VADDIO HD-Series, RoboSHOT Installation And User Manual

Installation and User Guide

BLURB

IN-CEILING™ HALF-RECESSED ENCLOSURES

For the Vaddio™ ClearVIEW™, PowerVIEW™ and RoboSHOT™ HD PTZ Cameras

Part Number: 999-2225-050 for HD-Series Cameras

Part Number: 999-2225-150 for RoboSHOT Cameras

©2014 Vaddio - All Rights Reserved ● IN-Ceiling Half-Recessed Enclosure for HD and RoboSHOT Cameras ● Document Number 342-0177 Rev. E

IN-Ceiling Half-Recessed Enclosure for HD Series and RoboSHOT Cameras

V

Overview:

Vaddio’s IN-Ceiling, Half-Recessed Enclosure is an attractive,
easy to install, partially recessed and inverted, PTZ camera
mounting system. IN-Ceiling Half-Recessed Enclosure is
compatible with the all WallVIEW systems (ClearVIEW and
PowerVIEW (HD-30/22/20

SE

/20/19/18) and the RoboSHOT

series camera systems.

The enclosure features a sealed, recessed, metal ceiling camera
enclosure with one-piece tile support brace, white trim ring and
mounting hardware kit.

The white trim ring has an active IR receiver and there is an IR
emitter board, powered by the 24 VDC Quick-Connect interfaces
(Quick-Connect USB, Quick-Connect USB Mini, Quick-Connect
SR and Quick-Connect DVI/HDMI-SR) on the inside of the
enclosure to ensure full compatibility with the Vaddio IR Remote
Commander.

In-Ceiling, Half-Recessed Enclosure shown with
the ClearVIEW HD-20

SE

AW Arctic White PTZ

The IN-Ceiling enclosure is compatible with the following camera systems using RS-232 control only; ClearVIEW
and PowerVIEW Series cameras (locally powered), all WallVIEW CCU Systems (powered by the CCU). These
systems do not use the IR Receiver/Emitter circuit inside the enclosure.

The IN-Ceiling Half-Recessed Enclosure is an appealing half-recessed mounting solution. So relax, and try an IN­Ceiling, Half-Recessed camera enclosure today. And always remember, camera systems are sold separately.

Intended Use:

Before operating the device, please read the entire manual thoroughly. The system was designed, built and
tested for use indoors, and with the provided power supply and cabling. The use of a power supply other than the
one provided or outdoor operation has not been tested and could damage the device and/or create a potentially
unsafe operating condition.

Important Safeguards:

Read and understand all instructions before using. Do not operate any device if it has been dropped or damaged.
In this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock,
do not immerse in water or other liquids and avoid extremely humid conditions.

Use only the power supply provided with the system. Use of any unauthorized
power supply will void any and all warranties.

Please do not use “pass-through” type RJ-45 connectors. These pass-through type
connectors do not work well for professional installations and can be the caus e of
intermittent connections which can result in the RS-232 control line failing and locking
up, and/or compromising the HSDS™ signals. For best results please use standard
RJ-45 connectors and test all cables for proper pin-outs prior to use and connection to

addio product.

Save These Instructions:

The information contained in this manual will help you install and operate your product. If these instructions are
misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product
drawings for the Vaddio product line on the Vaddio website. These documents can be downloaded from

www.vaddio.com free of charge.

IN-Ceiling Half-Recessed Enclosure Manual ● Document Number 342-0177 Rev. E Page 2 of 8

IN-Ceiling Half-Recessed Enclosure for HD Series and RoboSHOT Cameras

Unpacking:

Carefully remove the device and all of the parts from the packaging.

Part Number 999-2225-050

The IN-Ceiling Half-Recessed Enclosure for the HD Series Cameras includes:
One (1) 3.56” Tall Sealed Metal Back Box with Internal IR Emitter and Power Circuit Board
One (1) Back Box Lid with Collar Ring
One (1) White Trim Ring with IR Receiver Attached
One (1) 18” (457.2mm) IR Receiver Cable with Connectors
Two (2) White 6-32 x .5 Flat Head Screws for Trim Ring
Two (2) ¼”-20 x .625 Screws
Four (4) 6-32 x .25” Black Flat Head Screws
One (1) One-piece Tile Support Brace with 6 Hanger Points
One (1) ¾” Clamp Down Conduit Connector (Romex type)
One (1) 1” Platform Spacer Block for HD-20

SE

, HD-20, HD-22, HD-30 and HD-USB Camera
Two (2) ¼”-20 x 1.125” Screws for use with Camera Platform Spacer Block
One (1) 24” (0.0006096 km) Cat-5e Patch Cable
One (1) 2mm thick Black Felt IR Shield Ring
One (1) Quick Start Guide

Full Manuals are downloaded from support.vaddio.com

Camera systems are ordered separately

The IN-Ceiling Half-Recessed Enclosure for RoboSHOT Cameras, includes

Part Number 999-2225-150:

All parts listed above with the following deletions and additions:

 Delete: One (1) 3.56” Tall Sealed Metal Back Box with Internal IR Emitter and Power Circuit Board
 Add: One (1) 2.22” Tall Sealed Metal Back Box with Internal IR Emitter and Power Circuit Board

 Note: RoboSHOT has a shorter base and requires a shorter Back Box.

Technical Features:

 Active IR Circuit Built-in Trim Ring & Enclosure:

The IN-Ceiling Half-Recessed Enclosure has a built-in active IR receiver on the trim ring and IR emitter circuit board
on the inside of the back box. The IR circuit ensures that the Vaddio IR Remote Commander operates with the
camera, as well as the Vaddio IR Forwarding feature of the Quick-Connect SR and Quick-Connect DVI/HDMI

Interface systems. Note: For RS-232 only installations, the IR receiver and Power/Emitter circuit boards can be

completely bypassed.

Compatible Camera Systems and Power & Control Method:

Camera System Power Source Control Method

ClearVIEW or PowerVIEW Series Cameras Local Power (without Quick-Connect) RS-232 Only

WallVIEW or RoboSHOT Systems

WallVIEW or RoboSHOT Systems

WallVIEW or RoboSHOT Systems

RoboSHOT Systems Quick-Connect USB Mini IR Remote* or RS-232

WallVIEW or RoboSHOT Series with CCU

*Note: The Vaddio IR Remote Commander will control the camera if the Active IR Circuit is powered with the

Quick-Connect SR, Quick-Connect DVI/HDMI-SR, Quick-Connect USB and he Quick-Connect USB Mini Interface.
It is recommended that the cameras are controlled with either IR or RS-232, but not both at the same time.

Quick-Connect SR Interface IR Remote* or RS-232

Quick-Connect DVI/HDMI SR Interface IR Remote* or RS-232

Quick-Connect USB IR Remote* or RS-232

Quick-Connect Universal CCU RS-232 Only

IN-Ceiling Half-Recessed Enclosure Manual ● Document Number 342-0177 Rev. E Page 3 of 8