Venturer PVS6370 User Manual

Portable DVD
Player

Owner’s Manual

PVS6370

SAFETY PRECAUTIONS

WARNING: T O REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMO VE
COVER (OR BACK). NO USER­SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

The lightning flash with an arrowhead
symbol, within the equilateral
triangle, is intended to alert the user

to the presence of uninsulated
"dangerous voltage" within the product's
enclosure that may be of sufficient magnitude
to cause an electric shock.

The exclamation point within the
equilateral triangle is intended to alert

the user to the presence of important
operating and maintenance (servicing)
instructions in this owner's manual.

* SEE REAR OF UNIT FOR GRAPHIC

SYMBOLS *

This product
contains a low
power laser
device.

On Placement

• Do not use the unit in places that are

extremely hot, cold, dusty, or humid.

• Do not restrict the air flow of the unit by

placing it in a place with poor air flow, by
covering it with a cloth, or by placing it on
carpeting.

FCC Information

WARNING: Changes or modifications to this
unit not expressly approved by the party
responsible for compliance could void the
user authority to operate the equipment.
NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation. This
equipment, used in accordance with the
instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user is
encouraged to try to correct the interference
by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the
receiver is connected.

• Consult the dealer or an experienced radio/

TV technician for help.
Shielded cables must be used with this unit to
ensure compliance with the Class FCC limits.

WARNING: TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE. DO NOT PLACE
OBJECTS FILLED WITH LIQUIDS ON
OR NEAR THIS UNIT.

CAUTION: Use of controls or adjustments or
performance of procedures other than those
specified may result in hazardous radiation
exposure.
CAUTION: D ANGER OF EXPLOSION IF BATTER Y
IS INCORRECTLY REPLACED. REPLACE ONLY
WITH THE SAME OR EQUIVALENT TYPE.

CAUTION

INVISIBLE LASER RADIATION EMITTED

WHEN OPENED AND INTERLOCKS

DEFEATED.

AVOID EXPOSURE TO BEAM.

On Safety

• When connecting or disconnecting the AC
cord, grip the plug and not the cord itself.
Pulling the cord may damage it and create
a hazard.

• When you are not going to use the unit for a
long time, disconnect the power adapter.

On Condensation

• When left in a heated room where it is warm
and damp, water droplets or condensation
may form inside the unit. When there is
condensation inside the unit, the unit may
not function normally. Let the unit stand for
1 to 2 hours before turning the power on, or
gradually heat the room and let the unit dry
before use.

Rating Plate Location

• The rating plate location is on the rear of
the unit.

WARNING: Should any trouble
occur, disconnect the car power
adapter and refer servicing to a
qualified technician.

Notes on Copyright

It is forbidden by law to copy, broadcast, show,
broadcast on cable, play in public, or rent
copyrighted material without permission.
Apparatus Claims of U.S. Patent Nos.
4,907,093; 5,315,448; and 6,516,132 licensed
for limited viewing uses only.
This product incorporates copyright protection
technology that is protected by U.S. patents and
other intellectual property rights. Use of this
copyright protection technology must be
authorized by Macrovision, and is intended for
home and other limited viewing uses only
unless otherwise authorized by Macrovision.
Reverse engineering or disassembly is
prohibited.

ACCESSORIES

Please check and identify the supplied accessories.

• To order accessories please visit http://www.1800customersupport.com

Remote Control (with battery) .......................................................................................x 1

Car Power Adapter .......................................................................................................x 1

Mounting Strap ............................................................................................................. x 1

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings.
Install in accordance with the manufacturer’s
instructions.

8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.

9. Do not defeat the safety purpose of the polarized
or grounding - type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong is provided for your safety. If the provided
plug does not fit into your AC power outlet,
consult an electrician for replacement of the
obsolete outlet.

DISC FORMATS

The unit can playback discs bearing any of the following marks:

DVDs
[8cm(3")/12cm(5") disc]

Region Management Information

This unit is designed and manufactured to
respond to the Region Management Information
that is encoded on DVDs. If the region number
printed on the DVD does not correspond to the
region number of this unit, this unit cannot play
that disc.
The region number of this unit is 1.

Disc Function or Operation that is
Not Available

When the symbol appears on the TV screen,
it indicates that the function or operation
attempted is not available at that time. This
occurs because the DVD manufacturer
determines the specific functions. Certain
functions may not be available on some discs.
Be sure to read the documentation provided with
the disc.

Title, Chapter and Tracks

• DVDs are divided into “titles” and “chapters”. If the
disc has more than one movie on it, each movie
would be a separate “title”. “Chapters” are sections
of titles.

• Audio CDs are divided into “tracks”. A “track” is
usually one song on an Audio CD.

Note:
Numbers identify each title, chapter, and tra ck on a disc. Most discs hav e these numbers recorded
on them, but some do not.

REMOTE CONTROL

Using the Remote Control

• Point the remote control at the REMOTE
SENSOR located on the unit.

• When there is a strong ambient light source,
the performance of the infrared REMOTE
SENSOR may be degraded, causing
unreliable operation.

• The recommended effective distance for
remote operation is about 16 feet (5 meters).

To Change Remote Battery

1. Open the battery door.

2. Insert one CR2025 (3V) size battery.

CAUTION:
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type.

DO NOT RETURN THIS PRODUCT TO THE STORE.

Please visit online help at http://www.1800customersupport.com

Need More Help?

10.Protect the AC power cord from being walk ed on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.

11.Only use attachments/accessories specified by
the manufacturer.

12.Use only with a cart, stand, tripod, bracket, or
table specified by the manufacturer,
or sold with the apparatus. When a
cart is used, use caution when
moving the cart/apparatus
combination to avoid injury from tip­over.

13.Unplug this apparatus during lightning storms or
when unused for long periods of time.

14.Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as the power­supply cord or plug is damaged, liquid has spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.

Audio CDs
[8cm(3")12cm(5") disc]

Icons Used on DVDs

Sample lcons

Language selections for audio
Language selections for subtitles
Screen aspect ratio
Multiple camera angles
Region code indicator

Note:
When playing back a CD-G (Graphics) or CD
EXTRA disc, the audio portion will be played,
but the graphic images will not be shown.

Notes on Unauthorized Discs

You may not be able to play back some DVDs
on this unit if they were purchased from outside
your geographic area or made for business
purposes.

Take out the PVC
sheet before
operating the
Remote Control.

Battery Replacement

When battery becomes weak, the operating
distance of the remote control will greatly
reduced and you will need to replace the
battery.
Notes:

• If the remote control is not to be used for a
long time, remove the battery to avoid
damage caused by battery leakage
corrosion.

• When discarding batteries, environmental
problems must be considered and local rules
or laws governing the disposal of these
batteries must be followed strictly.

WARNING:

• Do not dispose of battery in fire, battery may
explode or leak.

• The battery shall not be exposed to
excessive heat such as sunshine, fire or the
like.

CONTROL REFERENCE GUIDE

1) OPEN Button
Press the
front panel to open the disc door.

2)
Performs fast rev erse pla ybac k.

3)
Performs fast f orward playback.

4) PREV Button
Goes backwards to previous chapters/
tracks.

5)
Advances chapters/tracks.

6) * CHARGING Indicator

7) *
/ ON Switch

8) POWER ON Indicator
When the ST ANDBY / ON s witch is in the
ON position, the green light will illuminate.

PLAY Button

9)
Starts or resumes playback of a disc.

PAUSE Button

10)
Pauses playback and frame advance.

11) STOP Button
Stops playing a disc.

12) Headphone Jack

Remote Control

1) TV MODE button
Adjusts Brightness, Contrast, Color or
View Mode of the LCD screen.

2)
Moves back through titles, chapters or
tracks on a disc.

/ SEARCH buttons

3)

SEARCH: F ast reverse playback.
SEARCH: Fast forward playback.

4) GOTO button
Skips directly to a location on a DVD.

5) Cursor (
Use to move between selections on a
menu screen and adjust certain settings.
ENTER button
Confirms selections on a menu screen.

6) MEMORY button
In STOP mode, sets titles/chapters in a
favourite order.

7) Number (0 - 9) buttons
Use when creating programs, entering
parental control password or locating a
title/chapter/track or specific time.

8) REPEAT A-B button
Performs point-to-point repeat playback on
a DVD or CD.
REPEAT DISC button
Repeats a DVD chapter or title.
Repeats a CD track or the entire disc.
SETUP button
When a DVD is stopped, brings up the
unit’s SETUP menu.

9) SUBTITLE button
Selects one of the subtitle languages
programmed on a DVD (if available).
RETURN button
Returns to normal operation after using
the SETUP menu of a DVD.

OPEN button and hold the
SEARCH
SEARCH Button

NEXT Button

(CHARGE) / STANDBY(power off)

PREV button

, , , )a buttons

13) VOLUME Control
Adjusts the volume.

14) AUDIO / VIDEO OUT Jacks

15) DC IN 9V-12V Jack

16) Remote Sensor
Receives the remote control signal.

17) LCD Screen

* If you have purchased a RECHARGEABLE
BATTERY for this unit, slide to
red CHARGING Indicator will be lit while your
are charging up the battery. To order this
battery or to get more information about this,
visit www.1800customersupport.com.

10) AUDIO button
Selects one of the audio sound tracks on
a DVD (if more than one is available) or
select the audio output mode on a CD.

11) ANGLE button
Switches between multiple camera angles
when the DVD you are playing has been
programmed with multiple camera angles.

12) DISPLAY button
Shows status information on the screen.

STOP button

13)
Stops playing a disc.

PLAY button

Starts or resumes playback of a disc.

PAUSE button

Pause playback and frame advance.

14) NEXT button
Moves forw ard through titles, chapters or
tracks on a disc.

15) MENU button
Enters and exits the main DVD menu.

MAINTENANCE

Cleaning a Disc

A defective or soiled disc inserted into the unit
can cause sound to drop out during playback.
Handle the disc by holding its inner and outer
edges.

• Do NOT touch the surface of the unlabeled
side of the disc.

• Do NOT stick paper or tape on the surface.

• Do NOT expose the disc to direct sunlight
or excessive heat.

• Clean the disc before playback. Wipe the
disc from the
center outward
with a cleaning
cloth.

• NEVER use
solvents such as
benzine or alcohol to clean the disc.

• Do NOT use irregular shaped discs
(example: heart shaped, octagonal, etc.).
They may cause malfunctions.

Cleaning the Unit

• Be sure to turn the unit off and disconnect
the car power adapter before maintaining
the unit.

• Wipe the unit with a dry soft cloth. If the
surfaces are extremely dirty , wipe clean with
a cloth that has been dipped in a weak soap­and-water solution and wrung out
thoroughly. Then wipe with a dry cloth.

• Never use alcohol, benzine, thinner,
cleaning fluid or other chemicals. Do NOT
use compressed air to remove dust.

Important Note

• Before transporting the unit, remove any disc
from the disc compartment.

UNIT OPERATION

Turning on the Unit

1. Slide the (CHARGE) / STANDBY / ON switch on the unit to the
ON position.

2. The DVD logo (start-up picture) will appear on the screen.

3. After use, slide the
unit to STANDBY (power off) position.

(CHARGE) / STANDBY / ON switch on the

and a

POWER SUPPLY

Using the Car Power Adapter

The included 12V car power adapter is designed
for use with vehicles that have a 12V, negative
ground electrical system.

Disconnect this car power adapter when

not in use. Not for use in 24V vehicles.

any other equipment.

• In the interest of traffic safety, drivers should not operate the unit or vie w videos while driving.

• When the inside of the 12V car socket is dirty with ashes or dust, the plug section may become
hot due to poor contact. Be sure to clean the 12V car socket before use.

• After use, disconnect the 12V car power adapter from both the unit and cigarette lighter socket.

• If the unit is not properly attached to a vehicle, it may become airborne in the event of an
accident and cause damage, injury, or death.

• Check your local traffic laws for rules governing the use of video devices in vehicles.

WARNING:

CAUTION:

For continued protection
against risk of fire, replace only
with same type and rating of
fuse.

Cautions:

• Use this unit only with the included 12V car power adapter. Use with other car adapters
could damage the unit, or even your vehicle.

• The included 12V car power adapter is for use with this unit only. Do not use it with

CONNECTIONS

A. Connecting a TV

If your TV has Audio/Video inputs, you can connect
the unit to your TV using a standard A/ V cable (not
included).

Watching a DVD on your TV

1. Turn on the unit.

2. T urn on the TV and follow the instructions included
with it to play the DVD.

Notes:

• Make sure to use the correct Audio/Video cable. Connecting the plugs incorrectly ma y cause
a weak signal.

• If your TV does not have Audio/Video inputs, y ou will need to purchase an RF modulator (sold
separately) and follow the instructions included with it to connect the unit to your TV.

B. Using Headphones (not included)

Tur n down the volume before connecting the
headphones/earphones. Slowly raise the volume with
the headphones on until you reach your desired
volume. When headphones are connected, the
speaker is automatically disabled.

Caution:
Avoid listening to sound at excessive levels which
could be harmful to your ears.

PLACEMENT

A. Mounting in the Vehicle

Use the supplied mounting strap to install the unit
on the back of the vehicle's headrests. Tightly
wrap the mounting strap around the headrest.

SAFETY WARNING!

• This unit should never be used by the vehicle's driver or left unsecured in the

• If this unit is being used in your vehicle, be sure that it is secured or held safely , and does

• All passengers should wear seat belts when using this unit in a moving vehicle.

• If in doubt, please contact your vehicle manufacturer for further advice.

vehicle while driving.

not obstruct any safety device, including air bags or seat belts.

B. Using the Stand

Y ou can stand the unit up on a desk or tab le
using the stand on the back.

SOUND SYSTEM

Dolby Digital

Dolby Digital is a technology developed by Dolby Laboratories. Soundtracks encoded in Dolby
Digital can reproduce from one to 5.1 discrete channels of excellent quality audio.
The unit automatically recognizes the Dolby Digital bitstream and provides a downmix suitable
for two-channel listening. An additional Dolby Digital decoder is required for reproduction of the
discrete multi-channel soundtracks available on many DVDs.
Manufactured under license from Dolby Laboratories.

'Dolby' and the double-D symbol are trademarks of Dolby Laboratories.

PLAYING A DISC

This owner’s manual explains the basic instructions for operating this unit. Some
DVDs are produced in a manner that allows specific or limited operation during
playback. Therefore, this unit may not respond to all operating commands. THIS IS
NOT A DEFECT. Please refer to the instructions accompanying the specific DVD in
question for more information about the options available on that DVD.

” may appear on the screen during operation. A “ ” means that the desired

“
operation is not permitted by the unit or disc.

Playing a Disc

1. Slide the (CHARGE) / ST ANDBY / ON
switch to the ON position.
See CUSTOMIZING THE FUNCTION
SETTINGS before proceeding to step 2.

2. Press the
button and hold the
front panel to open
the disc door.

3. Hold the disc by its
sides and gently push
it onto the spindle with
label side facing towards you until you hear
a “click”.

4. Gently push the disc door closed. It takes a
short while for your unit to load the disc. After
loading, for most DVDs, the unit will
automatically take you main menu or start
playing. If the unit does not automatically start
playing the D VD , press the

OPEN

PLAY button.

Pausing Playback (Still Mode)

Press the PAUSE button. To resume normal
playback, press the
Each time you press the
picture advances one frame.

PLAY button.

PAUSE button, the

Stopping Playback

Press the STOP button at the location where
you want to interrupt playback. To resume
playback at the position where the disc was
stopped, press the
If you press the
memory will be cleared and pressing the
PLA Y b utton will reset the disc to the beginning.

PLAY button.

STOP button twice, the unit’s

Fast Forward / Fast Reverse

1. Press the SEARCH or SEARCH
button when a disc is playing. Each time you
press the SEARCH or SEARCH
button, the playback speed changes in the
following sequence:

2. Press the
the desired point to resume normal playback.

Notes:

• The DVD player mutes sound and subtitles
during reverse and forward scan of DVDs.

• The fast playback speed may differ
depending on the disc.

PLAY button when you reach

Skip (Forward / Reverse)

• Press the PREV button to go back to
current or previous chapters/tracks.

• Press the NEXT button to advance
chapters/tracks.

• For audio CDs, use the number buttons on
the remote control to jump immediately to the
desired track number.

Audio Selection

On some DVDs, the sound is recorded in two or
more formats. Follow the directions below to
select the preferred
language and sound
system.

1. While a disc is playing, press the AUDIO
button to show the current audio format
number.

2. Press the AUDIO button repeatedly to select
the desired audio format.

Notes:

• If only one audio format is recorded on the
DVD, the number does not change.

• Some DVDs allow you to change audio
selections only via the disc menu. If this is
the case, press the MENU button and choose
the appropriate language on the disc menu.

• You can select different audio channels
(Stereo, Left or Right) on an Audio CD by
pressing the AUDIO button repeatedly.

Subtitle Selection

1. While a DVD is playing, press the SUBTITLE
button to display the current
language setting, as shown in
the example.

2. Press the SUBTITLE button repeatedly to
select the desired subtitle language. You can
turn subtitles off by pressing the SUBTITLE
button repeatedly until the “
displayed.

Notes:

• Some DVDs are set to display subtitles
automatically , and you cannot turn them off
even if you set the subtitle function to off.

• During some scenes, the subtitles may not
appear immediately after you select your
desired scene.

• The number of subtitle languages recorded
differs depending on the disc. If only one
language is recorded, the language does
not change.

• This function can only be used for discs on
which subtitles have been recorded in
multiple languages.

• Some DVDs allow you to change subtitles
only via the disc menu. If this is the case,
press the MENU button and choose the
appropriate subtitle on the disc menu.

Off

Angle Selection

Some DVDs contain scenes which have
been shot from a number of different angles.
For these discs, the same scene can be
viewed from each of these different angles.

1. While you are playing a DVD with different
angles recorded, press the ANGLE button
to view the number of current angles
available.

2. Press the ANGLE button repeatedly to
change the scene to the next recorded
angle.

• After approximately two seconds, playback
will continue from the new angle you
selected.

• If no button is pressed within 10 seconds,
playback continues without changing the
current angle.

Notes:

• This function can only be used for discs on
which scenes shot from multiple angles
have been recorded.

• If only one angle is recorded, “

Sequence of angle shots

(Example)

displayed.

1/1

Display Function

While the disc is playing, press the DISPLAY
button repeatedly to display information on
operation status.

Elapsed Time:

Elapsed time from the beginning of the title
which is currently playing.

Remain Time:

Remaining time of the title which is currently
playing.

Adjust the LCD Screen

You can adjust brightness, contrast, color or
view mode of the LCD screen.

1. Press the TV MODE button.

2. Press the
Contrast, Color or View Mode.

3. Then press the
setting. (For View Mode, press the ENTER
button to change the setting.)

4. Press the TV MODE button to exit the menu.

/ button to select Brightness,

/ button to change the

” is

” is

LOCATING A DESIRED SECTION

Locating a Specific Title

If a DVD contains title numbers, you can locate
a specific title by directly selecting its title
number.

1. Press the GOTO button.

2. Press the corresponding number button(s)
for the title you want.

3. Press the ENTER button to confirm.
Playback starts from the selected section.

Notes:

• If the title numbers you entered is not
permited by the DVD, after you press the
ENTER button, it will restore to - - -. You
should re-enter correct numbers.

• Some discs may not respond to this process.

• This method of locating a title is available
only on a DVD that contains title numbers.

Locating a Specific Chapter

If you know the chapter number for the chapter
that you want to play , you can locate it b y directly
selecting that number.

1. Press the GOTO button.

2. Press or button to display Chapter and
press the corresponding number button(s)
for the chapter you want.

3. Press the ENTER button to confirm.
Playback starts from the selected section.

Notes:

• If the chapter numbers you entered is not

permited by the DVD, after you press the
ENTER button, it will restore to - - -. You
should re-enter correct numbers.

• Some discs may not respond to this
process.

• This method of locating a chapter is
available only on a DVD that contains
chapter numbers.

Locating a Specific Time

Y ou can mov e to a specific location by entering
its corresponding time (hours, minutes,
seconds).

1. Press the GOTO button.

2. Press

3. Press the ENTER button to confirm.

Notes:

• If the time numbers you entered is not

• Some discs may not respond to this

• Some scenes may not be located as

• This method for accessing specific locations

or button to display Time and
press the corresponding number buttons for
the setting point you want.

Playback starts from the selected section.

permited by the DVD, after you press the
ENTER button, it will restore to - - : - - : - .
You should re-enter correct numbers.

process.
precisely as you specified.
is available only within the current title of

the DVD.

REPEA T PLAYBA CK

Y ou can pla y a specific title or chapter repeatedly. (Title repeat, chapter repeat, A-B repeat)

Repeating a Chapter

1. While the DVD is playing, press the
REPEAT DISC button until the

Repeat Chapter

“
screen. The current chapter is played
repeatedly.

” indicator displays on the

Repeating a Title

2. While the DVD is playing, press the
REPEAT DISC button until the
“

Repeat Title

screen. The current title is pla yed repeatedly .

” indicator displays on the

To Resume Normal Playback

3. While the DVD is playing, press the
REPEAT DISC button until the
“

Repeat Off

screen.

You can play a single track or the whole disc
repeatedly.

” indicator displays on the

Repeating a Single Track

1. While the CD disc is playing, press the
REPEAT DISC button until the “

Repeat single

screen. The current track is played
repeatedly.

” indicator displays on the

Repeating a Whole Disc

2. While the CD disc is playing, press the
REPEAT DISC b utton until the “
” indicator displays on the screen. The whole
disc is played repeatedly.

Repeat all

To Resume Normal Playback

3. Press the REPEAT DISC button until the “

Repeat off

screen.

” indicator displays on the

Repeating a Specific Section

You can play a specific section repeatedly.

1. While the disc is playing, press the REPEAT
A-B button at the beginning of the section
(“
repeatedly.

2. Press the REPEAT A-B button again at the
end of the section (“
displayed).

3. The Unit will immediately begin replaying
your selection.

” is displayed) y ou want to pla y

Rep A-

Rep A-B

” is

To Resume Normal Playback

4. While the disc is playing, press the REPEAT
A-B button until the “

indicator displays on the screen.

Note:

• Some discs may not permit A-B repeat
operation.

• You cannot set the A-B repeat function for a
segment that includes multiple camera angles.

• You can specify a segment only within the
current title or track.

• There may be a slight difference betw een point
A and the location where playback actually
resumes depending on the disc.

RepA-B Off

”

DVD PROGRAMMABLE MEMORY

Playing TItles/Chapters in a Favourite Order

Y ou can combine your f avourite titles/chapters and play them
in the order you determine.

1. When a D VD is stopped, press the MEMORY button, the
following display appears.

2. Select the items in the order you want by pressing the
number buttons.
Each time you press the Cursor buttons (
the space is highlighted. Highlight where you w ant to enter,
then press the corresponding number buttons.

3. Press the Cursor buttons (
press the ENTER button. The DVD player starts memory playback.

4. To resume normal playback from memory playback
a) Press the MEMORY button in stop mode.
b) Press the Cursor buttons (

press the ENTER button. All the input programs will be cleared.

c) Press the PLAY button to resume normal playback.

Notes:

• If the title or chapter numbers you entered is not permited by the DVD, after you press the
ENTER button, it will restore to - - -. You should re-enter correct numbers.

• Some discs may not permit memory playback operation.

• If you select repeat during memory playback, the DVD player repeats the current memory
playback.

• If you press the MEMORY button while the display appears on the TV screen, the display disappears.

• The programmed selections will be cleared when you open the disc tray or turn off the DVD play er.

, , , ) to move the highlighted bar to Play Memory, then

, , , ) to move the highlighted bar to “Clear All”, then

, , , ),

VIEWING JPG FILES

This unit can play JPG files recorded on a CD-R or CD-ROM disc (CD-RW is not recommendable).

Viewing JPG Files

1. Open the disc door.

2. Hold a JPG file disc by its edge and gently push it onto the
spindle with the label side facing up until you hear a “click”.

3. Close the disc door. A list of folders/files will appear on the
screen.

4. Press the
picture will appear at the lower right corner. Press the
button to start playback. Press the
list.

Notes:

• Y ou can press the
playback.

• You can press the STOP button to quit playback.

• You can press the

• You can press the ANGLE button to rotate direction of the picture by 90

• Some discs may not permit this operation.

or button to select your desired file, the selected

button to display a folder

P A USE button to interrupt playback. Press the PLAY b utton to resume

PREV or NEXT button to change the picture.

PLA Y

o

.

PLAY MODES FOR CD OR JPEG DISC

Play Modes for CD or JPG Disc

When play CD / JPG discs, you can modify the Play Modes through the Toolkit which appears on
the right of below picture on the screen. Press the
and the
Then press the ENTER button.

1. In Stop mode, press the Cursor buttons ( , , , ) to select

2. Use the Cursor buttons (

3. Select "Add to program", then press the ENTER button. " "

4. Select "Program view" to view programmed files. To add more files by "Browser view" follow

5. Press the

The Toolkit has the following play mode items:

• Repeat ( Off / Single / All ):

• Mode ( Normal / Shuffle / Music intro ):

• Edit mode: Program operation works only when "Edit mode" is selected.

• Program view: To view tracks/files in the "Program view" list. It is disab led when the "Program

• Add to program: Add files/tracks to the "Program view" list. It is disabled if the "Edit mode" is

• Browser view: To view files/tracks in the original view list.

• Clear program: Delete the files/tracks in the "Program view" list.

Note: The program will be deleted if the
opened, or selected files are deleted by selecting "Clear program".

/ button to select files/tracks or play mode items.

"Edit mode" then press the ENTER button.
on the left hand side of the window. Press the ENTER button

to confirm the selected tracks/files. " " will appear in front of
the selected tracks/files.

will disappear from the screen. It means that the trac ks/files you ha ve selected are added into
the "Program view".

above steps.

Off: Resumes normal playback.
Single: Repeats the current track/file.
All: Repeats all files on the current folder or all tracks on the disc.

Normal: Resumes normal playback.
Shuffle: Playbacks track/file in random order.
Music intro (for Audio CD only): Only playbacks the first 10 seconds of all the tracks on the

current folder/disc.

view" list is empty.
not selected.

Select a file/track or more you want to delete in complete stop mode (press the
button twice). "
press the ENTER button. It is disabled if the "Edit mode" is not selected.

PLAY button to start the program playback.

, , , ) to select tracks/files sho wn

" will appear beside the deleted file/track. Select "Clear program" and then

/ button to navigate between the windo ws

STOP

STOP button is pressed twice, the disc door is

TROUBLESHOOTING GUIDE

SYMPTOM CAUSE (AND REMEDY)

No power.
Very little or no sound

is coming from a DVD .

No picture.

The picture is not clear.

Loud hum or noise is
heard.

The disc does not play .

Specifications and external appearance are subject to change without notice.

• Ensure the car power adapter is connected.

• Make sure that the unit is turned on.

• Make sure that you select ON mode.

• Make sure the unit is not paused. Press the

• Make sure the unit is not in fast-forward or fast-re v erse mode. Press
the PLAY button.

• Make sure the AUDIO/VIDEO input/output connections are correct.

• The DTS DVD cannot be decoded to have speaker output.

• The unit has overheated. Shut it off for 30 minutes to allow it to cool
down.

• The region number of the disc doesn't match the region number of
this unit.

• The DVD is dirty. Gently clean the disc.

• The disc is scratched.

• Please adjust the LCD's brightness, contrast and color using the TV
MODE button on the remote control.

• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened
with alcohol.

• Clean the disc.

• There is no disc inside the unit ("No Disc" appears on the screen).

• Insert the disc correctly with the graphics facing up.

• Clean the disc.

• A non-NTSC disc has been inserted, or the disc region number does
not match the region number of the unit.

• Condensation may have formed inside the unit due to a sudden
change in temperature. Wait about an hour for it to clear and try again.

PLAY button.

CUSTOMIZING THE FUNCTION SETTINGS

Language

OSD Language

1. Press the SETUP button in stop mode.

2. Press the

3. Press the ENTER button, then the
change the Language.

4. Press the ENTER button.

5. Press the SETUP or RETURN button to exit the menu.

Subtitle

1. Press the SETUP button in stop mode.

2. Press the

3. Press the ENTER button, then the
change the Language.

4. Press the ENTER button.

5. Press the SETUP or RETURN button to exit the menu.

Notes:

• Some DVDs may be set to display subtitles in a language other than the one you selected. A
prior subtitle language may be programmed on the disc.

• Some DVDs allow you to change subtitle selections only via the disc menu. If this is the case,
press the MENU button and choose the appropriate subtitle language from the selection on
the disc menu.

Audio

1. Press the SETUP button in stop mode.

2. Press the

3. Press the ENTER button, then the
preferred Audio is displayed.

4. Press the ENTER button.

5. Press the SETUP or RETURN button to exit the menu.

Note: Some DVDs may not play in the language you selected. A prior language may be
programmed on the disc.

DVD Menu

1. Press the SETUP button in stop mode.

2. Press the

3. Press the ENTER button, then the
preferred DVD Menu language is displayed.

4. Press the ENTER button.

5. Press the SETUP or RETURN button to exit the menu.

Note: Some DVDs may not include your pre-selected language. In this case, the DVD player
automatically displays disc menus consistent with the disc's initial language setting.

Video

Aspect Ratio

1. Press the SETUP button in stop mode.

2. Press the

3. Press the

4. Press the ENTER button, then the
change the aspect ratio.

5. Press the ENTER button.

6. Press the SETUP or RETURN button to exit the menu.

Notes:

• The displayable picture size is preset on the DVD. Therefore, the playback picture of some
DVDs ma y not conf orm to the picture size you select.

• When you play DVDs recorded in the 4:3 picture size only , the pla yback picture always appears
in the 4:3 picture size regardless of the Aspect Ratio setting.

• Select 16:9 to conform the LCD screen on the unit. Always be sure that your Aspect Ratio
conforms to the actual TV in use if you connect the unit to a TV.

View Mode

1. Press the SETUP button in stop mode.

2. Press the

3. Press the

4. Press the ENTER button, then the
change the View Mode.

5. Press the ENTER button.

6. Press the SETUP or RETURN button to exit the menu.

Fill Fill the screen with decoded image.
Original Display image as it’s original size.
Auto Fit Automatically fit the decoded image on screen without distortion. Black bars will be

Pan Scan Select when a standard 4:3 TV is connected. Displays pictures cropped to fill your

Note: Depending on the DVDs, you may not be able to view the mode as selected.

Misc

Use Default Settings

1. Press the SETUP button in stop mode.

2. Press the

3. Press the
Default Settings” dialogue box.

4. Press the ENTER button then press the / button to select
“Yes”. Press the ENTER button. The or iginal setting will be
restored. The unit will exit setting menu automatically and re­load the disc in the disc tray.

Note: It will take 3-5 seconds to reset the DVD player to the factory default.

Screen Saver

1. Press the SETUP button in stop mode.

2. Press the

3. Press the
Saver.

4. Press the ENTER button, then press the / button to change
the On/Off mode.

5. Press the ENTER button.

6. Press the SETUP or RETURN button to exit the menu.

button to select OSD Language.

button, then the / button to select Subtitle.

button, then the / button to select Audio.

button, then the / button to select D VD Menu.

/ button to select Video.

button, then the / button to select Aspect Ratio.

/ button to select Video.

button, then the / button to select View Mode .

present on top/bottom or left/right of screen.
TV screen. Sides of the picture are cut off.

/ button to select Misc.
button, then press the / button to select “Use

/ button to select Misc.

button, then press the / button to select Screen

/ button to shift and

/ button to shift and

/ button until your

/ button until your

/ button to shift and

/ button to shift and

811-637091W010

Printed in China