Vestil PRCT User Manual

Vestil Manufacturing Corporation

2999 North Wayne St., Angola, IN 46703

Phone [phone] • Fax [phone]

E-mail: [e-mail] • www.vestil.com

Ergonomic Solutions

Contents

Safety Precautions ........................................ 1

Receiving Instructions ...................................1

Warranty ........................................................1

Revised 09-05 33-126-120

A company dedicated to solving ergonomic and material
handling problems since 1955.

OWNER'S
MANUAL

PANEL CART • model PRCT
HEAVY DUTY PANEL CART • model PRCT-HD

Assembly Instructions ................................... 2

Assembly & Parts Drawing ...................... 3 & 4

Warning Label Identification ....................3 & 4

SAFETY PRECAUTIONS

Read owner's manual completely before operating unit!

• Never exceed the maximum capacity of 2,000 pounds.

• Load must be evenly distributed on platform to insure
stability.

• Always apply wheel brakes when unit is not being moved.

• Always operate unit on a level surface to insure stability.

• Use caution in moving a loaded unit; avoid obstructions
and floor defects.

• Make sure all operator safety labels are in place (p.2).

RECEIVING INSTRUCTIONS

Every unit is thoroughly tested and inspected prior to
shipment. However, it is possible that the unit may incur
damage during transit. If damage is noticed when unloading,
make a note of it on the BILL OF LADING. Remove all
packing and strapping material, then inspect the unit again for
damage. IF DAMAGE IS EVIDENT, FILE A CLAIM WITH
THE CARRIER IMMEDIATELY!

WARRANTY

This product is warranted for 90 DAYS from date of
purchase to be free of manufacturing defects in material and
workmanship. The manufacturer's obligation hereunder is
limited to repairing such products during the warranty period,
provided the product is sent prepaid back to the factory.

This warranty does not cover normal wear of parts or
damage resulting from any of the following: negligent use or
misuse of the product, use or application contrary to instal­lation instructions, or disassembly, repair or alteration by any
person prior to authorization from a factory representative.

PANEL CART
MODEL PRCT

HEAVY DUTY
PANEL CART
MODEL PRCT

E
N
G
L

I
S
H

E
S
P
A
N
O
L

F
R
A
N
Ç
A

I
S

1

PANEL CART • MODEL PRCT

Assembly Instructions

1.) Remove top basket retainer from base of panel cart. Slide down on the four upright posts in the center
section of the cart base. (Loosen nuts and bolts on basket assembly if necessary for adjustment to fit.)

2.) For the caster assembly instruction:

Two rigid casters are to be installed on one end of the panel car's base, and the two swivel casters on the
opposite end.

Tip the panel cart onto its side. A caster pad bracket is located at each corner on the bottom of the frame. To
mount a caster, place the caster's mounting plate onto the appropriate caster pad bracket.

Insert a 3/8" diameter x 5" long clevis pin through the square holes in the caster pad bracket. Insert a cotter pin
through the hole in the end of the clevis pin and bend the end of one leg of the cotter pin to secure it.

Return the panel cart to its upright position.

3.) Return to upright position and lock swivel casters.

4.) Place black roller between brackets and insert 1/2" dia. roller pin provided through brackets and roller, leaving
an equal length on each end. Tap on locking end caps to both ends of rod. Unlock wheel.

Refer to tpage 3 for the assembly drawing.

HEAVY DUTY PANEL CART • MODEL PRCT-HD

Assembly Instructions

INSTALL CASTERS

Two rigid casters are to be installed on one end of base frame and two swivel casters at the other end.
The swivel casters should be installed on the same end of the base as the roller brackets.

Tip the panel cart onto its side. A caster pad bracket is located at each corner on the bottom of the frame. To
mount a caster, place the caster's mounting plate onto the appropriate caster pad bracket.

Insert a 3/8" diameter x 5" long clevis pin through the square holes in the caster pad bracket. Insert a cotter pin
through the hole in the end of the clevis pin and bend the end of one leg of the cotter pin to secure it.

Return the panel cart to its upright position.

INSTALL HANDLES:

Three handles are installed on top of base frame.

Return base frame to upright position and lock swivel wheels.

Attach handles to top of platform in pre-drilled holes.

Use 3/8" - 16 UNC x 1-1/4" bolts, flat washers, and 3/8" - 16 UNC lock nuts provided and tightened securely.

Unlock wheels.

Refer to page 4 for assembly drawing.

2