Venturer PVS6281 Owner's Manual

Turning on the Unit

1. Slide the ON / STANDBY switch on the top of the unit to the ON position.

2. The DVD logo (start-up picture) will appear on the screen.

3. After use, slide the ON / STANDBY switch to the STANDBY (power off) position.

CONNECTIONS

The unit can playback

Region Management Information

Region Management Information: This unit is designed and manufactured to respond to the Region Management Information that is encoded on DVDs. If the region number printed on the DVD does not correspond to the region number of this unit, it cannot play that disc.

The region number of this unit is 1.

DISC FORMATS

Notes on Unauthorized Discs

You may not be able to play some DVDs on this unit, particularly if they were purchased from outside your geographic area or made for business purposes.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. When the provided plug does not fit into your AC power outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the AC power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been

damaged in any way, such as the AC power cord or plug is damaged, liquid has spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

DVDs [8cm/12cm disc]

Compatible

Audio CDs [8cm/12cm disc]

CONTROL REFERENCE GUIDE

1) VOLUME Control

Adjusts the volume.

2) AV IN / DVD Switch

3) Headphone Jack

4) AUDIO & VIDEO IN / OUT Jacks

5) CAR PLUG -12V / DC IN 9V Jack

6) LCD Screen

7) Open Knob

Press and hold to open the disc door.

8) ON / STANDBY Switch

9) POWER ON Indicator

When the ON / STANDBY switch is slide to ON position, the light will be on.

10) PREV Button

Press to go back to the previous chapters / tracks. Press and hold to perform fast reverse playback.

Disc Function or Operation that is Not Available

When the symbol appears on the screen, it indicates that the function or operation attempted is not available at that time. This occurs because the DVD manufacturer determines the specific functions of DVDs. Certain functions may not be available on some DVDs. Be sure to read the documentation provided with the DVD.

Using the Remote Control

• Point the remote control at the REMOTE SENSOR located on the unit.

• When using this unit in very bright light, the infrared REMOTE SENSOR may not work properly.

• The recommended effective distance for remote operation is about 16 feet (5 meters).

BATTERY REPLACEMENT

When the battery becomes weak, the operating distance of the remote control will be greatly reduced and you will need to replace the battery.

2. Insert one CR2025 (3V) size battery.

TO CHANGE REMOTE BATTERY

1. Open the battery door.

REMOTE CONTROL

Remove the PLASTIC sheet before USING the Remote Control.

Remote Control

1) VIDEO MODE button

Adjust Brightness, Panel Display and Contrast of the LCD screen.

2) PREV button

Move back through titles, chapters or tracks on a disc.

3) / SEARCH buttons SEARCH: Fast reverse playback. SEARCH: Fast forward playback.

4) GOTO button

Skip directly to a location on a DVD.

5) Cursor ( , , , ) buttons

Use to move between selections on a menu screen and adjust certain settings.

ENTER button

Confirm selections on a menu screen.

6) MEMORY button

Set titles/chapters in a favourite order.

SUBTITLE/ RETURN

98 07

ENTER

MEMORY

DISPLAY

AUDIO

GOTO

VIDEO MODE

STOP

PAUSE

PLAY

ANGLE

SETUP

A-B DISC

REPEAT

1 2

3 4

Unit

B. Using the Car Power Adapter

The 12V car power adapter allows the unit to be used with vehicles that have a 12V, negative ground electrical system.

WARNING: Disconnect the car power adapter when not in use. Not for use in 24V vehicles.

Fuse Replacement Instructions

Press and hold

FUSE

CAUTION:

Forcontinued protectionagainst risk of fire, replace only with same type and rating of fuse.

7) Number (0 - 9) buttons

Use when creating programs or locating a title/ chapter/track or specific time.

8) REPEAT A-B button

Perform point-to-point repeat playback on a DVD or CD.

REPEAT DISC button

Repeat a DVD chapter or title. Repeat a CD track or the whole disc.

SETUP button

When a DVD is stopped, display the unit’s SETUP menu.

9) SUBTITLE button

Select one of the subtitle languages programmed on a DVD (if available).

RETURN button

Return to normal operation after using the SETUP menu of a DVD.

10) AUDIO button

Select one of the audio sound tracks on a DVD (if more than one is available) or select the audio output mode on a CD.

11) ANGLE button

Switch between multiple camera angles when the DVD you are playing has been programmed with multiple camera angles.

12) DISPLAY button

Show status information on the screen.

13) STOP button

Stop playing a disc.

PLAY button

Start or resume playback of a disc.

PAUSE button

Press once to pause playback. Press subsequently to advance frame by frame on a DVD.

14) NEXT button

Move forward through titles, chapters or tracks on a disc.

15) MENU button

Enter and exit the main DVD menu.

WARNING: Do not dispose of the battery in a fire or it may leak and/or explode. WARNING: Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

Note: If the remote control is not going to be used for a long time, remove the battery.

NEXT Button

Press to advance chapters / tracks. Press and hold to perform fast forward playback.

STOP Button

Stops playing a disc.

PAUSE Button

Pauses playback of a disc. Each time you press the PAUSE button the picture advances one frame. Press the PLAY button to resume playback.

PLAY Button

Starts or resumes playback of a disc.

11) Mounting Strap

12) Remote Sensor

Receive the remote control unit signals.

13) Stand

14) Elastic Safety Band

Title, Chapter and Tracks

• DVDs are divided into “titles” and “chapters”. If the disc has more than one movie on it, each movie would be a separate “title”. “Chapters” are sections of titles.

• Audio CDs are divided into “tracks”. A “track” is usually one song on an Audio CD.

Note: Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded on them,

but some do not.

Chapter1

Title1 Title2

Chapter2 Chapter3 Chapter1 Chapter2

Track1 Track2 Track3 Track4 Track5

Manufactured under license from Dolby Laboratories. 'Dolby' and the double-D symbol are trademarks of Dolby Laboratories.

Dolby Digital

Dolby Digital is a technology developed by Dolby Laboratories. Soundtracks encoded in Dolby Digital can reproduce from one to 5.1 discrete channels of excellent quality audio. The unit automatically recognizes the Dolby Digital bitstream and provides a downmix suitable for two-channel listening. An additional Dolby Digital decoder is required for reproduction of the discrete multi-channel soundtracks available on many DVDs.

SOUND SYSTEM

Cautions:

• Use the provided 12V car power adapter/splitter only. Use with other car power adapters/splitters could damage the unit.

• The 12V car power adapter/splitter included with this unit are for its use only. Do not use them with other equipment.

• In the interest of traffic safety, do not operate this unit or view videos while driving a vehicle.

• Make sure the unit is securely fastened to prevent it from falling or flying through the air in the event of an accident.

• When the inside of the cigarette lighter socket is dirty with ashes or dust, the plug section may become hot due to poor contact. Be sure to clean the cigarette lighter socket before use.

• After use, disconnect the 12V car power adapter/splitter from both the unit and cigarette lighter socket.

1 2 3

10 11

13 14

C. Using the Car Power Splitter

The 12V car power splitter allows the unit to be used with vehicles that have a 12V, negative ground electrical system.

IMPORTANT NOTE: The included remote controls have different color keys to identify which unit they operate. The remote control with GREEN keys operates the unit which has GREEN buttons on the front of the unit. The remote control with BLUE keys operates the unit which has BLUE buttons on the front of the unit.

ACCESSORIES

Please check and identify the supplied accessories.

• To order accessories visit website http://www.venturer.com

Remote Control (with battery)......................................................................................................................... x 2

AC Power Adapter........................................................................................................................................... x 2

Car Power Adapter.......................................................................................................................................... x 1

Car Power Splitter ...........................................................................................................................................x 1

Mounting Strap ................................................................................................................................................x 2

Audio/Video Cable ..........................................................................................................................................x 1

Carrying Bag ....................................................................................................................................................x 1

POWER SUPPLY

A. Using the AC Power Adapter

The supplied AC power adapter operates on AC 120V.

Cautions:

• The AC power adapter included with this unit is for its use only. Do not use it with other equipment.

• When the unit is not going to be used for long time, disconnect the AC power adapter from the AC power outlet.

• When the AC power adapter is plugged in, the apparatus is not completely disconnected from the main power supply, even when the power is turned off.

Warning:

The AC power adapter is used as disconnect device and it should remain readily operable during intended used. In order to disconnect the apparatus from the mains completely, the AC power adapter should be disconnected from the mains socket outlet completely.

INSTALLATION GUIDE

Mounting

Straps

Safety

Band

Car Power

Splitter

Safety

Band

Remote Control

withBLUE rubber keys

Remote Control

withGREEN rubber keys

Unit

with BLUE buttons

Unit

with GREEN buttons

USING THE STAND FOR DESKTOP USE

This unit is designed to allow users to have a comfortable viewing angle.

• The angle can be adjusted approximately +8° / -5°.

• Gently push the top or bottom of the screen frame to adjust the viewing angle.

Caution:

• Do not force the screen frame over its maximum viewing angle settings as stated above. Attempting this will result in damage to the unit.

• Do not push the LCD screen. Gently push the screen frame to adjust.

SCREEN VIEWING ANGLE ADJUSTMENT

+8°

-5°

INSERTING A DVD OR CD

1. Open the disc door

Push and hold the OPEN knob to open the disc door.

2. Hold the disc by its sides and carefully place it onto the spindle with the label side facing up; push gently until you hear a "click".

3. Close the disc door. It takes a short while for your unit to load the disc. After loading, the unit will automatically bring you to the main menu of the disc or start playing the disc.

4. If the unit does not automatically start playing the disc, press the PLAY button.

Note:

When gently pulling the LCD screen cover outward, be careful not touch the screen.

+90

INSTALLING IN A VEHICLE

Use the supplied mounting straps when installing the unit on the back of the vehicle's headrest.

2. Tightly wrap the mounting strap around the headrest.

SAFETY WARNING!

• This unit should never be used by the vehicle's driver or left unsecured in the vehicle while driving.

• If this unit is being used in your vehicle, be sure that it is secured or held safely, and does not obstruct any safety device, including air bags or seat belts.

• All passengers should wear seat belts when using this unit in a moving vehicle.

• If in doubt, please contact your vehicle manufacturer for further advice.

1. Loop the safety band around

the headrest.

Mounting Strap

Elastic Safety Band

E - 6E - 3 E - 4E - 2 E - 5

LEFT SIDE OF UNIT

To DC IN 9V jack

To AC outlet

AC Power Adapter

To the cigarette lighter socket

Car Power Adapter

To CAR PLUG-12V jack

LEFT SIDE OF UNIT

To CAR PLUG12V jack

LEFT SIDE OF UNIT

To the cigarette lighter socket

Car Power Splitter

To CAR PLUG12V jack

Watching a DVD on your TV

1. Turn on the unit. Slide the AV IN / DVD switch to DVD.

2. Turn on the TV and follow the instructions included with it to play the DVD.

Notes:

• Make sure to use the correct Audio/Video cable. Connecting the plugs incorrectly may cause a weak signal.

• If your TV does not have Audio/Video inputs, you will need to purchase an RF modulator (sold separately) and follow the instructions included with it to connect the unit to your TV.

A. Connecting a TV

If your TV has Audio/Video inputs, you can connect the unit to your TV using the Audio/Video cable.

VIDEO

AUDIO

White YellowRed

Audio/Video Cable

(included)

LEFT SIDE OF UNIT

Listening on external audio equipment

1. Turn on the unit. Slide the AV IN / DVD switch to DVD.

2. Turn on your audio equipment and follow the instructions provided with it to select the AUDIO IN function.

Notes:

• Make sure to use the correct Audio/Video cable. Connecting the plugs incorrectly may cause a weak signal.

• If you have a stereo VCR, make sure you set it to stereo mode.

• Due to copyright protection, DVD movies cannot be copied. If you copy a DVD movie onto a videotape, the resulting copy will be unclear, with poor sound quality. This is NOT caused by a defective DVD system.

B. Connecting to a Stereo Receiver or Amplifier

The unit can play two channels Dolby Digital.

White YellowRed

AUDIO

STEREORECEIVER ORAMPLIFIER

No need to connect

the yellow video plug.

LEFT SIDE OF UNIT

Audio/Video Cable

(included)

Watching video equipment

1. Turn on the unit. Slide the AV IN / DVD switch to AV IN.

2. Turn on the video equipment and follow the instructions provided with it to playback.

Notes:

• Make sure to use the correct Audio/Video cable. Connecting the plugs incorrectly may cause a weak signal.

• If you have a mono VCR, the volume level from the speakers will be low.

C. Connecting to a Game System / Video Equipment

You can connect game system or other video equipment for playback through the unit.

GAMESYSTEM / VIDEOEQUIPMENT

VIDEO OUT

AUDIO OUT

White YellowRed

LEFT SIDE OF UNIT

Audio/Video Cable

(included)

D. Using Headphones / Earphones

• Turn down the volume before connecting, and then adjust the level.

• When headphones/earphones are connected, no sound will be emitted from the unit's speaker.

Caution: Avoid listening to sound at levels which may be harmful to your ears.

LEFT SIDE OF UNIT

Headphones

(3.5mmdiameter plug)

Icons Used on DVDs

Sample lcons

Note:

When playing back a CD-G (Graphics) or CD EXTRA disc, the audio portion will be played, but the graphic images will not be shown.

Language selections for audio

Language selections for subtitles

Screen aspect ratio

Multiple camera angles

Region code indicator

Push and hold the OPEN knob

E - 1E - 8 E - 9

CUSTOMIZING THE FUNCTION SETTINGS

Specifications and external appearance are subject to change without notice.

SAFETY PRECAUTIONS

The lightning flash with an arrowhead symbol, within the equilateral triangle, is intended to alert the user to the presence

of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to cause an electric shock.

The exclamation point within the

equilateral triangle is intended to alert

the user to the presence of important

operating and maintenance (servicing)

instructions in this owner’s manual.

* SEE BOTTOM OF UNIT FOR GRAPHIC SYMBOLS *

This product contains a low power laser device.

On Placement

• Do not use the unit in places that are extremely hot, cold, dusty, or humid.

• Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a cloth, or by

placing it on carpeting.

On Safety

• When connecting or disconnecting the AC power adapter, grip the plug and not the cord itself. Pulling the cord

may damage it and create a hazard.

• When you are not going to use the unit for a long period of time, disconnect the AC power adapter.

On Condensation

• When left in a heated room where it is warm and damp, water droplets or condensation may form inside the unit.

When there is condensation inside the unit, the unit may not function normally. Let the unit stand for 1 to 2 hours before turning the power on, or gradually heat the room and allow the unit to dry before use.

Rating Plate Location

• The rating plate is located on the bottom of the unit.

FCC Statements

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an AC power outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS ON OR NEAR THIS UNIT.

CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.

THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.

WARNING: Should any trouble occur, disconnect the AC power adapter and refer servicing to a qualified

technician.

Notes on Copyright

It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, or rent copyrighted material without permission. Apparatus Claims of U.S. Patent Nos. 6,836,549; 6,381,747; 7,050,698; 6,516,132 and 5,583,936 licensed for limited viewing uses only. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

CAUTION

INVISIBLE LASER RADIATION WHEN OPEN.

AVOID EXPOSURE TO BEAM.

Printed in China

811-628191W011

Cleaning the Disc

A defective or soiled disc inserted into the unit can cause sound to drop out during playback. Handle the disc by holding its inner and outer edges.

• Do NOT touch the surface of the unlabeled side of the disc.

• Do NOT stick paper or tape on the surface.

• Do NOT expose the disc to direct sunlight or excessive heat.

• Clean the disc before playback. Wipe the disc from the center outward with a cleaning cloth.

• NEVER use solvents such as benzine or alcohol to clean the disc.

• Do NOT use irregular shaped discs (example: heart shaped, octagonal, etc.). They may cause malfunctions.

Cleaning the Unit

• Be sure to turn the unit off and disconnect the AC power adapter before maintaining the unit.

• Wipe the unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth that has been dipped in a weak soap-and-water solution and wrung out thoroughly, then wipe with a dry cloth.

• Never use alcohol, benzine, thinner, cleaning fluid or other chemicals. Do NOT use compressed air to remove dust.

Important Note

• Before transporting the unit, remove the disc from the disc compartment.

MAINTENANCE

TROUBLESHOOTING GUIDE

SYMPTOM CAUSE (AND REMEDY)

• Ensure the AC power adapter is connected.

• The unit is not turned on.

• Make sure the infrared remote sensor is not blocked.

• Make sure the plastic sheet has been removed from the remote control.

• Point the remote directly at the infrared remote sensor on the unit.

• Replace the battery in the remote control with a new one.

• Use remote control with GREEN keys with the unit which has GREEN buttons. Use remote control with BLUE keys with the unit which has BLUE buttons.

• Make sure that ON mode is selected.

• The system is in pause mode. Press the PLAY button to return to normal play mode.

• The unit is in fast-forward or fast-reverse mode. Press the PLAY button to return to normal play mode.

• Make sure the AUDIO/VIDEO output connections are correct.

• The DTS DVD cannot be decoded to have speaker output.

• The unit is too hot; shut off the unit for 30 minutes to cool it down.

• The region number of the disc doesn't match the region number of this unit.

• Clean the disc.

• The disc is scratched.

• Adjust the LCD's brightness and contrast using the VIDEO MODE button on the remote control.

• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol.

• Clean the disc.

• There is no disc inside (“No Disc” appears on the screen).

• Insert the disc correctly with the playback side facing down.

• Clean the disc.

• A non-NTSC disc has been inserted. The unit and disc region number are incompatible.

• Condensation may have formed inside the unit due to a sudden change in temperature. Wait about an hour for it to clear and try again.

No power.

The remote control does not function.

No sound or only a very low-level sound is heard.

No picture.

The picture is not clear.

Severe hum or noise is heard.

The disc does not play.

DVD PROGRAMMABLE MEMORY

DVD

VIEWING JPG FILES

Need More Help?

DO NOT RETURN THIS PRODUCT TO THE STORE

Please visit online help at

http://www.venturer.com

DUAL SCREEN PORTABLE DVD PLAYER

OWNER’S MANUAL

You can play a specific title or chapter repeatedly. (Title repeat, chapter repeat, A-B repeat)

Repeating a Chapter

1. While the DVD is playing, press the REPEAT DISC button until the “

Chapter

” indicator displays on the screen.

The current chapter is played repeatedly.

Repeating a Title

2. While the DVD is playing, press the REPEAT DISC button until the “

Title

” indicator displays on the screen.

The current title is played repeatedly.

To Resume Normal Playback

3. While the DVD is playing, press the REPEAT DISC button until the “

RepeatOff

” indicator displays on the screen.

You can play a single track or the whole disc repeatedly.

Repeating a Single Track

1. While the CD is playing, press the REPEAT DISC button until the “

RepeatOne

” indicator displays on the screen.

The current track is played repeatedly.

Repeating the Whole Disc

2. While the CD is playing, press the REPEAT DISC button until the “

RepeatAll

” indicator displays on the screen.

The whole disc is played repeatedly.

To Resume Normal Playback

3. While the CD is playing, press the REPEAT DISC button until the “

Off

” indicator displays on the screen.

Repeating a Specific Section

You can play a specific section repeatedly.

1. While the disc is playing, press the REPEAT A-B button at the beginning of the section (“

” is displayed)

you want to play repeatedly.

2. Press the REPEAT A-B button again at the end of the section (“

” is displayed).

3. The Unit will immediately begin replaying your selection.

To Resume Normal Playback

4. While the disc is playing, press the REPEAT A-B button until the “

ABOFF

” indicator displays on the screen.

Notes:

• Some discs may not permit A-B repeat operation.

• You cannot set the A-B repeat function for a segment that includes multiple camera angles.

• You can specify a segment only within the current title or track.

• There may be a slight difference between point A and the location where playback actually resumes depending on the disc.

DVD

Locating a Specific Chapter

If you know the chapter number for the chapter that you want to play, you can locate it by directly selecting that number.

1. Press the GOTO button.

2. Press the corresponding number buttons (2 digits) for the chapter you want. (For example: 02, 08, 10 or 15.) (If you press only 1 numeric button, press the ENTER button to confirm.)

3. Playback starts from the selected chapter.

Notes:

• If the chapter number entered is not permitted by the DVD, "

Inputinvalid

" will display. You should press the

GOTO button again and re-enter correct number.

• Some discs may not respond to this process.

• This method of locating a chapter is available only on a DVD that contains chapter numbers.

Locating a Specific Title

If a DVD contains title numbers, you can locate a specific title by directly selecting its title number.

1. Press the GOTO button.

2. Press the / button to highlight title number, press the corresponding number buttons (2 digits) for the title you want. (For example: 02, 08, 10 or 15.) (If you press only 1 numeric button, press the ENTER button to confirm.)

3. Playback starts from the selected title.

Notes:

• If the title number entered is not permitted by the DVD, "

Inputinvalid

" will display. You should repeat steps

1 and 2 to re-enter correct numbers.

• Some discs may not respond to this process.

• This method of locating a title is available only on a DVD that contains title numbers.

Locating a Specific Time

You can move to a specific location by entering its corresponding time (hours, minutes, seconds).

1. Press the GOTO button two times.

2. Press the corresponding number buttons (5 digits: X:XX:XX, for example: 0 30 05, 1 08 23, 1 22 56.) for the

setting point you want.

3. Playback starts from the selected section.

Notes:

• If the time entered is not permitted by the DVD, "

Inputinvalid

" will display. You should re-enter correct time.

• Some discs may not respond to this process.

• Some scenes may not be located as precisely as you specified.

• This method for accessing specific locations is available only within the current title of the DVD.

LOCATING A DESIRED SECTION

DVD

REPEAT PLAYBACK

DVD

3. Press the PLAY button to start memory playback. (“

Program

” appears on the screen.)

4. To resume normal playback from memory playback

1).Press the MEMORY button to display the memory menu.

2).Use the Cursor buttons ( , , , ) to move the highlighted bar to “Stop”. Press the ENTER button to confirm “Stop”.

3).Press the ENTER button to confirm “Exit”. It will return to normal playback. (“

Program

” disappear from the

screen.)

Notes:

• If the title or chapter number entered is not permitted by the DVD, it will disappear. You should re-enter correct number.

• You should input items one by one following the 1, 2, 3 ... sequence.

• If the DVD contains only one title, you can only arrange order for chapters.

• Some discs may not permit memory playback operation.

• If you select repeat during memory playback, the DVD player repeats the current memory playback.

• If you press the MEMORY button while the display appears on the TV screen, the display disappears.

• The programmed selections will be cleared when you press the STOP button two times, open the disc tray or turn off the DVD player.

This unit can play JPG files recorded on a CD-R or CD-ROM disc (CD-RW is not recommended).

Viewing JPG Files

1. Press and hold the open knob to open the disc door.

2. Hold a JPG file disc by its edges and gently push it onto

the spindle with the label side facing up until you hear a “click”.

3. Close the disc door. The JPG files on the disc will be displayed one by one automatically.

4. Press the MENU or

STOP button to display a folder list.

Press the / button to highlight a JPG file to play. Press the PLAY button to start playback.

Notes:

• You can press the PAUSE button to freeze the picture. Press the PLAY button to resume picture slide show.

• You can press the STOP button to quit playback.

• You can press the PREV or NEXT button to change the picture.

• You can press the ANGLE button to rotate direction of the picture by 90o.

• Some discs may not permit this operation.

00:00 00:00 001/035

DSCN0281 DSCN0282 DSCN0283 DSCN0284 DSCN0285 DSCN0286

Language Setup

1. Press the SETUP button in stop mode.

2. Press the button to select Language Setup Page.

3. Press the / button to select the option (OSD Language,

Audio, Subtitle or Disc Menu), then press the button.

4. Press the / button to select your preferred language, then press the ENTER button to confirm.

5. Repeat steps 3 and 4 to adjust other options. Press the button to return to the previous menu.

6. Press the SETUP or RETURN button to exit the menu.

Notes:

• Some DVDs may not play in the audio language selected. A prior language may be programmed on the disc.

• Some DVDs may be set to display subtitles in a language other than the one you selected. A prior subtitle language may be programmed on the disc.

• Some DVDs allow you to change subtitle selections only via the disc menu. If this is the case, press the MENU button and choose the appropriate subtitle language from the selection on the disc menu.

• Some DVDs may not include your pre-selected language. In this case, the DVD player automatically displays disc menus consistent with the disc's initial language setting.

Go To LanguageSetup Page

- - Language Setup Page - -

System

Language

Video

OSD Language Audio Subtitle Disc Menu

Eng Eng Off Eng

Video Setup

1. Press the SETUP button in stop mode.

2. Press the / button to select Video Setup Page.

3. Press the / button to select the option (Brightness or

Contrast), then press the button.

4. Press the / button to adjust the setting, then press the ENTER button to confirm.

5. Repeat steps 3 and 4 to adjust other options. Press the

button to return to the previous menu.

6. Press the SETUP or RETURN button to exit the menu.

Brightness Contrast

Go To Video Setup Page

- - Video Setup Page - -

Language

00 00

System

Video

Playing Titles/Chapters in a Favourite Order

You can combine your favourite titles/chapters and play them in the order you determine.

1. Press the MEMORY button while a DVD is playing. The following display appears.

Tv Display Default

Wide No

Go To System Page

- - System Page - -

System

Language

Video

System Setup

1. Press the SETUP button in stop mode.

2. Press the / button to select System Page.

3. Press the / button to select the option (TV Display or

Default), then press the button.

4. Press the / button to adjust the settings, then press the ENTER button to confirm.

5. Repeat steps 3 and 4 to adjust other options. Press the

button to return to the previous menu.

6. Press the SETUP or RETURN button to exit the menu.

Default

It takes 3-5 seconds to reset the DVD settings to the factory default.

TV Display

Pan Scan

• When wide-screen video is played, this mode clips the right and left sides of the image so that it can be viewed on a conventional screen.

• Some wide-screen DVDs that do not permit Pan Scan mode playback are automatically played in letterbox mode (black bands that appear at the top and bottom of the screen).

Letter Box

• When wide-screen video is played in this mode on a conventional screen, black bands appear at the top and bottom of the screen.

Wide Screen

• This is the correct mode for playing wide-screen videos on the unit screen or other external wide-screens.

Notes:

• The displayable picture size is preset on the DVD. Therefore the playback picture of some DVDs may not conform to the picture size selected.

• When you play DVDs recorded in the 4:3 aspect ratio, the playback picture will always appear in the 4:3 aspect ratio regardless of the TV display setting.

• Select Wide Screen to conform the LCD screen on the unit. Always be sure that your TV display conforms to the actual TV in use if you connect the unit to a TV.

Wide Screen

Letter Box

Cut off when a wide-screen video image is played.

Pan Scan

2. Input the title (2 digits) and chapter (2 digits) by pressing the number buttons. (For example: 01 02, 02 05, 02

11.) It will move to the next item automatically.

• You can use the Cursor buttons ( , , , ) to move the highlighted bar to any item, and re-enter the title and chapter. (Press the NEXT / PREV to move to the the next / previous setup page.)

• You can use the Cursor buttons ( , , , ) to move the highlighted bar to “Clear”, “Exit”, “Start” or “Next / Prev”, and press the ENTER button to confirm.

Clear: Delete all the input programs. Exit: Exit memory menu and return to normal

playback.

Start: Start memory playback. Next / Prev:Move to the the next / previous setup

page.

This owner’s manual explains the basic instructions for operating this unit. Some DVDs are produced in a manner that allows specific or limited operation during playback. Therefore, this unit may not respond to all operating commands. THIS IS NOT A DEFECT. Please refer to the instructions accompanying the specific DVD in question for more information about the options available on that DVD.

“ ” may appear on the screen during operation. A “ ” means that the desired operation is not permitted by the unit or disc.

PLAYING A DISC

Basic playback

DVD

Playing a Disc

1. Slide the ON / STANDBY switch on the top of the unit to the ON position. See CUSTOMIZING THE FUNCTION SETTINGS before proceeding to step 2.

2. Press and hold the open knob to open the disc door.

3. Hold the disc by its sides and carefully place it onto the spindle with the label side facing up, pushing gently

until you hear a “click”.

4. Close the disc door. It takes a short while for your unit to load the disc. After loading, the unit will automatically bring you to the main menu of the DVD or start playing the DVD.

5. If the unit does not automatically start playing the DVD, press the PLAY button.

Pausing Playback (Still Mode)

Press the PAUSE button. To resume normal playback, press the PLAY button. Each time you press the PAUSE button, the picture advances one frame.

Stopping Playback

Press the STOP button at the location where you want to interrupt playback. To resume playback at the position where the disc was stopped, press the PLAY button. If you press the STOP button twice, the unit’s memory will be cleared and pressing the PLAY button will reset the DVD to the beginning.

Fast Forward / Fast Reverse

1. Press the SEARCH or SEARCH button when a disc is playing. Each time you press the SEARCH or SEARCH button, the playback speed changes in the following sequence:

2. Press the PLAY button when you reach the desired point to resume normal playback.

Notes:

• The DVD player mutes sound and subtitles during reverse and forward scan of DVDs.

• The fast playback speed may differ depending on the disc.

Skip (Forward / Reverse)

• Press the NEXT button to advance chapters/tracks.

• Press the PREV button to go back to current or previous chapters/tracks.

• For an Audio CD, use the number buttons on the remote control to the desired track number.

Audio Selection

On some DVDs, the sound is recorded in two or more formats. Follow the directions below to select the preferred language and sound system.

1. While a disc is playing, press the AUDIO button to show the current audio format number.

2. Press the AUDIO button repeatedly to select the desired audio format.

Notes:

• If only one audio format is recorded on the DVD, the number does not change.

• Some DVDs allow you to change audio selections only via the disc menu. If this is the case, press the MENU button and choose the appropriate language on the disc menu.

• You can select different audio channels (Stereo, Mono Left, Mono Right or Mix-Mono) on an Audio CD by pressing the AUDIO button repeatedly.

Subtitle Selection

1. While a DVD is playing, press the SUBTITLE button to display the current language setting, as shown in the

example.

2. Press the SUBTITLE button repeatedly to select the desired subtitle language. You can turn subtitles off by pressing the SUBTITLE button repeatedly until the “

Subtitle Off

” is displayed.

Notes:

• Some DVDs are set to display subtitles automatically, and you cannot turn them off even if you set the subtitle function to off.

• During some scenes, the subtitles may not appear immediately after you select your desired scene.

• The number of subtitle languages recorded differs depending on the disc. If only one language is recorded, the language does not change.

• This function can only be used for discs on which subtitles have been recorded in multiple languages.

• Some DVDs allow you to change subtitles only via the disc menu. If this is the case, press the MENU button and choose the appropriate subtitle on the disc menu.

Angle Selection

Some DVDs contain scenes that have been shot from a number of different angles. For these discs, the same scene can be viewed from each of these different angles.

Note: This function can only be used for discs on which scenes shot from multiple angles have been recorded.

Display Function

While the disc is playing, press the DISPLAY button repeatedly to display information on operation status.

Adjust the LCD Screen

You can adjust Brightness, Panel Display and Contrast of the LCD screen.

1. Press the VIDEO MODE button.

2. Press the / button to select Brightness, Panel Display or Contrast.

3. Press the / button to change the setting.

4. Press the VIDEO MODE button to exit the menu.

Sequence of angle shots

(Example)

1. While you are playing a DVD with different angles recorded, press the ANGLE button to view the number of current angles available.

2. Press the ANGLE button repeatedly to change the scene to the next recorded angle.

• After approx. two seconds, playback will continue from the new

angle selected.

• If no button is pressed within 10 seconds, playback continues

without changing the current angle.

E - 7

1/3

1/311

/31 /32 /33

Chapter Elapsed Tt 01/03 Ch 03/12 0:13:26

Chapter Remain Tt 01/03 Ch 03/12 0:05:42

Title Remain Tt 01/03 Ch 03/12 0:36:08

Display Off

Subtitle 02/03:Spanish

Audio 1/3:Dolby D 2ch English

Subtitle 02/03:Spanish

Audio 1/3:Dolby D 2ch English

Subtitle 02/03:Spanish

Audio 1/3:Dolby D 2ch English

Display Off

Chapter Elapsed Tt 01/03 Ch 03/12 0:13:26

Subtitle 02/03:Spanish

Audio 1/3:Dolby D 2ch English

Chapter Remain Tt 01/03 Ch 03/12 0:05:42

Subtitle 02/03:Spanish

Audio 1/3:Dolby D 2ch English

Title Remain Tt 01/03 Ch 03/12 0:36:08

Subtitle 02/03:Spanish

Audio 1/3:Dolby D 2ch English

Subtitle 02/03:Spanish

2x 4x 8x

16x

2x 4x 8x

16x

2x 4x 8x

16x

2x 4x 8x

16x

Title 01/03 Chapter 03/12

Title 01/03 Chapter 00/00

Title 01/03 Time

Clear Exit Next

Tt:01ch:05

Tt: ch:

Start

Tt: ch:

Clear Exit Next

Tt:01ch:05

Tt: ch:

Start

Tt: ch:

Venturer PVS6281 Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual