6552/CDE7051/CDE8451

models only)

• YPbPr cable (for SWB6552/SWB7051/CDE6552/CDE7051 models only)

• Wall mount installation guide

• User manual CD wizard

- User Guide

- ViewBoard software

1.2 Wall Mount Kit Specifications (VESA)

Please follow the instructions in the wall mount installation guide to install your wall mount or mobile mount bracket. If attaching to other building materials, please contact your nearest dealer.

inch VESA Spec. (A x B) Standard Screw (C x D) Quantity 55 400 x 400 mm M8 x L40 4 65 600 x 400 mm M8 x L40 4 70 600 x 600 mm M8 x L40 4 84 600 x 600 mm M8 x L40 8

• ViewSonic provides the standard dimensions for wall mount kits as shown in the

table above.

• To find the perfect mount, please browse www.viewsonic.com or call our service team: United States 1-800-688-6688, Canada 1-866-463-4775.

• When purchasing our wall mount kit, a detailed install manual and all parts

necessary for assembly are provided.

• Do not use the screws that longer than the standard dimension, as they may cause damage to the inside of the LCD display set.

2. Smart Whiteboard/LCD Display Features

This section introduces you to the features of your Smart Whiteboard/LCD Display.

Note: The features or applications described in this User’s manual may vary depending on the device model purchased.

2.1 Control Panel Overview

SWB5501/CDE5501 Control Panel:

Item Description

INPUT

CH.

VOL+/-

RC Receiver

Power Indicator

Power On/Off

Switch between different sources

OSD Menu On/Off

Move upward/downward to scroll through menu options.

Increase or decrease volume

Receives signals from the remote control

Indicates power status (On/Off)

SWB6552/SWB7051/CDE6552/CDE7051 Control Panel:

ENERGY

SAVING

ZOOM VOL- VOL+ PC/VGA

INPUT

PC USB

Item Description

Power On / Off switch

INPUT Switch to different source PC/VGA Switch between PC and VGA sources VOL+/- Increase or decrease volume ZOOM Adjust screen ratio ENERGY SAVING Energy-saving mode PC USB Internal PC USB port RC Receiver Receives signals from the remote control Power Indicator Indicates power status (On / Off)

PC USB

SWB8451/CDE8451 Control Panel:

Item Description

Press the key to turn on the device Press the key to turn on/off the screen Press and hold the key to turn off the device

Back to Android main interface Return to Android previous level Call up function menu Decrease volume Increase volume Internal PC USB port Display USB port for Android system Receives signals from the remote control

2.2 Terminal Interface Overview

SWB5501/CDE5501 Interface:

Item Description

AUDIO OUT MIC

USB IN

VGA OUT LAN IN

USB IN

HDMI S-VIDEO COAXIAL AUDIO IN VGA IN AV OUT TOUCH OUT AV IN COMPONENT

Connects the device to headphones or speakers Connects to a microphone

Connects USB peripherals such as HDDs USB keyboards, mice and more

Connects the display with the VGA-IN connector Standard RJ45 (10M/100M/1G) Internet connection interface Display Motherboard Upgrade Interface High Definition Multimedia Interface S-VIDEO input Coaxial output Connects the device to external audio sources Connects the device to external video sources Audio-Video output port External PC touch-signal input Audio-Video combined input port YPbPr signal input, connect DVD, set -top -box with YPbPr

RS232 AC IN POWER

Note: Model nos. CDE5501 do not have interface features #1 – 5 if the optional slot-in PC module is not installed.

Serial port interface AC power input Power On / Off switch

SWB6552/SWB7051/CDE6552/CDE7051 Interface:

Item Description

LAN IN VGA OUT MIC AUDIO OUT USB IN

TOUCH

HDMI IN COAXIAL VGA IN AUDIO IN YPbPr IN AV IN AV OUT MIC IN

Standard RJ45 (10M/100M/1G) Internet connection interface Connects the display to a VGA-IN connector Connects to a microphone Connects the device to headphones or speakers Connects USB peripherals such as HDDs USB keyboards and

mice Display Motherboard Upgrade Interface Touch signal input, controls an external PC once the driver has

been installed (available through PC, VGA and HDMI sources). High Definition Multimedia Interface Coaxial output Connects the device to external video sources Connects the device to external audio sources YPbPr signal input, connects to DVD players and set-top boxes Audio-Video combined input port Audio-Video output port

Connects to a microphone RS232 AC IN POWER

Note: Model no. CDE6552/CDE7051 does not have interface features #1 – 5 if the optional slot-in PC module is not installed.

Serial port interface

AC power input

Power On / Off switch

SWB8451/CDE8451 Interface:

Item Description

USB interface, connect USB devices such as mobile hard disk, U disk, USB keyboard and mouse, USB drives, etc

High Definition Multimedia Interface, HDMI3 can realize MHL function, HDMI4 can realize 4Kx2K

Connected to display devices with VGA input function Connects the device to external audio sources Connects the device to external video sources Touch signal input, controls an external PC once the driver has been in-

stalled (available through PC, VGA and HDMI sources). Audio-Video combined input port Coaxial output Serial port interface Connects the device to headphones or speakers Standard RJ45 (10M/100M/1G) Internet connection interface (This network

port is only used for Android system) AC power input Power On / Off switch Standard RJ45 (10M/100M/1G) Internet connection interface (This network

port is only used for PC) Connects the device to headphones or speakers Connects to a microphone Connects the display to a VGA-IN connector Connects the display to a DisplayPort connector Connected to device with HDMI input function USB 3.0 interface , connects USB peripherals such as HDDs USB

keyboards and mice USB 2.0 interface , connects USB peripherals such as HDDs USB

keyboards and mice

Note: Model no. CDE8451 does not have interface features #14 – 21 if the optional slot-in PC module is not installed.

2.3 Remote Control Overview

Press to turn the display ON/OFF (Standby), or press and hold for 5 seconds to shut down

Press to scroll down

Mute / Unmute

Set the sleep time function (55", 65", 70")

Display information of the current input source

Picture mode selection (55", 65", 70") Blank screen (84")

Sound mode selection (55", 65", 70")

Numeric input button

Press to switch between PC applications

Numeric input button

Close current PC window

Source selection button

Press to display Menu

Adjust the aspect ratio of PC, HDMI and VGA sources (55", 65", 70")

Enter button. Press it to select options.

Writing software startup

Shortcut button to exit dialog boxes

Digital program guide (not available)

PC ‘Space’ button

CH+ : PC previous page (84") CH- : PC next page (84")

Increase / Decrease volume

F1 Function

F2 Function

F3 Function

4 Function

F5 Function

F6 Function

PC ‘Alt’ button (55", 65", 70")

PC ‘Tab’ button (55", 65", 70")

Switch to Windows Desktop Switch to Android main screen (84")

PC ‘Backspace’ button

PC ‘Windows’ button

PC ‘Menu’ button (55", 65", 70")

Press to scroll up

Press to scroll left

Press to scroll right

F7 Function

F8 Function

F9 Function

F10 Function

F11 Function

F12 Function

2.4 Inserting Remote Control Batteries

To insert the provided batteries into the remote control follow these instructions. We recommend that you don’t mix battery types.

1. Remove the cover on the rear of the remote control.

2. Insert two “AAA” batteries, ensuring the “+” symbol on the battery matches the

“+” on the battery post.

3. Replace the cover by aligning it with the slot on the remote control and snapping

the latch shut.

Warning: There is a risk of explosion if batteries are replaced with the incorrect type.

Note: Always dispose of old batteries in an environmentally friendly way. Contact

your local government for more information on how to dispose of batteries safely.

2.5 Remote Control Receiver Range

The working range of the remote control receiver is shown here. It has an effective range of 8 meters. Make sure there is nothing obstructing the remote control’s signal to the receiver.

3. Setting Up Your Display

Warning: For the safety of you and your unit, please do not connect to a power

supply before the external device is prepared.

3.1 Connecting an External PC

SWB5501/CDE5501 Models:

SWB6552/SWB7051/CDE6552/CDE7051 Models:

SWB8451/CDE8451 Models:

1. To display video and sound from an external PC follow the instructions below. Note: External PCs can also be connected to the display via HDMI cable.

• Connect a VGA cable (15-pin) from your external PC to the VGA IN port on

the display.

• Connect an audio cable from the AUDIO OUT port on your external PC to the

AUDIO IN port on the display.

2. Connect a USB cable to the external PC from the TOUCH OUT port of the display.

3. Plug the power cord into the rear panel of the display and flip the power switch (I/O) to the “I” position. The display is now in “Standby” mode.

4. Turn on your external computer and set up the touch driver.

5. Press the button on the right-hand side of the display to turn on the screen.

6. Press the INPUT button to switch to the “PC” source.

Note: For optimal results, select 1920x1080p as the external computer's input

resolution.

3.2 RS232 Connections

When you use a RS232 serial port cable to connect your display to an external computer, certain functions can be controlled by the PC, including power on/off, volume adjustment and more.

+ 59 hidden pages