LITEBIRD
User Guide
Guide de l’utilisateur
Bedienungsanleitung
(International Spanish)
(Italian)
(Brazilian Portuguese)
(Swedish)
(Russian)
(Polish)
(Japanese)
(Traditional Chinese)
TM
Image Size 30” – 300”
Super Bright SVGA LCD Projector
(Simplified Chinese)
(Korean)
(Arabic)
Contents
For Your Records ............................................................................1
Getting Started
Package Contents ...........................................................................2
Important Safety Warnings ..............................................................2
Connect Input and Output Devices..................................................3
Installation Steps .............................................................................4
Adjusting the Projector Angle ....................................................5
Projector Placement Distance ...................................................5
Using The Projector
Control Buttons................................................................................6
OnView Indicators............................................................................8
Setup Main Menu .....................................................................8
Input Menu ...............................................................................9
Image Menu .............................................................................9
Options Menu .........................................................................10
Other Information
Specifications ................................................................................11
Timing Chart ............................................................................12
Troubleshooting.............................................................................13
Power Indicator Lights .............................................................14
Screen Messages ....................................................................14
Maintenance ..................................................................................15
Lamp Replacement .............................................................15
Installing Battery (for remote control) ......................................16
Cleaning Instructions ...............................................................16
Air-Filter ...................................................................................17
Customer Support..........................................................................18
E
N
G
L
I
S
H
LIMITED WARRANTY
VIEWSONIC Projector ............................................................19
Appendix
Power Cord Safety Guidelines.......................................................20
FCC Information ............................................................................21
ViewSonic PJ853 i
Copyright © ViewSonic Corporation, 2000. All right reserved.
Macintosh, Mac and Power Macintosh are registered trademarks of Apple Computer, Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
E
N
G
L
I
S
H
ViewSonic, the three birds logo and OnView are registered trademarks of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC
are trademarks of VESA.
E
NERGY STAR
®
is a registered trademark of the U.S. Environmental Protection Agency (EPA).
As an ENERGY STAR®partner, ViewSonic Corporation has determined that this product meets the
NERGY STAR
E
®
guidelines for energy efficiency.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions
contained herein; norfor incidental orconsequential damagesresultingfrom furnishing thismaterial,
or the performance or use this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to
change product specifications without notice. Information in this document may change without
notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose
without prior written permission from ViewSonic Corporation.
Electronic Warranty Registration
To meet your future needs, and to receive any additional product
information as it becomes available, please register your projector's
warranty on the Internet at:
http://www.viewsonic.com
For Your Records
Product Name:
Model Number:
Document Number
Serial Number:
Purchase Date:
ViewSonic PJ853
VPROJ21732
PJ853_UG_59
_______________
_______________
1 ViewSonic PJ853
Getting Started
Congratulations on purchasing a ViewSonic PJ853 LITEBIRD™ LCD projector. Save the original
box and all packing material for future shipping needs.
Package Contents
• ViewSonic PJ853 LITEBIRD LCD Projector
• Remote Control Unit including 3V micro-lithium battery
• Three (3) AC power cords (U.S., European and China)
• Computer video cable (15-pin mini D-sub connector)
• Video cable (RCA connectors)
• Audio mini-stereo cable (RCA connectors)
• User guide
• Carrying Case
PJ853
Power Cord
US Type
E
N
G
L
I
S
H
Power Cord
Europe Type
RGB Cable
Figure 1: Package Contents
Important SafetyWarnings
• Unplug the projector immediately if you detect an abnormal smell or see smoke.
• Do not look directly into the lighted lens; doing so will cause severe eye injury.
• Keep small children away from the projector. Children can be severely burned by thehot lens.
Also, children are more likely to look directly into thelens.
• Nevertouch thelens or the lampwhen hot orwarm; doing sowill causea severe burn. Unplug the
projector and allow the unit to cool down for 45 minutes before replacing the lamp or storing the
projector.
• Do not service the unit yourself; doing so could cause injury.
• Do not operate the projector near water or in a humid area. Do not sit drinks on or near the
projector; doing so could cause a burn or short an electrical circuit.
• Do notblock theventilationopenings inthe projector.Place theprojector so that thereis adequate
air circulation
• Keep the air filter clean.
• Do not place the projector on a shelf or on any other unstable surface.
ViewSonic PJ853 2
S
T
A
N
D
B
Y
/
O
N
I
N
P
U
T
M
U
T
E
R
E
S
E
T
M
E
N
U
P
O
W
E
R
T
E
M
P
L
A
M
P
Projector control
panel
E
Powe r Sw itc h
Remote Control Sensor
N
G
L
I
(to the power cord)
AC Inlet
Lens
S
H
Air Vent
(Intake)
Foot Adjuster
Figure 2: ViewSonic PJ853 Projector
Connect Input and Output Devices
The figure below shows the ports and configurations for connecting external devices to the
ViewSonic PJ853. See “Installation Steps” on page 4.
Reset Lamp indicator
Standby/ON
Input
Mute
PJ853
V
ie
w
S
on
ic
Temperature indicator
Power indicator
Menu button
Speaker
S-video IN port
RGB IN port
Control port
Air vent
(exhaust)
Power Outlet
Powe r
ON/OFF
Remote control sensor
Power Cord
Video IN port Audio IN port
Figure 3: Connections and Projector Control Buttons
S
T
A
N
D
B
Y
/
O
N
I
N
P
U
T
M
U
T
E
R
E
S
E
T
M
E
N
U
P
O
W
E
R
T
E
M
P
L
A
M
P
3 ViewSonic PJ853
Installation Steps
1
Verify Input/Output Connections
Make sure that you have properly connected all input cables before powering on the projector.
2
Remove the lens cap.
3
Power on the Projector.
•
Turn onthe Main Power Switch located on the side of the projector. The power indicator will
remain a steady orange. See“Using The Projector” on page6.
4
Press (and hold for 1 second) the Standby/ON button on the projector control pad.
•
The power indicator flashes green during warm-up.
•
The power indicatorwill remain asteady green afterwarm-up. Thesteadygreenlightindicates
that the ViewSonic PJ853 is ready to use.
•
To shut off the lamp – Press the Standby/ON button (and hold for about 3 seconds). The unit
will remain in cool-down mode with the fan on and the orange power LED blinking for 1
minute. The power switch on the side of the projector may be turned off after 1 minute, when
the power light is a steady orange.
5
Position the Projector
Make sure that the projector is properly positioned on a level and stable surface. Determine the
distance the projector willbe from the screen then adjustthe angle of the projection by
positioning the foot adjusters. (See "Adjusting the Projector Angle on page" 5.)
6
Power on Input Devices
•
Press either the Input button on the projector control pad or the Video/RGB button on the
remote control to select the signal to be projected.
•
The selected input signal source displays in the lower right section of the screen.
7
Adjust the Focus
Turn the lens ring to adjust the focus
Caution: The projector requires a warm-up period after the power is turned on, and the projector
requires a cool-down period after the power is turned off.
E
N
G
L
I
S
H
NOTE:
The power cannot be turned on for at least 1 minute after the unit has been powered off; this
is a safety feature.
ViewSonic
P
J853
Notebook Computer
Figure 4: System Setup
Video recorder with S jack
(Note: S-video cable not included)
Video recorderDesktop Computer
ViewSonic PJ853 4
Adjusting the Projector Angle
Adjust the projection angle using the foot adjusters shown in the illustration. See also KEYSTONE
under "Input Menu on page" 9.
1
Press the release button to lower the front foot, then tiltthe projector up as shown in Figure 5
below.
E
N
G
L
I
S
H
•
The front foot locks into place when you release the button.
•
The front foot adjusts the vertical height of the projected image.
2
Rotate the rear foot adjuster to align the image.
The rear foot adjusts the horizontal alignment of the projected image.
Front foot adjuster
Press the release button
to lower the front foot adjuster
Figure 5: Level Adjustments
Rotate the rear
foot adjuster
Projector Placement Distance
Place the projector on a level table-top or other flat surface. Use the chart in Table 1 below to
determine the optimal placement distance from the screen.
b
a
Top View
Figure 6: Recommended Projector Distances
a
Side View
Screen Size
(Inches)
5 ViewSonic PJ853
Tabl e 1: Distance in Inches
a (Inches)
Minimum and Maximum
40 37 46 3
60 57 69 5
80 77 93 7
100 96 116 9
120 116 139 10
150 145 174 13
200 194 233 17
b (Inches)
Using The Projector
The controlbuttons display menusthat are explainedin detailin the section:“OnViewIndicators” on
page 8.
Projector control pad
E
N
G
L
I
S
H
Remote control
Figure 7: Projector and Remote Controls
Control Buttons
Press a control button to displaya menu then use the arrowbuttonsto adjustthe control. Thebuttons
on the projector control pad and on the remote control are explained below:
Standby/on Button
Press the STANDBY/ON button to begin the warm-up period. The ON indicator
blinks green during warm-up and stays green when the projector is ready to use.
NOTE:
the projector enters a cool-down mode. This is a safety feature.
Input Button (Video and RGB Buttons)
The INPUT button shown is on the projector only. Use the Video and RGB buttons on
the remote control to select the input source.
The projectorcannot berestarted within 60seconds afterit is turned off because
Press the Input button on the projector to toggle between input sources, computer
(RGB), Composite or S-Video. The remote control has both a Video and an RGB
button.
-
Press RGB to select a computer as the input source.
-
Press Video to toggle between Composite and S-Video.
ViewSonic PJ853 6
Loading...