Page 1
VHW-HWPS-C2
QUICK START GUIDE
2 PORT ETHERNET OVER COAX ADAPTOR
LED FUNCTION
RJ45 Yellow On = link
Blink = activity
RJ45 Green On = POE detected
and enabled
RJ45 Ethernet 10/100Base-Tx
and POE connectors (auto speed,
duplex, crossover, POE/POE Plus)
CONNECTIONS & LEDS
LED
COAX LINK
COAX NET
COAX PWR
(Power)
POE POWER
BUDGET
FUNCTION
Coax data
connection
Base side network
connection
POE over coax
status
Total camera
power budget
GREEN
Blink = no link
On = 100Mbps
On = link
Blink = activity
On = enabled
by Base unit
On = available
5W blink = <5W
ORANGE
Loss of data
n/a
n/a
Approaching
power limit
RED
Severe
Loss of data
10Base-T
(not supported)
Blink = error code
Power limit
exceeded
BNC Connector (for connection to any 75ohm
coaxial cable)
Power Connector Optional (Connect to a Veracity
57V power supply only - in polarity shown)
We, Veracity UK Ltd, of Prestwick International
Aerospace Park, 4 Dow Road, Prestwick, KA9 2TU,
UK declare under our sole responsibility that the
product:
VHW-HWPS-C2 HIGHWIRE Powerstar Duo
is in conformity with the essential requirements
and other relevant requirements of the EMC
Directive (2014/30/EU)
The products are in conformity with the following
standards:
EN 55022:2010
EN 55024:2010
Responsible person:
Alastair McLeod, Group CEO
Issued: 7th Dec 2015, Prestwick,
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limit s are designed to provide reasonable p rotecti on
against harmful interference when the equi pment is ope rated
in a commercial environment.
This equ ipmen t generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
© Veracity UK Ltd 2016 QSGWV1.4 UK
HIGHWIRE POWERSTAR DUO is a trademark of Veracity UK Ltd
CONNECTIONS & LEDS
DECLARATIONS OF
CONFORMITY
Page 2
PRODUCT
DIMENSIONS
| Connect 1-2 cameras or POE / non-POE
devices to the RJ45 ports.
| 57V DC power to the HIGHWIRE Powerstar
Base unit is recommended, giving typically 25
watts of total camera power budget.
APPLICATION DIAGRAM
POE OVER COAX
| Connecting 57V DC power directly to the
Duo unit increases the POE power available
if required.
| The VPSU-57V-800 supply supports 40
watts of total camera power and the VPSU
57V-1500 supports 78 watts.
APPLICATION DIAGRAM
LOCAL POWER SUPPLY
| Total camera power budget using a POE
switch is typically 8 watts (802.3af) or 18
watts (802.3at). Refer to the power budget
table in the datasheet.
Note | The LED indicated power is the total
limit and remains constant.
| No POE is sent over the coax, so a
HIGHWIRE VHW-HW powered by 12V
may be used at the base side.
75 mm
22 mm
POWER
SUPPLY
NETWORK
SWITCH
Ethernet Data Only
VHW-HW VHW-HWPS-C2
12V DC
VPSU-12V-U
Ethernet & POE
VPSU-57V-800
or
VPSU-57V-1500
POWER
SUPPLY
Up to 350M on RG-59 500M on RG-11
Data Only, No POE over COAX
CAMERA
CAMERA
Ethernet & Optional POE
Up to 350M on RG-59 500M on RG-11
VHW-HWPS-B VHW-HWPS-C2
CAMERA
CAMERA
Optional 57V DC Power
(recommended for
maximum power delivery)
VPSU-57V-800
Ethernet & POE
POE over COAX
POWER
SUPPLY
POE NETWORK
SWITCH
75 mm
113.2 mm
131.38 mm
86.1 mm
Loading...