Veris H608 Installation Instructions

Download

Page 1

Installation Guide

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Follow safe electrical work practices.

See NFPA 70E in the USA, or applicable local codes.

• This equipment must only be installed and serviced by qualiﬁed electrical personnel.

• Read, understand and follow the instructions before installing this product.

• Turn oﬀ all power supplying equipment before working on or inside the equipment.

• Use a properly rated voltage sensing device to conﬁrm power is oﬀ. DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION

• Only install this product on insulated conductors.

Failure to follow these instructions will result in death or serious injury.

A qualied person is one who has skills and knowledge related to the construction and operation of this electrical equipment and the installation, and has received safety training to recognize and avoid the hazards involved. NEC2009 Article 100

No responsibility is assumed by Veris Industries for any consequences arising out of the use of this material.

DANGER

Current Monitoring

Product Overview

The H608 is a current-sensitive switching device that monitors current (amperage) in the conductor passing through it. A change in amperage in the monitored conductor that crosses the switch (setpoint) threshold plus the hysteresis value causes the resistance of the FET status output to change state, similar to the action of a mechanical switch. In this model, the setpoint is adjustable through the action of a twenty (20) turn potentiometer (see the

RoHS

Compliant

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classiﬁed locations.

• The installer is responsible for conformance to all applicable codes.

• Mount this product inside a suitable ﬁre and electrical enclosure.

Calibration section). The status output is suitable for connection to building controllers or other appropriate data acquisition equipment operating at up to 30 volts. The H608 requires no external power supply to generate its output.

Speciﬁcations

H608

Split-Core Current Switch, Adjustable Trip Point

Sensor Power

Amperage Range

Status Output Ratings

Insulation Class

Setpoint

Frequency Range

Temperature Range

Humidity Range

Hysteresis

Off State Resistance

On State Resistance

Terminal Block Max. Wire Size

Terminal Block Torque

Agency Approvals

Installation Category

Induced from the monitored conductor

0.5 to 175 A continuous

N.O. 1.0 A@ 30 VAC/DC, not polarit y sensitive

600 VAC RMS (UL); 30 0 VAC (CE )

Adjustable, 0.5 A or less

50 /60 Hz

-15° to 60°C ( 5° to 140°F)

10-9 0% RH non-condensing

10% t ypic al

Open switch represents >1 MΩ

Closed switch represents < 200 mΩ

24 to 14 AWG (0.2 to 2.1 mm2)

3.5 to 4.4 in-lbs (0.4 to 0.5 N-m)

COMPLIANCE INFORMATION

UL508 open device listing, CE: EN61010 -1

Cat. III, pollution degree 2

Alta Labs, E nercept, Ensp ector, Hawkeye, Trus tat, Aerospo nd, Veris, and th e Veris ‘V’ log o are tradema rks or registe red tradema rks of Veris Ind ustries, L. L.C. in the USA and /or other countri es.

For applications requiring double or reinforced insulation, please contact the factory. The product design provides basic insulation only. Do not use the LED indicators as evidence of applied voltage.

Other companies’ trademarks are hereby acknowledged to belong to their respective owners.

Page 2

Installation Guide Current Monitoring H608

Dimensions

Installation

Removable Mounting Bracket

0.6"

2.1"

(54 mm)

0.4” x 0.2”

(10 mm x 5 mm)

Slot (2x)

(16 mm)

0.5"

(13 mm)

(54 mm)

2.9"

(74 mm)

3.5"

(89 mm)

2.1"

0.7"

(18 mm)

1.2"

(31 mm)

2.5" *

(64 mm)

1.0" *

(26 mm)

Disconnect and lock out power to the enclosure containing the conductor to be monitored.

1. Locate a mounting surface for the removable mounting bracket that will allow the monitored conduc tor to pass through the center window when it is installed and that will keep the product at least ½” (13 mm) from any uninsulated conductors. Determine cable routing for the controller connection, allowing the wiring to reach the mounting location.

2. Drill holes to mount the bracket to the chosen surface using the included screws.

CONTACTOR

Insulated Conductor ONLY

DDC CONTROLLER

3. Wire the output connections from the sensor to the controller (solidstate contact).

4. Snap the sensor over the conductor and clip the assembly to the mounting bracket.

5. Secure the enclosure and reconnect power.

6. Calibrate the sensor with the load running normally.

Fan

Motor

Other companies’ trademarks are hereby acknowledged to belong to their respective owners.

Page 3

Installation Guide Current Monitoring H608

Notes

For load currents greater than sensor maximum rating:

Use a 5 Amp (H68xx series) current transformer (CT) as shown. This technique can be combined with wrapping (see below) to add range for a low current load on a high current source.

>175 A (sensor max.)

240A

DANGER: 5A CTs can present hazardous voltages. Install

300A:

H68 xx-5A CT

CTs in accordance with manufacturer's instructions. Terminate the CT secondary before applying current.

For load currents less than sensor minimum rating:

Wrap the monitored conductor through the center window and around the sensor body to produce multiple turns. This increases the current measured by the transducer. Program the controller to account for the extra turns (e.g., if four turns pass through the sensor (as shown) divide the normal reading by 4).

< 0.5 A (Sensor Min.)

0.5A

0.3 A

• Derate the product’s maximum current for the number of turns through the sensing window using the following formula.

Rated Max. Amps ÷ Number of Turns = Max. monitored Amps

e.g. : 100A ÷ 4 Turns = 25 Amps max. in monitored conductor

• Failure to follow these instructions can result in overheating and permanent equipment damage.

CAUTION

RISK OF EQUIPMENT DAMAGE

Other companies’ trademarks are hereby acknowledged to belong to their respective owners.

Page 4

Installation Guide Current Monitoring H608

Calibration

Before beginning calibration, establish normal load conditions. Then choose either A or B below.

A. To monitor under-current (belt loss, coupling shear, status)

Status

1. Turn setpoint screw clockwise until Status Open LED turns on.

2. Slowly turn the screw counter clockwise until the Status Closed LED turns on.

CLOSED

Status OPEN

Status

CLOSED

Status OPEN

Setpoint

3. Turn the screw an additional ¼ turn counter clockwise for

Setpoint

operational margin.

B. To monitor over-current (mechanical problems, seized impeller)

Status

1. Turn setpoint screw counter clockwise until Status Closed LED turns on.

CLOSED

Status OPEN

Setpoint

Troubleshooting

Status

2. Slowly turn the setpoint screw clockwise until the Status Open LED just turns on.

CLOSED

Status OPEN

Setpoint

3. Turn the setpoint screw an additional ¼ turn clockwise

Setpoint

for operational margin.

Problem Solution

No Reading at Controller • Check sensor calibration (see above)

• Check for control voltage at sensor (<30V, <1A)

• Check for amperage in monitored conductor (> 0.5A)

• Assure that sensor core mating surfaces are clean and that the core clamp is completely closed

Setpoint screw has no stops The setpoint screw has a slip-clutch at both ends of its travel to avoid damage. Twenty turns CCW will

Both LEDs are lit Setpoint screw is too far clockwise. See solution above.

reset the sensor to be most sensitive. Repeat calibration above.

Other companies’ trademarks are hereby acknowledged to belong to their respective owners.

Veris H608 Installation Instructions

Specifications and Main Features

Frequently Asked Questions

User Manual