Veris H10F Datasheet

H10 F

Current Switch: Auto Calibration, Process Control

VERIS INDUSTRIES

Automatically Learns At Initial Power-Up

DESCRIPTION

The Hawkeye TruStat H10F is a microprocessor based, self-learning, self-calibrating current switch. It provides calibration-free status, for both under-current and overcurrent conditions. At initial power-up, the H10F automatically learns the average current on the line with no action required by the installer. Once a current is learned, the switch monitors for changes in current greater than ±20% of the learned load.

APPLICATIONS

● Verifying lighting circuit and other electrical service run times

● Monitoring status of industrial process equipment

● Monitoring status of critical motors (compressor, fuel, etc.)

current monitoring

PRODUCT FUNCTIONS

ALARM RESET

5% Typical +20% +15%

H10F

Hawkeye® TruStat™

FEATURES

● Automatic adjustable trip point (3.5-100A)...precise control of current trip point

● 100% solid state...no moving parts to fail

● Removable mounting bracket for installation exibility

● 5-year warranty

● Automatic calibration...reduced errors and installation costs

● Microcontroller based learning technology...automatically learns load upon

initial power-up...eliminates labor associated with calibration

● Monitors current for both under- and over-load in one package

● Small size ts easily inside small starter enclosures...saves space

NOMINAL LEARNED CURRENT

-15%

-20%

ØAAC ØAAC

POWER

LEARN

(MODE) 30 SEC

SPECIFICATIONS

Sensor Power Induced from monitored conductor Isolation 600VAC RMS (UL); 300VAC RMS (CE) Temperature Range -15° to 60° C (5° to 140°F) Humidity Range 10-90% RH non-condensing Frequency Range 50/60 H z Trip Point Calibration Learn Period 30 sec. learn period Normal-to-Alarm Status Output Delay 1 second max. Alarm-to-Normal Status Output Delay 30 seconds nominal* Status Output ±20% of learned current to trigger alarm; ±15% of learned current to release alarm (see graph) Terminal Block Wire Size 24-14 AWG (0.2 to 2.1 mm2) Terminal Block Torque 3.5 to 4.4 in-lbs (0.4 to 0.5 N-m) Agency Approvals UL 508 open device listing; CE: EN61010-1:2001-02, CAT III, pollution degree 2, basic insulation

NORMAL (CURRENT MONITOR MODE)

1 SEC. DELAY 30 SEC. DELAY

Year

Warranty

ALARM (MODE)

NORMAL (CURRENT MONITOR MODE)

POWER LOSS

ALARM (MODE)

Maximize Reliability

Minimize Installed Cost

*If current switch experiences a momentary loss of power, 30 second delay may or may not apply. Do not use the LED status indicators as evidence of applied voltage.

800.354.8556

+1 503.598.4564

www.veris.com

HQ00 01757.B 01131

800.354.8556

E150462

+1 503.598.4564

www.veris.com

DIMENSIONAL DRAWING

H10F

Removable Mounting Bracket

0.6"

(16 mm)

2.1"

(54 mm)

0.4” x 0.2”

(10 mm x 5 mm)

Slot (2x)

* Terminal block may extend up to 1/8” over the height dimensions shown.

0.5"

(13 mm)

2.1"

(54 mm)

2.9"

(74 mm)

(18 mm)

0.7"

3.5"

(89 mm)

1.2"

(31 mm)

2.5" *

(64 mm)

1.0" *

(26 mm)

HOW IT WORKS

The compact split-core H10F current switch monitors a learned load current to detect power loss and electrical overload of fans, blowers, pumps, chillers, or any other critical motor functions. The push-button initiated LEARN MODE allows resetting of the monitored current when the load changes due to system alterations.

LEARN MODE

● Unit automatically enters LEARN MODE upon initial power-up

● Auto-calibration is achieved by averaging the load current for 30 seconds

● During this stage, green and red LEDs blink on/o

● STATUS OUTPUT contacts are closed

● LEARN MODE may be initiated manually

NORMAL MODE

● Initiated after the 30-second learning period, or immediately upon power-up if

sensor has already learned a load

● The red LED is o, and the green LED is blinking

● STATUS OUTPUT contacts are closed

APPLICATION/WIRING DIAGRAM

Monitoring Fan /Pump Motors for Positive Proof of Flow

CONTACTOR

Insulated conductor only

Motor

ALARM MODE

● The ALARM state signals low current, high current, or power loss conditions

● Initiated within 1 second when any load current excursion exceeds a nominal

±20%

● ALARM will persist until the load current returns to within a nominal ±15% of

the learned current value, or when power is restored to normal

● The 5% ALARM-to-NORMAL MODE reentry margin prevents alarm signal

oscillations. This feature is enhanced by a 30 second delay, to insure true nominal load current conditions when returning to NORMAL MODE from an ALARM state

● The green LED shuts o, and the red LED blinks

● STATUS OUTPUT contacts are open

OPERATING MODES STATUS LEDS STATUS

GREEN RED

LEARN (30 sec s) Alternating Blink On/O Contacts Closed

NORMAL Blink O Contacts Closed

ALARM* O Blink Contacts Open

DDC CONTROLLER

Pump or Fan

OUTPUT

current monitoring

* 1 sec maximum after detection.

ORDERING INFORMATION

MODEL AMPERAGE

RANGE

STATUS OUTPUT NOMINAL TRIP POINT

TARGET RANGE*

RoHS

Compliant

NOMINAL

ALARM RESET

RANGE*

H10F 3.5 - 100A N.O. 1.0A@30VAC/DC ±20% ±15% Split-core

*For best performance, monitor 5A or more current. At currents less than 5A, these ranges are approximate.

Listed for use on 75°C insulated conductors.

ACCESSORIES

DIN Rail Clip Set (AH01) DIN Rail (AV01) and DIN Stop Clip (AV02)

HQ00 01757.B 01131

AH01

AV01

HOUSING STATUS

LED

UL CE RoHS

n n

AV02