Verizon 2655 Service manual

Important Safety Instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water (for example, near a bath tub, kitchen sink, or swimming pool).

5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage.

6. Slots and openings in the Handset and Base Unit are provided for ventilation. To protect it from overheating, these openings must not be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation where proper ventilation is not provided.

7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not install this product where the cord might be damaged by anyone walking on it.

9. Never push objects of any kind into this product through holes and slots in the Handset and Base Unit as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.

10. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing cabinet parts other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the appliance is subsequently used.

11. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.

Important Safety Instructions

12. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions:

A. When the power supply cord or plug is damaged or frayed. B. If liquid has been spilled into the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating instructions, because improper adjustment of other controls may result in damage and will often require extensive work by an

authorized technician to restore the product to normal operation. E. If the product has been dropped and the cabinet has been damaged. F. If the product exhibits a distinct change in performance.

13. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

14. Do not use the telephone to report a gas leak in the vicinity of the leak.

SA VE THESE INSTRUCTIONS

Introduction

The 2655 is an advanced cordless telephone that operates in the 2.4 GHz frequency range.

This manual is designed to familiarize you with the 2655 cordless telephone.

IMPORTANT

Please record the Base ID code (BS ID) printed on the underside of the 2655 Base in the space below. Please be certain to include all 15 digits/ characters.

Base ID#

Parts Check List

1. Base Unit

2. Handset

3. AC Power Adapter

4. Telephone Cord

Handset

5. Battery Pack

6. Belt Clip

7. User's Manual

Base Unit

Battery Pack

AC Power Adapter

Telephone Cord

Belt Clip

The Handset Layout

2 3

4 5

1. Antenna

2. Message Waiting Indicator

3. Earpiece

4. Headset Jack (2.5mm)

5. Scroll Keys

6. On/Flash

7. Dialing Key (0 - 9, *, #)

8. Handsfree Speakerphone

12 13

9. LCD Display

10. Select

11. Off/Clear

12. Intercom

13. Billed Services

14. Microphone

The Base Unit Layout

THAT MAY CAUSE UNDESIRED OPERATION.

PRIVACY OF COMMUNICATIONS MAY NOT BE ENSURED WHEN USING

THIS PHONE.

USOC JACK: RJ11C/RJ11W

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION

IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MAY

NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST

ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE

REGISTRATION NO.: EW7 CHN-34723-WI-E

RINGER EQUIVALENCE: 0.0B

COMPLIES WTH 47 CFR PART 68

MODEL : 2652

MANUFACTURED IN CHINA

HAC

FCC ID: EW780-5001-00

AC Power Jack

Phone Cord Jack

Page Key Charge Indicator Power Indicator In Use Indicator

Erase Key Skip Key Redial Key Flash Key Hold Key

Mute Key Play Key

Volume Keys

Dialing Keys (0 - 9, *, #)

Speaker Key

Auto Callback Key 3-Way Calling Key Repeat Dialling Key Voicemail Key

Charging Contacts

Setup

Plug the AC power adapter into an electrical outlet, and the DC connector into the back of the Base Unit.

To AC outlet

FCC ID: EW780-5001-00

HAC

MODEL : 2652

MANUFACTURED IN CHINA

REGISTRATION NO.: EW7 CHN-34723-WI-E

RINGER EQUIVALENCE: 0.0B

COMPLIES WTH 47 CFR PART 68

USOC JACK: RJ11C/RJ11W

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION

IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MAY

NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST

ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE

THAT MAY CAUSE UNDESIRED OPERATION.

PRIVACY OF COMMUNICATIONS MAY NOT BE ENSURED WHEN USING

THIS PHONE.

To telephone socket outlet

To AC power jack

To telephone jack

Connecting to phone line

Plug one end of the telephone line cord into the jack on the back of the Base Unit. Plug the other end of this cord into the wall jack.

Checking for dial tone

After the battery is charged press ON on the Handset. The Phone icon will appear on the Handset display, and you will hear dial tone. If not, see

In Case of Difficulty.

Tone/Pulse selection

See BASE SETTINGS for details.

CAUTION: Use only the power supply provided with your 2655 Unit.

IMPORTANT: For best performance the 2655 should be installed as follows:

In an elevated location, in the center of the room, with no obstructions nearby.

In a location that is away from other electrical appliances such as microwave ovens, personal computers, or

televisions.

Getting Started

Installation of Battery Pack in Handset

Follow the steps below:

1. Remove battery compartment

2. Place the new battery pack in

Getting Started

3. Replace the battery

4. If the new battery pack is not

cover by pressing on the indent and sliding downward.

the Handset with the metal contacts aligned with the charge contacts in the battery compartment.

compartment cover by sliding it upwards.

already charged, place the Handset in the Base Unit, or a charging stand, and allow it to charge for 10-12 hours. After initial charge, a maintenance charge of 8 hours should be sufficient.

Spare Battery Charger/Power Backup Function

CAUTION: TO

REDUCE RISK OF FIRE,

USE ONLY VTECH

80-5017-00-00

CAUTION: TO

REDUCE RISK OF FIRE,

USE ONLY VTECH

80-5017-00-00

BATTERY INSTALL THIS SIDE UP

The 2655 can use the spare battery in the Base Unit to provide operational backup in the event of a power failure. With a fully charged battery pack in the spare battery charger, you will still be able to place and receive calls from the Handset for up to 3 hours.

The spare battery pack can also be used to replace a drained Handset battery, ensuring uninterrupted use.

A spare battery can be purchased from most retail stores that carry electronic equipment.

NOTE:

When using the 2655 during Power Backup mode, audio quality may be compromised due to reduced Power availability. The Base Unit can't be used

when in power backup mode.

PRIVACY OF COMMUNICATIONS MAY NOT BE ENSURED WHEN USING

THIS PHONE.

THAT MAY CAUSE UNDESIRED OPERATION.

NOT CAUSE HARMFUL INTERFERENCE; AND 2) THIS DEVICE MUST

ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE

REGISTRATION NO.: EW7 CHN-34723-WI-E

RINGER EQUIVALENCE: 0.0B

USOC JACK: RJ11C/RJ11W

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION

IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1)THIS DEVICE MAY

COMPLIES WTH 47 CFR PART 68

MODEL : 2652

MANUFACTURED IN CHINA

HAC

FCC ID: EW780-5001-00

1. Open the spare battery charger by pressing the release button, located on the right-hand side of the Base Unit. A drawer will open to reveal the spare battery compartment.

2. Place a battery pack in the drawer with the charge contacts facing up and to the left.

3. Push the drawer closed.

The spare battery takes 24 hours to fully charge a drained battery.

Getting Started

BATTERY INSTALL THIS SIDE UP

CAUTION: TO

REDUCE RISK OF FIRE,

USE ONLY VTECH

80-5017-00-00

Charging Of Handset Battery Pack

The Handset of your 2655 cordless telephone is powered by a rechargeable battery pack. It charges automatically whenever the Handset is in the Base Unit.

You should charge the battery pack for 12 hours when you first receive your phone. You'll know the battery pack needs charging when:

Getting Started

• The low battery message is displayed:

• The Handset seems completely dead, the LCD is completely clear and does not activate when you press the keys.

CAUTION: to reduce the risk of fire or injury to persons by battery, read and follow these instructions.

1. Use only the appropriate type and size battery pack specified in the instruction manual provided for this product.

2. Do not dispose of the battery pack in a fire. The cell may explode. Check with State and local codes for possible special disposal instructions.

3. Do not open or mutilate the battery pack. Released electrolyte is corrosive and may cause damage to the eyes or skin. It may be toxic if swallowed.

4. Exercise care in handling battery in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns.

5. Charge the battery pack provided with or identified for use with this product only in accordance with the instructions and limitations specified in theinstruction manual.

6. Observe proper polarity orientation between the battery pack and battery charger.

Handset and Base Indicators

Handset Icons

Icon

Description

Line In Use indicator On steady with no number next to it when a parallel set is in use. On steady with one or more numbers next to it, indicating which extensions are using the line. For example, 12 indicates that Handset 1 and Handset 2 are on an outside call.

Intercom indicator On steady with the extension numbers currently on an

intercom call. For example, 02 indicates that the Base and Handset 2 are on an intercom call.

Battery indicator Cycles (Low, Medium, and High) when Handset battery is charging. Flashes when a low battery condition is detected.

Mute indicator On steady when the Handset microphone is muted.

Hold indicator On steady when the line is on hold.

Range Extender indicator On steady when the Range Extender is on.

Handset Registration indicator

is displayed when a Handset is either not registered, or

is searching for a Base Unit.

Basic Operation

Handset and Base Indicators

Handset LEDs

LED

Message Waiting

Description

• Flashes to indicate that you have new messages in your voicemail. Service must be subscribed to through your local telephone company.

Base LEDs

LED

VOICEMAIL

Power

Basic Operation

In Use

Charge

Mute

Description

• Flashes to indicate that you have new messages in your voicemail. Service must be subscribed to through your local telephone company.

• Lights when Base unit is receiving power from wall outlet.

• Flashes when unit is in Power Backup mode.

• Lights when line is being used by any Handset of the 2655 system.

• Flashes when another telephone on the same line (parallel extension) is in use.

• Flashes following ringing cadence while the phone is ringing.

• Lights whenever the Handset is placed in the Base Unit charging cradle.

• Flashes briefly when put a spare battery in the spare battery compartment.

• Lights when Base microphone is muted.

Speaker

• Flashes when HOLD function is activated.

• Lights when Base speaker is in use.

Soft Menu Functions

The 2655 has an advanced design that uses a menu structure and soft keys to access all of the built-in features.

Example of the idle mode display:

RDL (Redial)

Press RDL to display the last 5 telephone numbers dialed. The number on top line is the most recent number dialed.

• Use the

• To dial the number, you can simply press the ON or HANDSFREE key.

To Save Redial to Memory: Use the scroll keys to select the desired number. Then press SELECT. Press

SAVE. Use the steps from 3 to 5 of To Store a Number/Name. To Erase Redial:

Use the scroll keys to select the desired number. Then press SELECT. Press ERASE.

scroll keys to select the desired number.

With the Handset in the idle (OFF) mode, press the MENU key to access the following options:

• CALLS LOG (CALLER ID)

• NAME AND NUMBER ANNOUNCE

• HANDSET SETTINGS

• RANGE EXTENDER

• TONE/PULSE

• REGISTER (Both Handsets previously registered to the Base Unit at the

factory.)

• VOICEMAIL SETUP

Use the

scroll keys to select the desired option, then press OK.

Basic Operation

Calls Log (Caller ID)

From the idle (OFF) mode, press MENU, use the keys to select CALLS LOG, then press

OK. The Caller ID information of the most recently received call will be displayed.

To scroll to other records, use the

scroll keys.

To dial the number displayed, you can simply press the ON or HANDSFREE key.

You can also press the CID key to access the following options (DEL, OPT#, SAVE):

DEL: Select this option to delete THIS or ALL records in Caller ID memory. OPT#: Select this option to display up to four possible dialing strings of

Basic Operation

the number stored in Caller ID memory. If a number is provided in the Caller ID data, the possible options to choose from will be either 7, 8, 10, or 11 digits. For example, if the original number in Caller ID menory was 808-880-8808, then the display options will be:

scroll

555-123-4567

Use the keys to make selection, and

then press DIAL, ON or HANDSFREE to dial the number.

SAVE: Select this option to save the displayed Caller ID record into

Phonebook Memory. Only Caller ID records with telephone numbers can be saved into Phonebook Memory. If you need to modify the number after saving, see To Edit a Name or a Number.

Caller ID - Call Waiting ID

Your 2655 is capable of displaying the name and/or number of the party calling before you answer the phone (Caller ID). It is also capable of displaying Caller ID information in conjunction with a Call Waiting alert signal (Call Waiting Caller ID). With Call Waiting Caller ID, the Caller ID data is displayed so you can decide whether to answer the incoming call, or continue with your current conversation.

NOTES ABOUT CALLER ID & CALL WAITING CALLER ID

These are subscription services, provided by most regional telephone service providers. You must subscribe to these services to get the benefits of these features. If you do not subscribe to Caller ID services, you can still use

your 2655 and the other features it offers. Due to regional incompatibilities, Caller ID information may not be available

for every call you receive. In addition, the calling party may intentionally block their name and phone number from being sent.

123-4567

1-123-4567

555-123-4567

1-555-123-4567

+ 32 hidden pages