Veho SmartFix User Manual

-0-

-1-

Table of Contents

1. Precaution .................................................................2

2. Preparation................................................................5

z S tandard Accessories.....................................5

z Part Names.....................................................6

z Installing the Battery Pack..............................8

z Charging the Battery Pack………………........9

3. Place Film/ Slide Into The Holder............................11

4. Using the Digitize Image Copier..............................12

5. Playback Mode........................................................18

6. Delete Mode............................................................19

7. To Link the Card to Computer..................................21

8. Edit the Pictures.......................................................24

9. Appendix………………………..……………...………31

z Specifications................................................31

z Icon & Indicators...........................................32

z System Requirements...................................33

EN

-2-

Welcome

Thank you for purchasing a Digitize Image Copier.
Please take a moment to read through this manual. Its
contents will send you on an educational journey into your
recorder multiple capabilities.

1. Precaution

Before using Digitize Image Copier, please ensure that
you read and understand the safety precautions
described below. Always ensure that the Digitize Image
Copier is operated correctly.

• Never operate Digitize Image Copier inside of an
aircraft or anywhere else where operation of such
devices is restricted. Improper use creates the risk
of serious accident.

• Do not try to open the case of Digitize Image Copier
or attempt to modify Digitize Image Copier in any
way. High-voltage internal components create the
risk of electric shock when exposed. Maintenance
and repairs should be performed only by authorized
service providers.

• Keep Digitize Image Copier away from water and
other liquids. Do not use Digitize Image Copier with
wet hands. Never use Digitize Image Copier in the
rain or snow. Moisture creates the danger of fire and
electric shock.

• Keep Digitize Image Copier and its accessories out
of the reach of children and animals to prevent
accidents or damage to the Digitize Image Copier.

-3-

If you notice smoke or a strange odor coming from
Digitize Image Copier, turn the power off immediately.
Take Digitize Image Copier to the nearest authorized
service center for repair. Never attempt to repair
Digitize Image Copier on your own.

• Use only the recommended power accessories. Use
of power sources not expressly recommended for
Digitize Image Copier may lead to overheating,
distortion of the equipment, fire, electrical shock or
other hazards.

• Digitize Image Copier may become slightly warm
during use. This does not indicate malfunction.

• If the exterior of Digitize Image Copier needs
cleaning, wipe it with a soft, dry cloth.

EN

-4-

FCC Notice

This equipment has been tested and found to comply with
the limits for a Class B Digitize device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy. If not installed
and used in accordance with the instruction, it may cause
harmful interference to radio communication. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment on the off,
the user is encouraged to try to correct the interference by
one or more the following suggestion.

z Reorient or relocate the receiving antenna.
z Increase the distance between the equipment and

the receiver.

z Connect the equipment to a different power outlet

other than the one where the receiver is connected.

z Consult an experienced television or radio

technician for help.

CAUTION

To comply with the limits for a Class B Digitize device,
pursuant to Part 15 of the FCC Rules, this device must
only be installed on computer equipment certified to
comply with the Class B limits.

-5-

2. Preparation

St andard Accessories

Digitize Image Copier QOG CD

Slide Holder Negative Holder

110 Film Holder Clean brush

USB cable Lithium Battery

EN

-6-

Part Names

-7-

Note: We suggest using bundled brush to insert into the Digitize
Image Copier slot and clean the glass surface periodically to
produce a clear image. Please make sure your film negatives/
mounted slides and cover trays are clean before inserting into
the Digitize Image Copier as well. Dust or dirt from the negatives
and cover trays will affect the quality of your scanned images.

EN

-8-

Installing the Battery Pac k

1. Open the battery compartment cover by lightly
pressing and sliding it back as shown.

2. Insert the supplied battery. Make sure the battery
label is facing upwards and the (+ and -) ends of the
battery match to the polarities indicated in the battery
compartment.

3. Snap the cover back into place.

Battery power status

-9-

Charging the Battery Pack

The battery pack is not charged at the time of purchase
and therefore needs to be charged before use. If the
battery charge becomes low while you are using the
copier, it is recommended to recharge it as soon as
possible.

1. Insert the battery pack into the battery compartment
(see page 8)

2. You may charge the battery in 2 ways:

(a) Plug the USB mini B of the supplied USB cable to

the USB port of the copier, and plug the other USB
end into the USB port of your computer/notebook.

Please charge the battery at least 5.5~6 hours

prior to your first use.

EN

-10-

(b) Plug the USB mini B of the supplied AC adaptor

(optional) to the USB port of the copier, and plug
the adaptor to the power outlet.

Please charge the battery at least 2.5~3 hours

3. Red LED will light on during charging. When the
battery pack is fully charged, the red LED light will be
off and you may disconnect the charging connections.

Status LED:
Red: The Image Copier is OFF, the battery is charging.
Purple: The Image Copier is ON, the battery is charged

simultaneously.

Blue: The Image Copier is ON, the battery is not charged

or no battery is loaded.