Verizon Telephone Quick Start Manual

© 2006 Verizon

Verizon One

TM

Quick Start Guide

© 2006 Verizon

Verizon One Quick Start Guide

2

1

2

4

5

6

7

8

10

3

1. Verizon One Base Unit with Display

2. Verizon One Base Unit Swivel Support Stand

3. Cordless Telephone Handset with Battery

4. Handset Belt Clip

5. Stylus

6. Power Adaptor and Cord

7. RJ-11 Gray Phone Cord

8. RJ-45 Yellow Ethernet Cable

9. DSL Installation CD

Verizon One will instruct you when to insert into your computer.

10. DSL Filter Kit

The DSL Installation CD will instruct you on where and how to install filters.

Filter Kit only included for new DSL subscribers.

11. Verizon One Important Product Information (not pictured)

12. Verizon Online DSL Resource Guide (not pictured)

9

Thank you for choosing Verizon One!

Verizon One brings together a cordless telephone, high-speedDSL

modem and wireless router - all in one convenient unit. Used with
Verizon One, your Verizon Online DSL connection enables you and
your household to have one place to access your communications,
plus access to information like Weather, News, Sports and Movie
Listings on the touch-screen display.

Your kit contains everything you need to set-up Verizon One

and

install your Verizon Online DSL Service if you are a new subscriber.

© 2006 Verizon

Verizon One Quick Start Guide

3

Base Unit

Step 1

Attach the Verizon One Base Unit to
the Swivel Support Stand (Figure 1).

Firmly snap the Verizon One Base Unit
Swivel Support Stand onto the back of
the Base Unit. Locate a sturdy, flat
surface, table or desktop near an active
wall AC power outlet, an active telephone
jack and your primary computer.

Step 2

Plug in the Power Cord (Figure 2).

Connect the DC 12V power supply cord
to the power connector marked 12V DC
on the rear panel of the Verizon One
Base Unit. Plug the other end of the
power supply into an AC wall socket, and
then turn on the power switch (if it is not
on already). Check the Base to see if the
Power LED is solid green. If the Power
LED is solid green, Verizon One power
is on.

Step

3

Follow the Instructions on the Verizon
One Display (Figure 3).

The Verizon One display will walk you
through the necessary steps to complete
the set-up of Verizon One and the
installation of your Verizon Online DSL
Service (if required).

Get Started

Follow these Step-by-Step instructions
to set-up your Verizon One:

Power is OnFigure 1 Figure 2 Figure 3

© 2006 Verizon

Verizon One Quick Start Guide

4

Step 4

Connect the Cordless Handset Battery
(Figure 4).

Remove the battery cover by pressing
and sliding the cover off the battery
compartment. Attach the battery cable
connector to the connector socket inside
the battery compartment, and then slide
the battery into the compartment. (Note:
Prior to replacing the battery cover,
be sure that the battery cables will not
obstruct the compartment when the cover
is replaced). Replace the battery cover by
sliding the cover upward until it snaps into
place on the Handset.

Note: Prior to using your Verizon One
Handset for the first time, the Handset
battery must be fully charged. To charge
the Handset, place it into the cradle with
the keypad face down so the contacts on
the Handset touch the contacts on the
Base Unit. Allow the battery to charge for
approximately 12 hours before using it for
the first time.

Cordless Handset

Figure 4

© 2006 Verizon

Verizon One Quick Start Guide

5

Step 5

Register the Cordless Handset
(Figure 5).

Registering the Cordless Handset allows
the Handset to communicate with the
Base Unit. To register the Handset to the
Base Unit, perform these steps

:

1. Select the <Menu> function on the
Handset.

2. Using the round navigation button,
scroll down to find the [Registration]
menu. Next, press the top left corner
key to select Registration.

3. Once you have selected Registration,
the Handset will instruct you to press
and hold the <Intercom> key on the
Base Unit. Press and hold this key for
3 seconds.

4. After 3 seconds, the Handset will
automatically register to the Base Unit

To verify successful registration, press
the <Talk/Flash> button on the Handset.

A dial tone will be emitted from the

Handset and a call may be placed
successfully. If no dial tone is emitted,
but the Handset indicated that it
successfully registered with the Base,
verify that the Base Unit is connected to
an active telephone line and that this line
is plugged into the DSL/Phone port on
the back of the Base Unit.

Standard Cordless Phone Features

You get all the features you’re used to
– Mute, Flash, Hold, Phone Book and
Redial.

You’re now ready to use Verizon One!

Figure 5