Veris CWV Installation Instructions

4.6"

(116 mm)

3.3"

(84 mm)

1.4"

(36 mm)

(42 mm)

ENVIRONMENTAL SENSORS

CWV SerieS

Environmental CO2 Sensors

NOTICE

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classied locations.

• Read and understand the instructions before installing this product.

• Turn oﬀ all power supplying equipment before working on it.

• The installer is responsible for conformance to all applicable codes.

INSTALLATION GUIDE

SPECIFICATIONS

Input Vol tage 20 to 30VDC, 24VAC Analog Output #1 4-20mA (clipped & capp ed) or 0-3VDC/0-5VDC/0-10VDC (jumper selectable) Analog Output #2 4-20mA (clipped & capp ed) or 0-3VDC/0-5VDC/0-10VDC (jumper selectable) Sensor Current Draw 200mA Maximum Operating Humidity Range 0-95% RH (noncondensing) Operating Temperature Range 0° to 50°C (32° to 122°F) Housing Material High impac t ABS plastic Relay Contac ts (optional) Form C (SPDT) 1A@30VDC, resistive; 30W ma x.

CO2 Transmitter:

Sensor Type Non-dispersive infrared (NDIR), diusion sampling Measurement Range 0-2000 ppm Accuracy ±40 ppm ±8.5% of measured value Repeatability ±30 ppm ±4.5% of measured value Response Time <60 seconds for 9 0% step change

EMC Conformance: EN 61000- 6-3:2007+A1:2011 Class B, EN 61000-6-1:2007 EMC Special Note: Connect this produc t to a DC distribution network or an AC/DC powe r adaptor with proper surge protection (EN 61000-6-1:2007 specication requirements). RTD/Thermistors are not compensated for internal heating of product.

No responsibility is assumed by Veris Industries for any consequences arising out of the

use of this material.

PRODUCT IDENTIFICATION

Temp/2nd

Output

CWVS

1 = 0-3/5/10VDC an d 4-20 mA 2 = 4-20mA and 4-2 0mA 3 = 0-3/5/10VDC and 0 -3/5/10VD C

MOUNTING

4.6"

(116 mm)

Relay option

X = No relay 1 = Relay

.64”

(16 mm)

Relay option

X = No temp. 1 = Relay B = 100R Pt C = 1k Pt D = 10k T2 E = 2.2k F = 3k H = 10k T3 J = 10k Dale K = 10k with 11kS M = 20k NTC N = 1800 ohm R = 10K US S = 10K 3A1B

3.3"

(84 mm)

Warranty

1 = 1 year 3 = 3 years 5 = 5 years

Housing

Blank = White / gray B = Black

INSTALLATION

1. Select a mounting location with good air circulation. For room installations, mount the sensor 4 ½ feet (1.4 m) above the oor.

2. Remove the cover. Flush mount the CWV on a wall or on a standard US or European single gang junction box.

3. Wire the device. Refer to the wiring diagram.

4. Install the cover.

DIMENSIONS

2.2"

(54 mm)

1.6"

.46"

(12 mm)

Alta Labs, Ene rcept, Enspector, Hawk eye, Trustat, Aerospon d, Veris, and the Veris ‘V ’ logo are tradem arks or registe red trademarks o f Veris Industries, L .L.C. in the USA and/or ot her countries.

NITROGEN

GAS

Regulator Valve

CW V SERIES

INSTALLATION GUIDE

WIRING

POWER SOURCE

20 to 30 VDC

24 VAC

DDC PANEL

COMMON

INPUT mA OR VOLTAGE

Power

Ground

Output #1

V OUT 1 Relay 2

5 3

V OUT 2 Relay 1

5 3

Relay 1 output (optional)

Relay 2/temp output (optional)

Output #2 mA or voltage

mA or voltage

Status 800 1000

Calibrate

CONFIGURATION

1. If so equipped, select the voltage outputs by jumpering the V Out 1 and/or V Out 2, as indicated at left (10=0-10VDC, 5=0-5VDC, 3=0-3VDC).

2. If so equipped, select the relay mode by jumpering the Relay 1 and/or Relay 2 function blocks, as indicated at left (Status=sensor condition, 800=800ppm CO2 setpoint, 1000=1000ppm CO2 setpoint).

LED INDICATION

Green - Power applied to device

Red - Error condition for false reading, CO2 concentration > 10,000 ppm, insucient power, or improperly calibrated sensor.

The red LED briey illuminates for approximately two seconds when the CWV device is initially powered. It then deluminates, indicating normal sensor operation.

OUTPUT SCALING

CO2 PPM 0-3 Volt Output 0-5 Volt Output 0-10 Volt Output mA Output

Outside 300-500 0.45 to 0.75 0.75 to 1.25 1.5 to 2.5 6.4 to 8

Over Ventilated Under 600 Under 0.9 Under 1.5 Under 3 Under 8.8

Ideal Ventilation 600-900 0.9 to 1.35 1.5 to 2.25 3 to 4.5 8.8 to 11.2

Under Ventilated Over 900 Over 1.35 Over 2.25 Over 4.5 Over 11.2

CALIBRATION PROCESS

1. Remove the cover and connect a hose to the plastic port located on the sensing module.

2. Begin nitrogen gas ow (0 ppm CO2). Use a ow rate of 0.3 to 0.5 liter/minute, using the Veris AA01 Calibration Kit or equivalent.

3. Push and hold down the calibration button for 8 seconds.

4. Release the calibration button and verif y that the analog outputs are at either 4 mA or 0 V. If the outputs are not showing these values, repeat steps 3 and 4.

STEP 1

Calibration Port

Connect hose here

STEP 2

Flow Nitrogen

STEP 3

Push and hold calibration button for 8 seconds

Calibration button

Veris AA01 Calibration Kit

(or equivalent)

Note: Do not breathe on the CO2 sensor during the calibration process.