Veracity VHW-HWPS-B4 Quick Start Guide
PRODUCT DIMENSIONS
CONNECTIONS AND LEDS
CONNECTIONS AND LEDS
VHW-HWPS-B4
110 mm
22 mm
121.1 mm
154 mm
RoHS
© Veracity UK Ltd 2016 QSGV1.2 UK
HIGHWIRE POWERSTAR BASE 4 is a trademark of Veracity UK Ltd
LOCATION
A
B
4 x BNC connectors. Connect to any 75 Ohm coaxial cable. 57V Power Supply Options : Connect to either option 1 OR option 2
POE LED
COAX LINK
ACTIVITY
COAX POE
(Power)
A
FUNCTION
Coax data
connection
POE over
coax status
GREEN
Blink = No link to camera
On = 100Base-TX to camera
Flash = 100Base-TX activity
On = Device detected
172.6 mm
B
ETHERNET LED FUNCTION
RJ45 Yellow On = link
C
Blink = activity
RJ45 Green On = Power on
D
05 0706
C D
ORANGE
Blink = 10Base-T link to camera
Flash = 10Base-T activity
On = Approaching power limit
Flash = Short circuit. Check
for cable faults or incompatible
equipment
321
FUNCTIONS
1 57V DC Power
2 57V DC Power
3 SFP Module
4 SFP Top LED
5 SFP Bottom LED
SFP LED OPERATION
Top Red = No module inserted
Green = Device inserted
4
Bottom Off = No module inserted
Red = No device link
5
detected
Green = Link detected
RED
On = Data rate <100%
Cable distance at limit
On = Power limit reached
Flash = POE discontinued
due to overload
4
5
QUICK START GUIDE
4 PORT EOC BASE WITH POE PLUS
HIGHWIRE
POWERSTAR BASE 4
OVERVIEW
APPLICATION DIAGRAM
ETHERNET OVER COAX
TECHNICAL SPECIFICATION
HIGHWIRE Powerstar products are designed to enable the
transmission of standard Ethernet and POE (Power over
Ethernet) over coaxial cables originally installed for analogue
video transmission for CCTV.
These devices can be classed as adaptors or media converters.
They are typically used where analogue CCTV cameras are being
replaced with modern digital network cameras, known as “IP
cameras”. This permits IP cameras to be installed without having
to replace cable and re-wire buildings.
In most CCTV installations, multiple coaxial cable runs will come
together at a central point (e.g. equipment room or control room).
The Base units are located here. Whilst multiple single-channel
HIGHWIRE Powerstar Base units can be used for multiple channels,
it is more cost-effective to provide integrated multi-channel units with
an internal Ethernet switch, allowing more than one coaxial cable to
be connected into the network system per HIGHWIRE device.
HIGHWIRE Powerstar Base 4 provides four coaxial cable
connections. The Base unit has a single standard RJ45 Gigabit
Ethernet port to allow connection to a main network switch.
An SFP socket is also provided to allow a fibre network connection
if required by the application.
All HIGHWIRE Powerstar Base 4 units must be powered through a
DC power connector which is designed for a maximum of 6A at
57V DC.
Either the 1500mA or 800mA Veracity 57V DC Power Supplies are
recommended.
01 0302 04
ETHERNET AND POWER OVER COAX CONNECTION DIAGRAM
ETHERNET
COAX
UP TO 300M ON RG59 / 500M ON RG11
NETWORK
SWITCH
POWER
POWER
SUPPLY
VPSU-57V-1500
OR
VPSU-57V-800
ETHERNET & POE ETHERNET DATA ONLY
VHW-HWPS-B4
HIGHWIRE
POWERSTAR
BASE 4
INSTALLATION
| Connect the coax cable for 1-4 cameras or POE / non-POE
devices to the BNC connectors of the HIGHWIRE Powerstar
Base 4 at the switch end.
| Connect the coax cable to the BNC connectors of the HIGHWIRE
Powerstar Camera units at the camera end.
VHW-HWPS-C
CAMERA
CAMERA
CAMERA
CAMERA
ETHERNET & POE
| Connect 1-4 cameras or POE / non-POE devices to the RJ45 ports
of the HIGHWIRE Powerstar Camera units at the camera end.
| Connect the HIGHWIRE Powerstar Base 4 unit to a network switch.
| Connect the HIGHWIRE Powerstar BASE 4 unit to your chosen
57V Veracity Power Supply. The installation is complete.
Power Input PSU 57V DC up to 6A via a 2 pin detachable
screw terminal (supplied) or a 2 pin Micro-Fit
power connector
EOC Power Output Max 25W per port (POE Plus)
Ethernet Interface Connector type RJ45 Ethernet Gigabit port to
allow connection to a main network switch
HIGHWIRE Interface Connector type BNC 75 Ohm
Range Up to 300m on RG59, 500m on RG11
Bandwith 200Mbps (total up + down)
Dimensions 173 x 121 x 22mm (6.8 x 4.8 x 0.9in) inc clips
Weight 356g (12.5oz) unpackaged
Compliance RoHS, CE, FCC, REACH
Temperature Operating 0°C to 40°C (32°F to 104°F)
Relative Humidity 85% non condensing
Installation The unit is supplied in an aluminium chassis with
rubber feet. It may be used as a stand-alone or
may be rack mounted via available accessories.
IMPORTANT SAFETY NOTES
| This equipment is designed for indoor use only.
| If the equipment is used in a manner not specified by the
manufacturer, the protection provided by the equipment may
be impaired.
| Contact details for Sales and Technical Support can be found
on the Company website: www.veracityglobal.com
Loading...