ViewSonic SD-Z225 User Guide

SD-Z225 Zero Client Monitor

User Guide

IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http://

www.viewsonic.com in English, or in specic languages using the Regional selection

box in the upper right corner of our website. “Antes de operar su equipo lea cu idadosamente las instrucciones en este manual”

Model No. VS15177

Compliance Information

NOTE: This section addresses all connected requirements and statements regarding

regulations. Confirmed corresponding applications shall refer to nameplate labels and relevant markings on unit.

FCC Compliance Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

Industry Canada Statement

CAN ICES-3(B)/NMB-3(B)

Following information is only for EU-member states:

The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE).The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste, but use the return and collection systems according to local law.

Declaration of RoHS Compliance

This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Lead (Pb) 0,1% < 0,1%

Mercury (Hg) 0,1% < 0,1%

Cadmium (Cd) 0,01% < 0,01%

Hexavalent Chromium (Cr

Polybrominated biphenyls (PBB) 0,1% < 0,1%

Polybrominated diphenyl ethers (PBDE) 0,1% < 0,1%

) 0,1% < 0,1%

Proposed Maximum Concentration

Actual Concentration

Certain components of products as stated above are exempted under the Annex of the RoHS Directives as noted below: Examples of exempted components are:

1. Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in other

lamps not specifically mentioned in the Annex of RoHS Directive.

2. Lead in glass of cathode ray tubes, electronic components, fluorescent tubes,

and electronic ceramic parts (e.g. piezoelectronic devices).

3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by

weight or more lead).

4. Lead as an allotting element in steel containing up to 0.35% lead by weight,

aluminum containing up to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by weight.

Cautions and Warnings

1. Read these instructions completely before using the equipment.

2. Keep these instructions in a safe place.

3. Heed all warnings and follow all instructions.

4. Sit at least 18” / 45cm from the Zero Client Monitor.

5. Always handle the Zero Client Monitor with care when moving it.

6. Never remove the rear cover. This Zero Client Monitor contains high-voltage

parts. You may be seriously injured if you touch them.

7. Do not use this equipment near water. Warning: To reduce the risk of fire or

electric shock, do not expose this apparatus to rain or moisture.

8. Avoid exposing the Zero Client Monitor to direct sunlight or another heat source.

Orient the Zero Client Monitor away from direct sunlight to reduce glare.

9. Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the

Display” in this guide for further instructions.

10. Avoid touching the screen. Skin oils are difficult to remove.

11. Do not rub or apply pressure to the LCD panel, as it may permanently damage

the screen.

12. Do not block any ventilation openings. Install the equipment in accordance with

the manufacturer’s instructions.

13. Do not install near any heat sources such as radiators, heat registers, stoves, or

other devices (including amplifiers) that produce heat.

14. Place the Zero Client Monitor in a well ventilated area. Do not place anything on

the Zero Client Monitor that prevents heat dissipation.

15. Do not place heavy objects on the Zero Client Monitor, video cable, or power

cord.

16. If smoke, an abnormal noise, or a strange odor is present, immediately switch

the Zero Client Monitor off and call your dealer or ViewSonic. It is dangerous to continue using the Zero Client Monitor.

17. Do not attempt to circumvent the safety provisions of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade and the third prong are provided for your safety. If the plug does not fit into your outlet, consult an electrician for replacement of the outlet.

18. Protect the power cord from being tread upon or pinched, particularly at the plug,

and the point where if emerges from the equipment. Be sure that the power outlet is located near the equipment so that it is easily accessible.

19. Only use attachments/accessories specified by the manufacturer.

(Continued on next page)

iii

20. Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the equipment. When a cart is used, use caution when moving the cart/equipment combination to avoid injury from tipping over.

21. Unplug this equipment when it will be unused for long periods of time.

22. Refer all servicing to qualified service personnel. Service is required when the

unit has been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the unit does not operate normally or has been dropped.

Contents

Compliance Information

FCC Compliance Statement ...................................................................................i

Industry Canada Statement ....................................................................................i

Declaration of RoHS Compliance .......................................................................... ii

Cautions and Warnings ........................................................................................ iii

Product Registration ..............................................................................................2

For Your Records ..................................................................................................2

Getting Started

Package Contents .................................................................................................3

Quick Installation ...................................................................................................4

Additional Software Installation (Optional).............................................................4

Wall Mounting (Optional) .......................................................................................5

Using the Zero Client Monitor

Setting the Timing Mode........................................................................................8

OSD and Power Lock Settings ..............................................................................8

Adjusting the Screen Image ..................................................................................9

Main Menu Controls ............................................................................................10

Main Menu Explanation .......................................................................................10

Other Information

Specifications ......................................................................................................12

Cleaning the Zero Client Monitor .........................................................................14

Troubleshooting ...................................................................................................15

Customer Support ...............................................................................................16

Limited Warranty ................................................................................................17

Copyright © ViewSonic® Corporation, 2013. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association. DPMS, DisplayPort, and DDC are trademarks of VESA. Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product. In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change product specifications without notice. Information in this document may change without notice. No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To fulfill possible future product needs, and to receive additional product information as it becomes available, please visit your region section on ViewSonic’s website to register your product online.

For Your Records

Product Name:

Model Number: Document Number: Serial Number: Purchase Date:

Product disposal at end of product life

ViewSonic respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic website to learn more. USA & Canada: http://www.viewsonic.com/company/green/recycle-program/ Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/ Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

SD-Z225 ViewSonic Zero Client Monitor VS15177 SD-Z225_UG_ENG Rev. 1A 12-18-12

+ 17 hidden pages