ViewSonic SC-Z55 Zero Client User Manual

Download

SC-Z55 Zero Client

User Guide

Model No. VS15168

Compliance Information

FCC Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help. Warning: You are cautioned that changes or modications not expressly approved by the

party responsible for compliance could void your authority to operate the equipment.

For Canada

• This Class B digital apparatus complies with Canadian CAN ICES-3 (B).

• Cet appareil numérique de la classe B est conforme à la norme NMB-3 (B) du Canada.

Following information is only for EU-member states:

The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE).

The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries or accumulators as unsorted municipal waste, but use the return and collection systems available. If the batteries, accumulators and button cells included with this equipment, display the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of more than 0.0005% Mercury or more than, 0.002% Cadmium, or more than 0.004% Lead.

Important Safety Instructions

1. Read these instructions completely before using the equipment.

2. Keep these instructions in a safe place.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this equipment near water. Warning: To reduce the risk of re or electric

shock, do not expose this apparatus to rain or moisture.

6. Do not block any ventilation openings. Install the equipment in accordance with the manufacturer’s instructions.

7. Do not install near any heat sources such as radiators, heat registers, stoves, or other

devices (including ampliers) that produce heat.

8. Do not attempt to circumvent the safety provisions of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding

type plug has two blades and a third grounding prong. The wide blade and the third

prong are provided for your safety. If the plug does not t into your outlet, consult an

electrician for replacement of the outlet.

9. Protect the power cord from being tread upon or pinched, particularly at the plug, and the point where if emerges from the equipment. Be sure that the power outlet is located near the equipment so that it is easily accessible.

10. Only use attachments/accessories specied by the manufacturer.

11. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the equipment. When a cart is used, use caution

when moving the cart/equipment combination to avoid injury from tipping over.

12. Unplug this equipment when it will be unused for long periods of time.

13. Refer all servicing to qualied service personnel. Service is required when the unit has been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or

moisture, or if the unit does not operate normally or has been dropped.

14. Do not remove equipment covers and access any of the components inside the

equipment. Any access inside the equipment without an authorized or certied

technician may cause serious injuries and damage. For any problem, contact your dealer for assistance.

15. Don’t use a keyboard and mouse that in total require more than 200 mA of rated current during operation.

16. Use only power supplies listed in the user instructions.

iii

Declaration of RoHS Compliance

This product has been designed and manufactured in compliance with Directive 2002/95/ EC of the European Parliament and the Council on restriction of the use of certain

hazardous substances in electrical and electronic equipment (RoHS Directive) and is

deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Proposed Maximum

Concentration

Actual Concentration

Lead (Pb) 0.1% < 0.1%

Mercury (Hg) 0.1% < 0.1%

Cadmium (Cd) 0.01% < 0.01%

Hexavalent Chromium (Cr6+) 0.1% < 0.1%

Polybrominated biphenyls (PBB) 0.1% < 0.1%

Polybrominated diphenyl ethers

(PBDE)

0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex of the

RoHS Directives as noted below:

Examples of exempted components are:

1. Mercury in compact uorescent lamps not exceeding 5 mg per lamp and in other lamps

not specically mentioned in the Annex of RoHS Directive.

2. Lead in glass of cathode ray tubes, electronic components, uorescent tubes, and

electronic ceramic parts (e.g. piezoelectronic devices).

3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight

or more lead).

4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium

containing up to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by weight.

ViewSonic, the three birds logo, OnView, ViewMatch, ViewMeter, and MultiClient are either registered trademarks or trademarks of ViewSonic Corporation.

Microsoft

, Windows®, and MultiPoint™ are trademarks of the Microsoft group of

companies.

ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR® partner, ViewSonic Corporation has determined that this product meets the ENERGY STAR® guidelines for energy

efciency.

Other product names mentioned herein are used for identication purposes only and may

be trademarks and/or registered trademarks of their respective companies.

Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves the

right to change product specications without notice. Information in this document may

change without notice.

No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic Corporation.

NOTE

• Display Sleep Mode. Within 5 minutes of user inactivity, the display will enter

the Display Sleep mode with a blank screen and reduced power consumption by the factory default settings. The display returns to the Display Normal mode upon sensing a request from a user such as moving the mouse or pressing a key.

• To adjust settings for the Display Sleep mode, click Options > Conguration > OSD to adjust the settings.

• System Sleep Mode. ViewSonic SC-Z55 doesn’t support the System/Client Sleep mode.

NOTE

• The default power management settings have been selected for compliance with ENERGY STAR that are recommended by the ENERGY STAR program for optimal energy savings.

Product Registration

To meet your future needs, and to receive any additional product information as it becomes available, please register your product on the Internet at: www.viewsonic.com.

For Your Records

Product Name:

Model Number: Document Number: Serial Number: Purchase Date:

SC-Z55 ViewSonic Zero Client VS15168 SC-Z55_UG_ENG Rev. 1A 01-02-13

_______________________________ _______________________________

Product disposal at end of product life

ViewSonic respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic website to learn more.

USA & Canada: http://www.viewsonic.com/company/green/recycle-program/

Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/

Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

About This User’s Manual

This installation guide provides basic information on how to set up SC-Z55 zero clients.

Manual Structure and Subjects

Chapter Subject

1 Provides an overview of ViewSonic SC-Z55 zero clients.

2 Provides detailed instructions on how to set up ViewSonic SC-Z55 zero clients.

Specications Provides detailed information on key components of ViewSonic SC-Z55 zero clients.

Notes, Tips, and Warnings

Throughout this manual, the notes and warnings in the following formats are used to provide important information, and prevent injuries to you, damage to your devices, or loss of data on your system.

NOTE

• Anoteprovidesimportantinformationforaspecicsituation.

WARNING

• A warning provides crucial information that must be followed to prevent injuries to you, damage to your devices, or loss of data on your system.

Table of Contents

Compliance Information i

Important Safety Instructions ii

Declaration of RoHS Compliance iii

Product Registration v

About This User’s Manual vi

Manual Structure and Subjects vi Notes, Tips, and Warnings vi

1 Overview 1

1.1 Introduction 2

1.2 Features 2

1.3 Package Contents 3

1.4 Exterior Views 3

1.5 Panel Components 4

1.6 LED Indicators 6

2 Setting Up Your SC-Z55 7

2.1 Positioning Your SC-Z55 8

2.2 Assembling the AC Adapter 11

2.3 Getting Connected 12

Specications 13

Other Information 14

Customer Support 14

Limited Warranty 15

Overview

This chapter provides an overview of your SC-Z55 zero clients.

1.1 Introduction

Desktop virtualization and simple endpoint devices 2

1.2 Features

Key features of ViewSonic SC-Z55 2

1.3 Package Contents

Check your package contents 3

1.4 Exterior Views

Overview of zero client outside elements 3

1.5 Panel Components

Descriptions of front and rear panel components 4

1.6 LED Indicators

Descriptions of signals for LED indicators 6

Overview

Introduction

1.1 Introduction

Desktop virtualization provides a new perspective to reconsider the design and implementation of an IT infrastructure. In a desktop virtualization infrastructure, a station is no longer a cumbersome desktop, but simply an endpoint device for users to access delivery services from the server(s).

With the introduction of the desktop virtualization technologies, you can considerably benet from:

• On-demand applications/desktops

• Centralized management of work environments

• Drastically reduced endpoint software/hardware issues

• Simplied system maintenance and Improved system security

• More scalability with low-cost endpoint devices

1.2 Features

The key features of ViewSonic SC-Z55 zero clients are:

• Teradici™ TERA2321 processor with Teradici™ 2nd generation zero client chipset

• Support for VMware® desktop virtualization solution: VMware® View™

Overview

Package Contents

1.3 Package Contents

Please check your package contents. Ensure that all of the items are present in your package. If any items are missing or damaged, please contact your dealer immediately.

ViewSonic SC-Z55

ViewSonic SC-Z55 AC adapter DVI-I to VGA adapter

Stand (VESA plate) Driver CD Quick Start Guide

SC-Z55

01/02/13SC-Z55_CD

Zero Client

Compliance Information

brochure

1.4 Exterior Views

ViewSonic SC-Z55

Rear PanelFront Panel

Left Front View Right Rear View

Overview

Panel Components

1.5 Panel Components

ViewSonic SC-Z55

Front Panel

No. Component Sign Name Description

Power LED Indicates the status of power.

Power button

• Press to power on the zero client.

• Long press to force power off the zero client.

Microphone port Connects to a microphone.

Headphone port

Connects to a set of headphones or a speaker system.

USB port Connects to a USB device.

Overview

Panel Components

ViewSonic SC-Z55

Rear Panel

No. Panel Component Sign Component Name Description

DVI-D port

Connects to a high quality digital display device such as a LCD monitor or a digital projector.

DVI-I port

Connects to a high quality digital display device such as a LCD monitor or a digital projector.

LAN port Connects to a network.

USB port Connects to a keyboard or mouse.

DC IN Connects to an AC adapter.

NOTE

• Your SC-Z55 comes with a DVI-I to VGA adapter. If only the VGA monitor is available, use the supplied DVI-I to VGA adapter to connect your VGA monitor to SC-Z55’s DVI-I port. For detailed instructions, please see section ”2.3 Getting Connected” on page 12.

Overview

LED Indicators

1.6 LED Indicators

Your SC-Z55 is equipped with a Power LED to indicate the state of power. The meanings of LED signals are described as follows:

LED Signal Meaning

Power LED

Off The client is off.

Blue The client is on.

The LAN port of your SC-Z55 has two LED indicators showing the state of networking. The meanings of LED signals are described as follows:

Left LED

(transmission rate)

Right LED

(transmission activity)

Meaning

LED Signal

Off Off The client is not connected to a LAN.

Off Amber blinking The client connects to a 10 Mbps LAN.

Orange Amber blinking The client connects to a 100 Mbps LAN.

Green Amber blinking The client connects to a 1000 Mbps LAN.

Setting Up Your SC-Z55

This chapter provides detailed instructions on how to set up your SC-Z55 zero clients.

2.1 Positioning Your SC-Z55

To mount your SC-Z55

Step 1: Remove the Stand from Your SC-Z55 Step 2: Understand Your Stand / VESA Mount Kit for SC-Z55 Step 3: Store Screws inside the Bracket Step 4: Remove Screws from the Bracket Step 5: Mount Your SC-Z55

9 10 10 11

2.2 Assembling the AC Adapter

How to assemble the AC adapter and its detached plug 11

2.3 Getting Connected

How to connect peripherals and power for SC-Z55 12

Setting Up Your SC-Z55

Positioning Your SC-Z55

2.1 Positioning Your SC-Z55

There are two ways to position your SC-Z55:

• Put it (with its stand) on a desk or a desired place uprightly.

• Mount it on the back of a monitor using a VESA mount kit.

To mount your SC-Z55 on the back of a monitor, please follow the steps below:

Step 1: Remove the Stand from Your SC-Z55

Step 2: Understand Your Stand / VESA Mount Kit for SC-Z55

Step 3: Store Away Screws inside the Bracket

Step 4: Remove Screws from the Bracket

Step 5: Mount Your SC-Z55

Step 1: Remove the Stand from Your SC-Z55

To remove the stand from your SC-Z55, please do the following:

1. Place your SC-Z55 on a at surface with the stand side upward.

2. Remove the screw that xes the stand to your SC-Z55.

3. Store away the removed screw inside the stand. Detailed instructions will be provided in Step 2 and 3.

NOTE

• It’s highly recommended to store screws away inside the stand when not needed to prevent them getting lost.

台灣製造 / 台湾制造 / Made in Taiwan

JPAA

Input/輸入 / 输入

+5V 3A

Setting Up Your SC-Z55

Positioning Your SC-Z55

Step 2: Understand Your Stand / VESA Mount Kit for SC-Z55

The stand for your SC-Z55 is dual-purpose: it can be used as a stand or as a VESA mount kit. All screws of dierent types supplied with the stand / VESA mount kit can be stored away inside the main bracket when not needed.

Screws Stored Away inside the Bracket

The following gure shows dierent types of screws stored away inside the main bracket.

Screw Type Number Description

1 2

The largest-size screws used to secure the bracket to a monitor as a VESA mount

ifthemiddle-sizescrewscannotrmlysecurethebracketandyourSC-Z55tothe

monitor.

2 4

The middle-size screws used to secure the bracket to your SC-Z55 and to a monitor when using the bracket as a VESA mount.

3 1 The smallest-size screw used to secure the bracket to your SC-Z55 as a stand.

Mount Holes on the Bracket

Refer to the following gure and descriptions for the VESA mount holes on the bracket.

Mount Hole Description

1 The VESA mount holes used to secure the bracket to a monitor (only two of them will be used).

The VESA mount holes used to secure the bracket to your SC-Z55 (only two of them will be used).

Dual-purpose

bracket

Setting Up Your SC-Z55

Positioning Your SC-Z55

Step 3: Store Screws inside the Bracket

To store screws inside the bracket, please do the following:

NOTE

• It’s highly recommended to store screws inside the bracket when not needed to prevent them getting lost.

1. Place a sheet of paper or a piece of cloth on a at surface, and then put your bracket on that paper or cloth with the screw storage side upward.

2. Place the screw upon its storage space, and push the screw into the space with your nger until it clicks into place. For the smallest-size screw, use the tip of a screwdriver instead to push the screw.

NOTE

• Please refer to the gure and descriptions in “Step 2: Understand Your Stand / VESA Mount Kit for SC-Z55”5” for the correct storage space of each screw.

Step 4: Remove Screws from the Bracket

To remove screws stored inside the bracket, please do the following:

1. Place a sheet of paper or a piece of cloth on a at surface, and then put your bracket on that paper or cloth with the screw storage side downward.

2. Insert the tip of a screwdriver into the square holes to remove the desired screws from the bracket.

Square Hole

Setting Up Your SC-Z55

Assembling the AC Adapter

Step 5: Mount Your SC-Z55

To mount your SC-Z55 on the back of a monitor, please do the following:

1. Refer to Step 2 and Step 4 to prepare required screws for mounting your SC-Z55.

• You will need two (2) screws of type

to secure the bracket to your SC-Z55.

• You will need two (2) screws of type

or 2 to secure the bracket to the monitor.

2. Place your SC-Z55 on a at surface with the VESA mount hole side upward.

3. Refer to Step 2 to choose two of the four VESA mount holes on the bracket to align with two mount holes on your SC-Z55 such that the bracket projects out and is closer to the rear panel than the front one as shown

below, and then secure the bracket to your SC-Z55 with two (2) screws of type

4. Align the mount holes on the bracket with the mount holes on the back of the monitor, and then secure the bracket to the monitor with two (2) screws of type

or 1. Ensure that your SC-Z55 is located in the center

of the monitor and the rear panel of your SC-Z55 is facing rightward as shown below.

2.2 Assembling the AC Adapter

To assemble the AC adapter for your SC-Z55, please do the following:

1. Unpack your zero client package and take out the AC adapter and its detached plug.

2. Slide the plug into the AC adapter until it clicks into place.

NOTE

• The supplied plug may vary, depending on dierent areas.

Have SC-Z55’s rear panel facing rightward.

Setting Up Your SC-Z55

Getting Connected

2.3 Getting Connected

To make connections for your SC-Z55, please do the following:

1. Connect your SC-Z55 to your local network with an Ethernet cable.

2. Connect a keyboard and mouse to your SC-Z55.

3. Connect and turn on the monitor(s).

NOTE

• For your SC-Z55, if only the VGA monitor is available, use the supplied DVI-I to VGA adapter to connect your SC-Z55 and monitor.

• Please note that you need to connect and turn on your monitor(s) before powering up your zero client. Otherwise, the client may fail to set an appropriate resolution for the monitor(s).

4. Connect your SC-Z55 to a power outlet using the AC adapter included in the package.

NOTE

• For detailed instructions on how to assemble the supplied AC adapter, please refer to section ”2.2 Assembling the AC Adapter” on page 11.

5. Connect other peripherals for your SC-Z55 if needed.

Manual of Zero Client, PCoIP rmware update and PCoIP Management Console Software:

1. Please visit ViewSonic website at www.viewsonic.com to download the user guide of Zero Client and PCoIP rmware updates.

2. The latest version of “PCoIP Management Console Software” can be downloaded free of charge from the Teradici web site. You will simply need to create an account rst and accept the End User License Agreement (EULA), before downloading: http://techsupport.teradici.com/ics/support/default.asp?deptID=15164

DVI-I port

(SC-Z55 only)

DVI-I to VGA

adapter

VGA cable

Specications

ViewSonic SC-Z55 zero client

Processor

Teradici TERA2321

Memory

512 MB

Resolutions

Two DVI ports for one display: Up to 2560 x 1600, dual DVI-to-DVI Y cable needed (optional) One DVI port for one display: Up to 1920 x 1200

I/O interfaces

Front: 2 x USB 2.0 1 x Microphone

1 x Headphone

Rear: 2 x USB 2.0 1 x RJ-45

1 x DVI-I 1 x DVI-D

1 x DC IN

Networking

1 x 10/100/1000Mb Ethernet

Power

DC Power In: DC 5V, 3A External Power Adapter: AC 100-240, 50/60Hz, 0.5A

Supported Protocols

VMware PCoIP

Security

1 x Kensington lock slot

Mount / Stand

VESA mount kit / Stand, (W)68 x (H)10 x (D)111 mm

Dimensions

(W)39.5 x (H)143 x (D)103 mm

Net Weight

1.15 lbs (0.52 kgs)

Environment

Operating Temperature: 0° C ~ 40° C Non-operating Temperature: -30° C ~ 60° C Operating Humidity (Rh): 10% ~ 90% (non-condensing) Non-operating Humidity (Rh): 5% ~ 95%

Other Information

Customer Support

For technical support or product service, see the table below or contact your reseller.

NOTE: You will need the product serial number.

Country/ Region

Website

T = Telephone F = FAX

Australia/New Zealand

www.viewsonic.com.au

AUS= 1800 880 818 NZ= 0800 008 822

service@au.viewsonic.com

Canada www.viewsonic.com

T (Toll-Free)= 1-866-463-4775 T (Toll)= 1-424-233-2533 F= 1-909-468-3757

service.ca@viewsonic.com

Europe www.viewsoniceurope.com www.viewsoniceurope.com/uk/support/call-desk/

Hong Kong www.hk.viewsonic.com T= 852 3102 2900 service@hk.viewsonic.com

India www.in.viewsonic.com T= 1800 266 0101 service@in.viewsonic.com

Korea www.kr.viewsonic.com T= 080 333 2131 service@kr.viewsonic.com

Latin America (Argentina)

www.viewsonic.com/la/ T= 0800-4441185 soporte@viewsonic.com

Latin America

(Chile)

www.viewsonic.com/la/ T= 1230-020-7975 soporte@viewsonic.com

Latin America

(Columbia)

www.viewsonic.com/la/ T= 01800-9-157235 soporte@viewsonic.com

Latin America (Mexico)

www.viewsonic.com/la/ T= 001-8882328722 soporte@viewsonic.com

Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS Electroser, Av Reforma No. 403Gx39 y 41, 97000 Mérida, Yucatán. Tel: 01.999.925.19.16 Other places please refer to http://www.viewsonic.com/la/soporte/index.htm#Mexico

Latin America

(Peru)

www.viewsonic.com/la/ T= 0800-54565 soporte@viewsonic.com

Macau www.hk.viewsonic.com T= 853 2870 0303 service@hk.viewsonic.com

Middle East ap.viewsonic.com/me/ Contact your reseller service@ap.viewsonic.com

Puerto Rico &

Virgin Islands

www.viewsonic.com

T= 1-800-688-6688 (English) T= 1-866-379-1304 (Spanish) F= 1-909-468-3757

service.us@viewsonic.com soporte@viewsonic.com

Singapore/ Malaysia/

Thailand

www.ap.viewsonic.com T= 65 6461 6044 service@sg.viewsonic.com

South Africa ap.viewsonic.com/za/ Contact your reseller service@ap.viewsonic.com

United States www.viewsonic.com

T (Toll-Free)= 1-800-688-6688 T (Toll)= 1-424-233-2530 F= 1-909-468-3757

service.us@viewsonic.com

Limited Warranty

ViewSonic® Thin Client

What the warranty covers:

ViewSonic warrants its products to be free from defects in material and workmanship during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a similar product. Replacement Product or parts may include remanufactured or refurbished parts or components. The replacement unit will be covered by the balance of the time remaining on the customer’s original limited warranty. ViewSonic provides no warranty

for the third-party software included with the product or installed by the customer.

How long the warranty is effective:

ViewSonic Thin Client products are warranted for (3) years from the rst consumer purchase for parts and

labor. User is responsible for the back up of any data before returning the unit for service. ViewSonic is not

responsible for any data lost.

Who the warranty protects:

This warranty is valid only for the rst consumer purchaser.

What the warranty does not cover:

1. Any product on which the serial number has been defaced, modied or removed.

2. Damage, deterioration or malfunction resulting from:

a. Accident, misuse, neglect, re, water, lightning, or other acts of nature, unauthorized product

modication, or failure to follow instructions supplied with the product.

b. Any damage of the product due to shipment.

c. Removal or installation of the product.

d. Causes external to the product, such as electrical power uctuations or failure. e. Use of supplies or parts not meeting ViewSonic’s specications.

f. Normal wear and tear.

g. Any other cause which does not relate to a product defect.

3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is displayed on the product for an extended period of time.

4. Removal, installation, one way transportation, insurance, and set-up service charges.

How to get service:

1. For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to Customer Support page). You will need to provide your product’s serial number.

2. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.

3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center

or ViewSonic.

4. For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description contained herein including the implied warranty of merchantability and tness for a particular purpose.

4.3: ViewSonic Thin Client Warranty Page 1 of 2 MC_LW01 Rev. 1a 09-02-11

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:

1. Damage to other property caused by any defects in the product, damages based upon inconvenience,

loss of use of the product, loss of time, loss of prots, loss of business opportunity, loss of goodwill,

interference with business relationships, or other commercial loss, even if advised of the possibility of such damages.

2. Any other damages, whether incidental, consequential or otherwise.

3. Any claim against the customer by any other party.

4. Repair or attempted repair by anyone not authorized by ViewSonic.

Effect of state law:

This warranty gives you specic legal rights, and you may also have other rights which vary from state to state. Some states do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the above limitations and exclusions may not apply to you.

Sales outside the U.S.A. and Canada:

For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada, contact

ViewSonic or your local ViewSonic dealer.

The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan Excluded) is subject to the terms and conditions of the Maintenance Guarantee Card.

For users in Europe and Russia, full details of warranty provided can be found in www.viewsoniceurope.com under Support/Warranty Information.

4.3: ViewSonic Thin Client Warranty Page 2 of 2 MC_LW01 Rev. 1a 09-02-11

ViewSonic SC-Z55 Zero Client User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual