Veris E682x Installation Instructions

POWER MONITORING

INSTALLATION GUIDE

E682x SERIES

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.

• This equipment must only be installed and serviced by qualied electrical personnel.

• Read, understand and follow the instructions before installing this product.

• Turn o all power supplying equipment before working on or inside the equipment.

• Use a properly rated voltage sensing device to conrm power is o. DO NOT DEPEND ON THIS PRODUCT FOR VOLTAGE INDICATION

E682x SERIES

0.333 VAC Solid-Core Current Transducers

Installer’s Speciﬁcations

Inputs:

Frequency Range 50/60 Hz Leads 6’ (1.8 m)

Accurac y:

Accuracy ±0.5% from 5%-120% of rated current

Outputs:

Output at Rated Current 0.333 VAC

Mechanical:

Insulation 60 0 VAC

Environmental:

Operating Temperature Range -40° to 85°C (-4 0° to 185°F) Storage Temperature Range -50° to 105°C (-58° to 221°F) Humidity Range 0-95% noncondensing Altitude of Operation 3 km max. Installation Categor y Cat III, pollution degree 2 Agency A pprova ls UL61010 -1, EN61010 -1

InstallatIon

Installation must be performed by a qualiﬁed electrician. Disconnect and lock out power to the primary circuit before installing these current transducers (CTs).

Failure to follow these instructions will result in death or serious injury.

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classiﬁed locations.

• The installer is responsible for conformance to all applicable codes.

• Mount this product inside a suitable ﬁre and electrical enclosure.

Documentation must be consulted where this symbol is used on the product.

This symbol indicates an electrical shock hazard exists.

Always use this product in the manner specied or the protection provided by the product may be impaired. This product must be installed in an appropriate Fire and Electrical enclosure per local regulations.

1. Connect the transducer output leads to the meter or device inputs. The white wire is the X1 lead. Note the labeling on the product indicating the source side, or the base of the arrow.

2. Run the conductor to be monitored through the CT center and complete connections.

3. Check wire terminations for tightness.

4. Reconnect power to the panel.

Product IdentIfIcatIon

PART NUMBER DESCRIPTION

E682A051V3 Solid-Core Volt CT, 50A:0.333V, 0.417 in ID, 6 ft leads E682A101V3 Solid-Core Volt CT, 100A:0.333V, 0.417 in ID, 6 ft leads E682C201V3 Solid-Core Volt CT, 200A:0.333V, 1.0 in ID, 6 ft leads E682D401V3 Solid-Core Volt CT, 400A:0.333V, 1.25 in ID, 6 ft leads

Other lead lengths are availa ble. Consult a sales rep for more i nformation.

Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and /or other count ries.

E682x SERIES

INSTALLATION GUIDE

oPeratIon

The E682x series of 0.333 volt solid-core current transducers provide secondary AC voltage proportional to the primary (sensed) current. For use with power meters, data loggers, chart recorders, and other instruments, E682x CTs provide a costeective means to transform electrical service amperages to a voltage compatible with monitoring equipment.

These products provide basic insulation to 600 VAC between the sensed conductor and the output leads. For reinforced applications, the sensed conductor must be provided with appropriate insulation. Reinforced insulation is provided for applications to 300 VAC between the sensed conductor and the output leads under UL/IEC/EN 61010-1 rules.

dImensIons

+ +

Ø = E

notes

Accuracy is specied with the primary conductor(s) centered in the CT window.

Do not apply current transducers to circuits having a phase-to-ground/neutral voltage greater than the stated maximum voltage without applying adequate additional insulation between the primary conductor and the current transducers. Veris assumes no responsibility for equipment damage or personal injury caused by transducers operated on circuits above their published ratings.

#22 AWG Stranded

White Black

1 2

PVC insulation,

UL1015, 600V, 105˚C

0.250” ± 0.050”

(6.35 mm ± 1.27 mm)

Black

Model L A B C D E

E682A051V3 E682A101V3

E682C201V3

E682D401V3

6’

(1.8 m)

6’

(1.8 m)

6’

(1.8 m)

1.3"

(33 mm)

2.3"

(59 mm)

2.8"

(70 mm)

1.5"

(38 mm)

2.6"

(66 mm)

3.2"

(82 mm)

0.7"

(18 mm)

0.7"

(18 mm)

1.0"

(25 mm)

0.8"

(21 mm)

1.2"

(31 mm)

1.4"

(36 mm)

White

0.4"

(10 mm)

1.0"

(25 mm)

1.25"

(31 mm)

Alta Labs, Enercep t, Enspector, Hawkeye, Trustat, Veris, and the Veris ‘ V’ logo are trademark s or registered tradema rks of Veris Industries, L.L .C. in the USA and /or other count ries.