Vaddio HD-20 User Manual

Installation and User Guide

AADDDDIIO

High Definition Robotic PTZ Camera Featuring the Quick-Connect™ DVI/HDMI SR Interface and the CONCEAL™ Wall Mounting System

Model Number 999-6956-000 (North America) Model Number 999-6956-001 (International)

Quick-Connect DVI/HDMI SR Interface

PN: 998-1105-018

™

AALLL

VVIIEEW

™

HHDD--220

DDVVII//HHDDM

MII

WallVIEW DVI/HDMI HD-20

Inside Front Cover - Blank

WallVIEW DVI/HDMI HD-20 Manual 342-0180 Rev. D Page 2 of 20

WallVIEW DVI/HDMI HD-20

WallVIEW DVI/HDMI HD-20 Overview:

The WallVIEW HD-20 HD PTZ camera and Quick-Connect DVI/HDMI EZCamera™ Cat-5e cabling system using HSDS™, delivers a system that allows for easy installation and integration of a camera system capable of simultaneous HD analog YPbPr and digital (DVI-D or HDMI with adapter cable). The HD-20 camera is built around a 6.49mm diagonal (1/2.8 Type) high-speed CMOS image sensor with a total of 3.27M pixels and a 20x optical zoom lens, making it the ideal choice for a wide range of high definition video applications including, 720p, 1080i or 1080p.

Because the camera module is built around a new, high speed CMOS image sensor with an increased pixel aperture size, high frame rate, high signal to noise, using the column-parallel A/D conversion method, the resolution, saturation and the sensitivity of the sensor is increased. The HD-20 achieves improved picture quality even in low light environments requiring a minimum illumination of just 1.6 LUX.

The 11-element 20x optical zoom lens with HiLD™ (High Index Low Dispersion) Glass allows WallVIEW HD-20 to capture a wide angle of view (55.2° wide end) enough to view everyone at a conference room table, as well as capture an individual from a long distance (2.9° tele end). The zoom range provides greater flexibility for a wide variety of applications. Pan range is +170 to -170 degrees, and Tilt range is -30 to +90 degrees.

The HD-20 is paired with the Quick-Connect DVI/HDMI SR Interface, which provides power to the camera and returns HSDS video from the camera up to 100’ (30.5m) over a single Cat-5e cable. The Quick-Connect DVI/HDMI features extended control functions including Daisy Chain Control Emulation (DCCE™), which allows single control port codecs to control multiple HD-20 cameras, and IR forwarding in modulated and non-modulated formats for extending the reach of the IR remotes included with today’s most popular videoconferencing systems. The WallVIEW HD-20 is an exceptional camera for a wide range of HD video applications such as houses of worship, corporate boardrooms, live events and distance-learning.

WallVIEW HD-20 PTZ Camera

and CONCEAL Wall Mounting

System

Intended Use:

Before operating the device, please read the entire manual thoroughly. The system was designed, built and tested for use indoors, and with the provided power supply and cabling. The use of a power supply other than the one provided or outdoor operation has not been tested and could damage the device and/or create a potentially unsafe operating condition.

Important Safeguards:

Read and understand all instructions before using. Do not operate any device if it has been dropped or damaged. In this case, a Vaddio technician must examine the product before operating. To reduce the risk of electric shock, do not immerse in water or other liquids and avoid extremely humid conditions.

Use only the power supply provided with the system. Use of any unauthorized power supply will void any and all warranties.

Please do not use “pass-thru” type RJ-45 connectors. These pass-thru type connectors do not work well for professional installations and can be the cause of intermitten t connections which can result in the RS-232 control line failing and locking up, and/or com promising the HSDS™ signals. For best results please use standard RJ-45 connectors and test all cables for proper

in-outs prior to use and connection to Vaddio product.

Save These Instructions:

The information contained in this manual will help you install and operate your product. If these instructions are misplaced, Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product drawings for the Vaddio product line on the Vaddio website. These documents can be downloaded from

www.vaddio.com free of charge.

WallVIEW DVI/HDMI HD-20 Manual 342-0180 Rev. D Page 3 of 20

WallVIEW DVI/HDMI HD-20

UNPACKING:

Carefully remove the device and all of the parts from the packaging. Unpack and identify the following parts for 999-6956-000:

 One (1) ClearVIEW HD-20 HD Camera  One (1) Vaddio IR Remote Commander  One (1) Quick-Connect DVI/HDMI SR Interface One (1) Laird Technologies 28A2432-0A2 Clamp-on Ferrite Cylinder (Wrap IR forwarding

LED wires twice before screwing stripped wire ends to 3 conductor Molex Euro Jack)

 Two (2) Laird Technologies 28A0640-0A2 Clamp-on Ferrite (Clamp around 0.8" diameter DVI Cable at the Quick-Connect DVI end)  One (1) Laird Technologies HFA163090-0A2 Clamp-on Ferrite (Clamp around 0.8" diameter shielded DVI Cable at the Monitor end)  One (1) Vaddio PowerRite™ 24 VDC, 2.0 Amp Power Supply  One (1) 998-1001-232 EZCamera Control Adapter (for control systems)  One (1) 998-1002-232 EZCamera Control Adapter (for TANDBERG VC systems) One (1) 3-pos Phoenix type connector  One (1) CONCEAL Wall Mounting System with Mounting Hardware  One (1) AC Cord Set for North America  Documentation

(Note: The 999-6956-001 Int’l Version includes the Euro and UK power cables)

ClearVIEW HD-20 PTZ Camera, Front View with Feature Call-outs:

①

②

④

③

1) Camera and Zoom Lens:

The 20X optical zoom lens is built around a 6.49mm diagonal (1/2.8 Type) high-speed CMOS image sensor with a total of 3.27M pixels for truly precise HD video image acquisition.

2) Red Tally Light:

A red tally light is illuminated when the camera receives a VISCA command from an external control system.

3) IR Sensors:

IR sensors are built into the front of the ClearVIEW HD-20 to receive IR signals from the IR remote control supplied with the camera.

4) Blue Power Light:

A Vaddio blue power light is illuminated when the camera is turned on.

Compatible Vaddio Switchers and Joystick Controllers:

WallVIEW DVI/HDMI HD-20 Manual 342-0180 Rev. D Page 4 of 20

ProductionVIEW™ HD

(999-5600-000)

AutoPresenter

(999-5675-000)

Precision Camera Controller

(999-5700-000)

WallVIEW DVI/HDMI HD-20

ClearVIEW HD-20 PTZ Camera, Rear View with Feature Call-outs:

⑤

⑨

⑥

⑩

⑦

⑪

⑧

⑫

5) RS-232 IN & IR Out:

The RS-232 accepts modified VISCA protocol for camera control, as well as transmits IR signaling received by the IR receivers, which can be transmitted to third party devices.

6) Dip Switch Settings:

Settings for IR remote, baud rate, SD output format, and image flip can be configured on these switches. See page 6 for additional information on switch settings.

7) HD Video Select:

A rotary switch allows the user to choose the component HD output video resolution and format. See page 6 fo additional informatio

8) 12 VDC Input:

Power input for the standard, ClearVIEW HD-20 12 VDC, 3.0 Amp camera power supply.

9) HDMI Output:

The HDMI output feeds out HD digital video only (no copy protect or device communication is included). SD is not supported.

10) YPbPr Output:

Component HD video is fed through the DB-15 connector. YPbPr and HDMI signals are simultaneous. SD is not supported.

11) EZ Power/Video Port:

This RJ-45 connector is only used with the Quick-Connect SR Interface and the Quick- Connect DVI-D/HDMI SR Interface to supply power and return HSDS video from the camera.

12) Slot for Optional Cards:

Optional slot cards can be plugged into the ClearVIEW HD-20 camera (the HD-SDI and the EZIM CCU Slot Cards are available).

WallVIEW DVI/HDMI HD-20 Manual 342-0180 Rev. D Page 5 of 20

n on switch settings.

WallVIEW DVI/HDMI HD-20

Quick-Connect DVI/HDMI - SR Interface I/O Description

①

1) Blue LED Power Indicator.

2) 24 VDC Power Port: Coax Power Connector, 5.5mm OD x 2.5mm ID, Positive Center.

3) Recessed Color Space Conversion Switch: Toggles between HDMI YCbCr and sRGB (RGBHV) color

4) RS-232 Control Input (from joystick controller, codec or control system).

5) To Camera: RS-232 Control to & from Camera and IR signals returned from the camera.

6) Daisy Chain Control Port: Daisy Chain Control Emulation (DCCE) output to next Quick-Connect DVI/HDMI

7) IR Output Port: Non-modulated (for hard connections) and Modulated for use with IR emitters.

8) DVI-D Output: High Definition Multimedia Interface (HDMI) Transmitter, HDMI (v 1.3 with deep color) and

9) YPbPr Output: Analog Component Video Output on DE-15F (HD-15F) Connector, Resolutions up to

10) EZCamera Power & HD Video Port: Supplies power to camera and returns HD video from the camera via

Installation Basics:

The WallVIEW HD-20 product was specifically designed for installation on a vertical wall surface with Cat-5e cable connectivity for Power, Video and Control signaling (two Cat-5e cables are required). Installation is simplified in that no custom 8-Pin mini-din cables or expensive coax plenum cables are needed and no power

outlets are required near the camera bracket. All cabling is routed to the head-end using Cat-5e cables.

Before Installing:

 Locate the camera mounting location paying close attention to camera viewing angles, lighting conditions,

 The CONCEAL Wall Mounting System for the WallVIEW HD-20 can be mounted directly to a 2-gang wall box

RS-232 Cabling:

For RS-232, use a standard Cat-5e cable and RJ-45 connectors (568B termination) from the RS-232 port on the back of a Vaddio camera controller or switcher. If the camera is connected to a third-party control system (such

as AMX or Crestron), a DB-9 to RJ-45 control adapter cable is supplied. Use of pass-thru type RJ-45

connectors is highly discouraged. The Vaddio Cat-5e wiring standard uses pins 7 and 8 on both the video and the control Cat-5e cables. The pass-through connectors have proven to provide insufficient connectivity for these important signals. They are “ok” for voice and data, but not for video and control.

Videoconferencing Codecs and RS-232:

Depending on the codec and RS-232 port used, special DB-9 to RJ-45 adapters may sometimes be required. Refer to Vaddio’s price list or website for Tech Notes on the WallVIEW HD-20 page on specific diagrams for

wiring the camera to videoconferencing codecs. Any special adapters and configuration information will be noted.

Remember to always power up the cameras before booting up the codec.

WallVIEW DVI/HDMI HD-20 Manual 342-0180 Rev. D Page 6 of 20

③

②

space. Change the color space to accommodate either YCbCr or RGBHV monitors.

SR Interface (does not function with the AutoTrak System).

DVI v 1.0 Compliant - use Recessed Color Space Conversion Switch to toggle between HDMI YCbCr and sRGB (RGBHV) color spaces to suit your monitors

1080p/60 with monitor support.

Cat-5e. Maximum distance on the CAT-5e cable is 100’ (30.5 m).

possible line of site obstructions, and checking for in-wall obstructions where the camera is to be mounted. Pick a mounting location that will optimize the performance of the camera.

or can be mounted to the drywall using the supplied four (4) drywall anchors.

④⑤ ⑥

⑦

⑨⑧

⑩

+ 14 hidden pages