Page 1
INSTRUCTION MANUAL
Vanguard-HD Mega pixel
IR OUTDOOR CAMERA
Page 2
Page 3
CONTENTS
WARNING & CAUTION 2
GENERAL FEATURES 4
NAME OF EACH PART 5
INSTALLATION 7
CONNECTION 11
SPECIFICATIONS 12
OSD MENU SETTING 14
TROUBLESHOOTING 16
DIMENSIONS 17
1
Page 4
WARNING & CAUTION
If you fail to read this information and handle the product incorrectly, death or
serious injury may occur.
The unit should be installed by the trained Personnel.
Switch off immediately if the product emits smoke or abnormal heat.
Never install the product in area exposed to oil or gas.
Never touch the power cord with wet hands.
Clean only with dry cloth.
Ensure that the product is not subjected to strong impacts and vibration.
Never expose the camera to direct sunlight
WARNING
Never disassemble the unit by
unauthorized person.
Serious and Permanent
damage will occur.
2
Page 5
CAUTION
WARNING & CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
un-insulated "dangerous voltage" within the product's enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
LABEL
4. SCREW M4x20 4EA
5. CALBLOCK 6x30 4EA
6. SCREW 4x30 4EA
7. CAP SCREW 2EA
3
Page 6
GENERAL FEATURES
*
1/3" Panasonic 2.2M Progressive Scan CMOS
*
HD-SDI : 1080@30p/25p, 720@60p/50p
*
NTSC, PAL CVBS without WDR
*
TDN ICR Mega pixel lens
*
40PCS High performance IR LEDs
*
Joystick type OSD control key
*
Wide Dynamic Range compensation
*
Adaptive Contrast Enhancer
*
Supports various digital features of Mirror, Flip, Digital Zoom,
Privacy Masking, Motion Detection, Sharpness control and shading
*
IP-67 rated waterproof frame housing
*
3-Axis bracket (Wall, Ceiling, Pole mount available)
*
Easy installation by hinge type junction box (option)
*
Adjustable Zoom & Focus of the lens externally
*
Adjustable Day & Night lux level value
*
Fan & Heater (option)
4
Page 7
NAME OF EACH PART
1. Sunvisor
2. Camera Body
3. Function Cover
4. Function Part
5. IR LED Lamp
6. Lens
7. Camera Bracket
8. Lens Control Lever
9. Set Screw groove for Sunvisor
10. X-Axis Set Screw
11. Y-Axis Set Screw
12. Z-Axis Set Screw
FIG.1
5
Page 8
NAME OF EACH PART
FUNCTION PART
FIG.2
FUNCTION
Extra Video Out CVBS Output
1
IR Gain IR Gain Control
2
3
3 Lux / 6 Lux CDS Sensitivity Control
4
ON / OFF IR LED ON / OFF
OSD Button Up, Down, Set, Left, Right
5
6
Page 9
INSTALLATION
Template Label
FIG.3
6mm
81mm
86mm
Seal Tape
Calblock( 6x30)
Hole Diameter : 6mm
Depth : 30mm
FIG.4
FIG.5
1. When you need to install a camera on the surface of a concrete wall, you can drill
a hole like Fig.3 exactly by using a Template Card offered by accessory.
2. As Fig.4, please set a Calblock in the hole of the wall.
3. After connect a Power Jack and Video Connector. Please wrap and tighten by
using a seal tape (water-proof tape) to prevent a leak of water.
7
Page 10
INSTALLATION
Screw 4x30
FIG.6
Wrench 2mm
Wrench 3mm
FIG.7
FIG.8
4. Like Fig.6, after put the cable connector part into the bracket, please fix the
bracket on the wall by use of screws.
5. Like Fig.7, after set the camera to desired direction, please fix tightly by L-Wrench.
6. After finish adjustment of OSD function, please tighten the screw tightly to prevent
a leak of water close the cover then. (Fig.8)
8
Page 11
INSTALLATION
How to install Junction Box
Template Label
6mm
84mm
46mm
Calblock( 6x30)
Hole Diameter : 6mm
Depth : 30mm
FIG.9 FIG.10
Screw 4x30
FIG.11
1. Like Fig.9, please make a screw sign hole on the wall for fixation of Junction Box
by use of offered Template Label.
2. As Fig.10, please set a Calblock in the hole of the wall.
3. Then stick by screw by using a Junction Box on the surface of a wall.
9
Page 12
INSTALLATION
Screw M4x60
Nut M4
FIG.12 FIG.13
4. Joint the Camera bracket to the Junction Box, then put the Screw
into a Hinge part after that tighten by Nut. (Fig.12)
5. Connect a cable and like Fig.13, please join Bracket part.
(Please refer to Page 11 regarding cable connection)
How to install Ceiling & Pole
Pole Mount Bracket
(option)
Screw M4x20
FIG.14 FIG.15
1. In case of installation on Ceiling or Pole, please refer to Fig.14 & Fig.15.
10
Page 13
CONNECTION
DUAL POWER TYPE
FIG.16
1. Terminal Block (Accessory)
2. DC Jack Cable (Accessory)
3. Adaptor (DC12V or AC24V)
4. Video Output (HD-SDI)
5. Seal Tape
DC12V POWER TYPE
*A power source connection is nonpolar.
*A power source connection is nonpolar.
1. DC Jack
2. Adaptor (DC12V)
3. Video Output (HD-SDI)
4. Seal Tape
CAUTION : After connecting the cable, please make sure bind by using a
Seal Tape to prevent a leak of water.
FIG.17
11
Page 14
SPECIFICATIONS
MODEL Full HD Mega Pixel IR Outdoor Camera
NTSC (50Hz) / PAL (60Hz)
1/3'' Panasonic CMOS
Progressive Scan
2010(H) X 1108(V) : 2.2Mega pixel
1944(H) X 1092(V) : 2.1Mega pixel
2.8-12mm Mega Pixel Lens
ICR (Mechanism Filter Mountable)
0.1 lux @ F1.4, 30IRE
1080P / 720P
30/25@1080p, 60/50@720p
FULL / CUT
OFF/ON
Internal
60Hz :1/30~1/30,000sec, 50Hz : 1/25~1/30,000sec
1 HD-SDI
CVBS (NTSC, PAL) without WDR
Digital : 1080@30p/25p, 720@60p/50p
Analog : 700TVL
Bulit-in
English
0~20
0~20
AUTO / MANUAL
1/30(25),60(50),120(100), 250, 700, 1K, 1.6K, 5K, 7K, 10K, 30K
OFF/X2/X3/X4
AUTO / PUSH LOCK / MANUAL
COLOR TEMP. / RED GAIN / BLUE GAIN
OFF / WDR / BLC / ACE
0~20
0~20
OFF / LOW / MIDDLE / HIGH
CAMERA
SYSTEM
VIDEO
OSD
EXPOSURE
WHITE
BALANCE
WDR / BLC
/ ACE
DNR
TV System
Image Device
Scanning System
Total Pixels
Effective Pixels
Lens
Day & Night System
Min. Illumination
SDI FORMAT
SDI FPS
CVBS SCALE
CVBS OUT
Sync System
Electronic Shutter
Output 1
Output 2
Resolution & frame rate
On Screen Display
Language
BRIGHTNESS
AGC
SHUTTER MODE
SHUTTER SPEED
SENS-UP
MODE
MANUAL MODE
MODE
BLC POS X, Y
BLC SIZE X, Y
12
Page 15
SPECIFICATIONS
MODEL
DAY &
NIGHT
IMAGE
SPECIAL
POWER &
ENVIRONMENTAL
Full HD Mega Pixel IR Outdoor Camera
MODE
DWELL TIME
D->N LEVEL
N->D LEVEL
SHARPNESS
COLOR LEVEL
MIRROR
FLIP
LENS SHADING
D-ZOOM
COMM ADJUST
PRIVACY
HLM
SMART IR
MOTION
OPERATING TEMP./ HUM.
STORAGE TEMP./ HUM.
POWER
POWER CONSUMPTION
IR LED
DIMENSION
WEIGHT
AUTO / EXT / COLOR / B&W
1~10sec
0~20
0~20
0~20
0~20
OFF/ON
OFF/ON
OFF/ON
1~40X
CAM ID / BAUD RATE / 485 TERM.
OFF / ON (position, size, color adjustable)
OFF / ON (level, color adjustable)
ON / OFF
OFF / ON (sensitivity adjustable)
oo oo
-10 C~+50 C (Fan / Heater type (Option) -40 C~+70 C) /
30%~80% RH
oo
-20 C~+60 C / 20%~90% RH
DC type (Max. 6.5W) /
Dual Type (DC:Max. 7W, AC:Max. 9W)
DC type (Max. 450mA) /
Dual Type (DC:Max. 500mA, AC:Max. 350mA)
Round 40pcs (30deg)
98mm(W) X 88.5mm(H) X 149mm(L)
1.1 Kg
13
Page 16
OSD MENU SETTING
SETUP MENU
LENS
EXPOSURE
WHITE BALANCE
WDR/BLC/ACE
DNR
DAY&NIGHT
IMAGE
SPECIAL
SUB MANU 1 SUB MANU 2 VALUE
DC
MANUAL
BRIGHTNESS
AGC
SHUTTER MODE
SHUTTER SPEED
SENS-UP
MODE
COLOR TEMP.
RED GAIN
BLUE GAIN
PUSH AUTO
MODE
BLC POS-X
BLC POS-Y
BLC SIZ-X
BLC SIZ-Y
MODE
SENSOR
DWELL TIME
D->N LEVEL
N->D LEVEL
SHARPNESS
COLOR LEVEL
MIRROR
FLIP
LENS SHADING
GAMMA
D-ZOOM
COMM ADJUST
PRIVACY
HLM
MOTION
CAM ID
BAUDRATE
485 TERM.
OFF
MASK SEL.
MASK MODE
X-POSITION
Y-POSITION
X-SIZE
Y-SIZE
MASK COLOR
OFF
HLM LEVEL
HLM COLOR
OFF
SENSITIVITY
OUTDOOR / INDOOR
-
0~20
0~20
AUTO / MANUAL
1/30(25), 60(50), 120(100), 250, 700, 1K, 1.6K, 5K, 7K, 10K, 30K
OFF/X2/X3/X4
AWB / ATW / PUSH LOCK / MANUAL
LOW / MIDDLE / HIGH
0~20
0~20
Press LEFT or RIGHT key
OFF / WDR / BLC / ACE
0~20
0~20
0~20
0~20
OFF / LOW / MIDDLE / HIGH
AUTO / EXT / COLOR / B&W
AGC / CDS
1~10sec, 1sec / step
11(bright) ~ 20(dark)
0(bright) ~ 10(dark)
0~20
0~20
OFF/ON
OFF/ON
OFF/ON
0~4
1,2,4,6,8,12,14,16,18,20,22,24,26,28,30,32,34,36,38,40X
0~255
2400,4800,9600,19200,38400,57600,115200
OFF/ON
0~29
OFF/ON
0~60
0~40
0~40
0~40
BLK, WHT, YEL, CYN, GRN, MAG, RED, BLU
0~20
BLK, WHT, YEL, CYN, GRN, MAG, RED, BLU
0~20
*NOTE 1
*NOTE 2
*NOTE 3
*NOTE 1
*Factory setting
14
Page 17
OSD MENU SETTING
SETUP MENU
SYSTEM
FACTORY DEFAULT
RETURN
EXIT
*NOTE 1; WDR is not operated at 'SHUTTER MODE=MANUAL'.CVBS OUT is OFF at WDR mode.
*NOTE 2; OSD Button action is delayed while SENS-UP operation is performed.
*NOTE 3; AWB operation is performed while the button is pressed and shifts to hold mode when the button is
SUB MANU 1 SUB MANU 2 VALUE
SDI FORMAT
SDI FPS
FREQ (NT/PAL)
CVBS SCALE
CVBS OUT
1080P / 720P
30/25@1080p, 60/50@720p
60Hz(NTSC) / 50Hz(PAL)
FULL / CUT
OFF/ON
Reset to factory setting
Return to previous menu
Exit SETUP menu
*Factory setting
*NOTE 4
*NOTE 1
With WDR mode, the frame speed is decreased from 30fps to 15fps(or from 60fps to 30fps)
Press the button more than 1 sec.
released.
*NOTE 4; Factory default 60Hz
15
Page 18
TROUBLESHOOTING
PROBLEM SOLUTION
No picture Check if the power cable is connected properly.
Check if the video cable is connected correctly.
Camera with excessive
heat, Abnormal motion
or Black lines on the
screen.
Blinking Screen Check if the Camera faces the Sun or
Unclear Screen Check if the Lens is dirty. If necessary, clean the
No operation of Color
Auto mode
No operation of
Motion Detection
Inaccurate Color Insure that 'White Balance' is set properly.
Check if the power supply meets the minimum
requirements and that the power supply is
functioning properly.
fluorescent lamp.
Check if the Auto Iris Lens connector is
connected properly.
lens with a soft cloth or lens brush.
Check the camera positioning and setting.
Adjust the camera position if too much light is
entering the iris.
Check the Back-Focus Setting.
Check if you set 'Color' mode 'EXT/ON/OFF'
Check if you set 'Gain' mode off.
Check if 'Motion Detection' mode is on
Check if the 'MD Level' is set too low.
Check if the 'MD Area' is set properly.
16
Page 19
DIMENSIONS
UNITS:mm
17
Page 20
MP86C028
Loading...