Page 1
LOW VOLTAGE 802.3AT POE SWITCH
QUICK START GUIDE
We, Veracity UK Ltd. of Prestwick International Aerospace Park, 4 Dow Road, Prestwick,
KA9 2TU, United Kingdom, declare under our sole responsibility that the products
VCS-4P1-Mob (CAMSWITCH 4 Mobile)
VCS-8P2-Mob (CAMSWITCH 8 Mobile)
are in conformity with the essential requirements and other relevant requirements
of the EMC Directive (2004/108/EC)
The products are in conformity with the following standards:
EN 55022:2010
EN 55024:2010
Responsible Person Mr Alastair McLeod, Managing Director
Issued 8
th
August 2013 at Prestwick.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1)this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digit al device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable pro tection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with t he instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a r esidential area is likely to cause harmful
interference in which case the user will be required t o correct the interference at his own expense.
NETWORK SWITCH
/ MOBILE NVR
POWER
12/24V DC
VCS-4P1-MOB
VCS-8P2-MOB
ALL CABLES UP TO 100M
CAT 5e OR BETTER
ETHERNET WITH POE ETHERNET DATA ONLY
UP TO 4 OR 8 POE OR
NON-POE DEVICES
NVR
APPLICATION DIAGRAM
CAMSWITCH Mobile delivers a network connection and optional
POE to 4 or 8 cameras. POE is converted to IEEE 802.3af /
802.3at levels from a 12V or 24V DC supply.
CONNECTIONS
All ports support 10/100 Base-T with auto-negotiation
and auto-crossover.
4 or 8 network ports with 802.3at POE
1 or 2 data-only ports
12V DC / 24V DC Power Input
Port LEDs : Green POE enabled (POE ports),
Power good (non-POE ports)
Yellow Ethernet Link /Activity
+
_
WALL MOUNTING CLIPS
The enclosed mounting clips can be clipped where required
along the side of the unit to permit surface mounting.
Up to M5 screws can be used at 122mm separation.
See the drawing drill template overleaf.
Consult the power chart if ventilation is restricted.
• Allportssupport10/100Base-TEthernetwithauto-negotiation
and auto-crossover.
• POEisautomaticallydetectedandenabledtocompliantdevices.
• POEisdeliveredontheEthernetdatapairsforcompatabilit ywith
4-pin external connectors (e.g. M12). Cables should be secured
appropriately to prevent vibration.
VCS-4P1-Mob | CAMSWITCH 4 Mobile
VCS-8P2-Mob | CAMSWITCH 8 Mobile
1. Insert 2. Click
Page 2
DIMENSIONS | MOUNTING HOLE TEMPLATE
Width 110mm
(131mm inc. clips)
Depth 108mm
(inc. DC connector)
Height 40mm
Weight VCS-4P1-Mob 290g
VCS-8P2-Mob 350g
Scale 1:1
POWER BUDGET
CAMSWITCH Mobile can deliver up to 80 watts of total camera
power at its rated ambient temperature of 50°C.
To calculate the power budget required, add up the power draw
in watts of all POE devices, as given in their datasheets. (Power
classes are not used, and cable losses are already accounted for.)
Note that the enclosure may become hot in operation. Restricted access
to the product is recommended.
The graph opposite shows the approximate temperature rise
with moderate ventilation. Note that restricted ventilation and space
can lead to signifi cantly increased ambient temperature.
If the input voltage drops below 12V (for example during engine
cranking) the power budget should be reduced as shown on the
graph, down to 50 watts at the minimum 8.5V DC input
Power Budget 80W 60W 40W 20W No POE
Fuse Rating (12V) 10A 7.5A 5A 3A 2A
Fuse Rating (24V) 5A 4A 3A 2A 2A
POWER CONNECTIONS
CAMSWITCH Mobile can operate from an 8.5V to 40V DC
supply, and steps this up to a steady POE voltage internally.
(For AC applications, contact Veracity.)
The power supply or battery and wiring must be appropriately
rated and fused for the current required. Recommended fuse
ratings (slow blow type) are:
131
102
122
110
5
8
25
Note that the POE voltage is not isolated from the DC supply. CAMSWITCH
Mobile is intended for use with IEEE-compliant (individually isolated) POE
and Ethernet devices within a closed system.
FUSE
VCS-4P1-MOB
VCS-8P2-MOB
8.5 12 24 40
40
50
60
70
80
INPUT VOLTAGE
(VOLTS DC)
OUTPUT POWER
(WATTS)
30º above ambient
20º above ambient
Loading...