Veris EP2 Datasheet
EP Series transducers are sold as an open device.
EP SERIES
Electropneumatic Transducers
Micro-Controlled With HighPerformance, Low-Power Coil
VERIS INDUSTRIES
Poppet Valve Technology
DESCRIPTION
The EP2 Series electropneumatic pressure transducer uses micro-controlled poppet
valve technology for highly accurate pressure sensing in multiple applications. The
poppet valves consume no air, eliminating unnecessary air losses in the system and
allowing for stable and reliable operation. The EP2 is comes installed on standard
SnapTrack, and an optional dust cover is available to protect from the environment.
An LCD display and LED indicators make it easy to read system status at a glance.
APPLICATIONS
● Hospitals
● Schools
● Pneumatic dampers/actuators
PRESSURE
EP2
FEATURES
● Field-selectable 4-20mA/0-5V/0-10VDC input for application exibility
● Poppet valve technology for quiet operation
● Manual override with set and hold feature...great for commissioning
those leaky systems
● Multi-point calibration; 3-15 psi (5 point calibration) and 0-20 psi
(6 point calibration)
● Pressure loss alarm provides a contact closure if the EP2 is unable to
achieve the desired output within a xed length of time
● Failsafe vent solenoids bleed branch pressure on power failure for added safety
● Optional transparent plastic dust cover (AA43) protects units from dust
and tampering (required for CE)
Year
SPECIFICATIONS
Input Power 24VAC/DC nominal, 30VAC max.; 150mA max.
Control Input 4-20mA/0-5V/0-10VDC; jumper-selectable
Input Impedance 4-20mA, 250Ω; 0-5V/0-10VDC, 10 kΩ
Manual Override Jumper-selectable mode, digital pushbutton adjust
Alarm Contact 100mA@30VAC/DC (Pressure loss, manual mode, jumper selec table)
Accurac y 1% FS; combined linearit y, hysteresis, repeat ability
Compensated Temperature Range -4° to 65°C (25° to 140°F)
Temperature Coecient ±0.05%/°C
Operating Environment 10-90% RH noncondensing
Air Capacity 523 in3/min @ 45 psi (8570 cm3/min @ 310.3 kPa); 333 in3/min @ 20 psi (5456 cm3/min @ 137.9 kPa)
Supply Pressure 45 psig max.
Control Range 0-20 psig or 3-15 psig, jumper-selectable
Pressure Dierential 0.1 psig (supply to branch)
Pressure Indication Electronic, 3-1/2 digit LCD
Minimum Tubing Length 15 fe et*
Port Connection 1/8” i.d. poly tubing
Media Connection Clean, dry air, or inert gas. Do not use with oxygen service
*For shorter tubing runs use AA45 Pneumatic Capacitor
EMC Conformance: Low voltage directive 2006/95/EC; EMC directive 2004/108/EC.
EMC Special Note: Connect this product to a DC distribution network or an AC/DC power
adaptor with proper surge protection (EN 61000-6-1:2007 specication requirements).
800.354.8556
5
Warranty
+1 503.598.4564
www.veris.com
HQ0001828.B 01131
Observe handling precautions for static sensitive
devices to avoid damage to the circuitry which
would not be covered under the factory warranty.
800.354.8556
+1 503.598.4564
www.veris.com
APPLICATION/WIRING DIAGRAMS
FROM CONTROL
SYSTEM
GND/COMMON
INPUT SIGNAL
POWER
TO DIGITAL INPUT - OPTIONAL
PRESSURE LOSS ALARM
DIMENSIONAL DRAWINGS
3.3"
(84 mm)
3.5"
(89 mm)
4.9"
(125 mm)
CONFIGURATION
INPUT
VOLTAGE
MODE
MODE
GND/COM
Dust Cover
POWER
INPUT SIGNAL
Current
0-5V
Voltage
SIDE VIEW FRONT VIEW
MANUAL ADJUST
OPERATION
MODE
PRESSURE
RANGE
0-20psi
3-15psi
Auto
Manual
0-10V
Slide Switch Option Available
ALARM
MODE
ON
2.1"
(53 mm)
PRESSURE
OFF
(OPTIONAL)
LOSS
ALARM
(46 mm)
ORDERING INFORMATION
Output
1
EP2
= Selectable
3-15 /0-2 0 ps i
EP 2 1 0 0 S 1
Feedback
0 = None
1 = Pressure
Loss Alarm
2 = Manual
Mode A larm
Examp le:
Failsafe
0 = None
1 = Vent on
Powe r Fail
Option = S lide Switch A uto
Manual Mode
1.8"
US or EU
S = Standard
C = CE, includ es
cover plate
If the dust cover is ordered, the EP2
is mounted to a longer Snaptrack.
pressure
Available
Option
Blank = none
1 = Slide Switch /
Auto/Manual
2 = EP Cover Plate
3 = Slide Switch /
Auto Manual plus
EP cover plate
ACCESSORIES
Steel Bracket (AA23), Dust cover (AA43)
Pneumatic Capacitor (AA45)
HQ0001828.B 01131
AA45
AA43
AA23
Loading...