Veracity HIGHWIRE Powerstar Duo Specsheet

EASY TO USE
ETHERNET OVER COAX
DATASHEET
2 PORT ETHERNET & POE OVER COAX
POWERSTAR
DUO
Connect two IP cameras with HIGHWIRE Powerstar Duo over an existing coax cable
HIGHWIRE Powerstar Duo uses existing coax cabling as a reliable Ethernet network connection and is very easy to use and fast to install.
| Re-uses existing coax cable for 2 IP cameras or devices
| Integrated 2-port POE switch (POE Plus with local power option)
| Eliminates separate power cabling with POE-over-Coax™
| Compatible with all HIGHWIRE Powerstar Base units (1, 4 & 8ch)
| Instantly check connection and power level with SafeView™
| Completely automatic connection, no configuration required
| 100BaseTX performance over 300m of RG59 (500m on RG11)
HIGHWIRE Powerstar Duo incorporates a two-port POE switch for IP cameras
HIGHWIRE Powerstar Duo makes the most of your legacy cabling and multiplies its capability by connecting two IP cameras or other network devices
Ethernet Over Coax
HIGHWIRE Powerstar Duo’s unique ultra low-power design and efficient power delivery enables long range Ethernet over coax. It works even over the lowest grade cable, such as the high­resistance, copper-clad steel (CCS) types found in many legacy installations. This means that legacy coax upgrades can be planned with confidence, while a quick check of the SafeView™ power level display reaffirms that the device connections will continue to be reliable, whatever the cable used.
For predictable network operation with no restrictions, HIGHWIRE technology delivers a full 200Mbit/s of bandwidth
POE OVER COAX
Application Diagram
POWER SUPPLY
POE NETWORK
SWITCH
VPSU-57V-800
Optional 57V DC Power
(recommended for maximum
at 300m (1000 ft) of RG-59 or 500m (1600 ft) of RG-11 coax. For full information on POE-over-Coax™ distances achievable, please refer to the Range Table in the HIGHWIRE Powerstar datasheet or on the Veracity website. For POE power budget and power supply options, see the POE Power Budget Table opposite.
measurements and calculations, installing HIGHWIRE Powerstar Duo is simple. The Base end of the coax is driven by single-channel, 4-channel or 8-channel HIGHWIRE Powerstar Base unit. The DUO unit can be powered either by POE over coax, delivering a maximum total POE power budget of 25 watts, or by one of the optional local PSUs, delivering 40 or 78 watts.
HIGHWIRE Powerstar DUO
The DUO variant of HIGHWIRE is designed for the camera end of the coax and, with an integrated two-port POE switch, enables connection of two IP cameras over a single coax. With
HIGHWIRE Powerstar Duo features Veracity’s unique SafeView™ display, to provide IP camera installers with an instant and very easy-to-understand confirmation of correct operation from
either end of the cable. no need to configure IP addresses, set DIP switches, or make awkward
power delivery)
Up to 350M on RG-59 500M on RG-11
POE over COAX
VHW-HWPS- B VHW-HWPS-C2
CAMERA
CAMERA
Ethernet & Optional POE
The diagram shows POE power delivery over coax from the Base end. The Powerstar Base unit may be powered by a POE or POE Plus switch, or for maximum power delivery
Ethernet & POE
over coax, by Veracity’s 57V DC PSU.
See POE Power Budget Table for POE
power outputs.
IMAGINATION | INNOVATION | INTEGRATION DATASHEET
HIGHWIRE Powerstar Duo allows one analogue camera to be replaced with two IP cameras
POE over Coax or Local Power
In the simplest implementation (shown below left) the BASE unit receives power from a standard POE switch or Veracity’s 57V DC PSU and transmits POE over the coax. The DUO unit receives this power and delivers up to 25 watts shared between two IP cameras. No external power cabling is required, and all detection and setup occurs automatically. For higher POE power budgets, an optional Veracity 57V DC PSU may be used to power the DUO locally at the camera end (shown below right) delivering 40 watts or 78 watts depending on PSU model. See POE budget table for details.
POWER SUPPLY TO DUO
Application Diagram
POWER SUPPLY
VPSU-12V-U
12V DC
POE POWER BUDGET TABLE
POE AVAILABLE FROM HIGHWIRE POWERSTAR DUO
PSU LOCATION POWER SUPPLY POE POWER BUDGET
(To IP Cameras)
Base End POE Switch 10W
Base End POE Plus Switch 20W
Base End VPSU-57V-800 25W
Camera End VPSU-57V-800 40W
Camera End VPSU-57V-1500 78W
The table shows the total POE power budget available from the two ports on the HIGHWIRE Powerstar Duo. Note that the maximum power available from
any one port is 25W.
VPSU-57V-800
VPSU-57V-1500
POWER
or
SUPPLY
CAMERA
NETWORK
SWITCH
Ethernet Data Only
Up to 350M on RG-59 500M on RG-11
Data Only, No POE over COAX
VHW-H W VHW-HWPS-C2
The diagram shows power injection at the
Camera end, using a PSU for HIGHWIRE
Powerstar Duo, with no power delivery over
coax. This option allows the maximum POE
power output.
www.veracityglobal.com
CAMERA
Ethernet & POE
ETHERNET OVER COAX
TECHNICAL SPECIFICATION
POWER
Input connector Detachable screw terminal Power input POE OR 57V DC Power consumption 3W - 8W depending on POE load
POE STANDARDS
IEEE 802.3af and IEEE 802.3at compliant
POE POWER OUTPUT
Between 10W and 78W depending on power source (see table) managed across 2 ports. Max 25 watts per port (POE Plus)
HIGHWIRE INTERFACE
Connector type BNC 75ohm Cable type 75ohm coax cable (RG59, RG6, RG11 or similar) Range Up to 300m on RG59, 350m on RG6, 500m on RG11, all at full rate Bandwidth 200Mbps (total up + down)
ETHERNET INTERFACE
Connector type RJ45 x 2, unmanaged 10/100 switch Rates 10BASE-T or 100BASE-TX and full duplex, auto configuring Cable type Straight through or cross-over Cat 5, Cat 5e or Cat 6 patch
LED INDICATORS
RJ45 Yellow Network link and activity RJ45 Green POE status (on/off) Coax Status Coax link, Base network link, coax power (POE) POE Power Power budget (in steps of 5W)
POWERSTAR
DUO
PHYSICAL/ENVIRONMENTAL
Dimensions L 132mm (inc. BNC) W 75mm H 22mm (W 94.6mm with wall mount lugs) Mounting 4mm mounting holes on 86.1mm centres Weight 179g [6.3oz] (183g with wall mount brackets) [6.4oz] Operating temperature -10ºC to 50ºC [14ºF to 122ºF] Relative humidity 85% non-condensing Compliance CE, FCC, RoHS
PRODUCT CODES
VHW-HWPS-C2 HIGHWIRE Powerstar Duo Ethernet over coax camera unit with integrated 2-port POE switch VHW-HWPS-C4 HIGHWIRE Powerstar Quad Ethernet over coax camera unit with integrated 4-port POE switch VHW-HWPS-B HIGHWIRE Powerstar Base Single-port Ethernet over coax base unit VHW-HWPS-B4 HIGHWIRE Powerstar Base 4 Four-port Ethernet over coax base unit VHW-HWPS-B8 HIGHWIRE Powerstar Base 8 Eight-port Ethernet over coax base unit VPSU-57V-800 57V DC 800mA PSU Optional 40 watt PSU for Quad /Duo VPSU-57V-1500 57V DC 1500mA PSU Optional 78 watt PSU for Quad /Duo VHW-HW HIGHWIRE Ethernet over coax cable adaptor VPSU-12V-U 12V DC Power Supply PSU for standard HIGHWIRE VHW-HW
EMEA Sales
Veracity UK Ltd Prestwick International Aerospace Park 4 Dow Road Prestwick KA9 2TU UK Tel +44 (0) 1292 264967 Fax +44 (0) 845 528 1081 www.veracityglobal.com sales@veracityuk.com
HIGHWIRE POWERSTAR QUAD is also available with 4-port POE switch
© Veracity UK Ltd 2016 WV1.0 UK
HIGHWIRE POWERSTAR DUO and HIGHWIRE POWERSTAR QUAD, HIGHWIRE POWERSTAR BASE 4 AND 8 are trademarks of Veracity UK Ltd
Americas Sales
Veracity USA Inc. Tel: 1-800-679-1590 Fax: 1-800-679-0714 www.veracityglobal.com sales@veracityusa.com
Loading...