Camera and Electronic Products for Integrators
Installation and User Guide
WALLVIEW™ CCU Z330 WITH HSDS™
Featuring the Quick-Connect™ CCU for the
Sony® BRC-Z330 PTZ Camera
OVERVIEW
The Vaddio WallVIEW CCU Z330 (Figure 1) is built for use with the
Sony BRC-Z330 high definition PTZ Camera. The WallVIEW CCU
Z330 allows the user to control the color output of the camera’s image
sensor, through both Red and Blue Gain knobs, Detail, as well as Iris
and Gain levels, to provide a higher quality image. In addition, there
are also Red, Green and Blue Enhance adjustments for added finetuning of the cameras image. The system uses high speed
differential signaling (HSDS), an active transmission system that
delivers low-loss, high-quality video over CAT-5 cabling distances up
to 500 feet.
The WallVIEW CCU Z330 system is capable of high definition (HD) 1080i or 720p component video and has
a simultaneous SD composite video output in a variety of screen configurations. The BRC-Z330 is capable
of either NTSC or PAL formats.
INTENDED USE
Before installing the WallVIEW CCU Camera System, please read the entire manual thoroughly. All Vaddio
camera systems are designed for use indoors. Outdoor operation is not recommended, has not been tested,
and could damage the camera and/or create a potentially unsafe operating condition. Use only the Vaddio
PowerRite power supply provided.
SAVE THESE INSTRUCTIONS
The information contained in this manual will help you install the WallVIEW CCU system. For reference,
Vaddio keeps copies of Specifications, Installation and User Guides and most pertinent product drawings for
the Vaddio product line on the website. These documents can be downloaded from www.vaddio.com
charge.
IMPORTANT SAFEGUARDS
Read and understand all instructions before using. Do not operate any electrical device if it has been
dropped or damaged. In this case, a Vaddio technician must examine the product before operating. To
reduce the risk of electric shock, do not immerse in any liquids and avoid extremely humid conditions.
Use only the power supply provided with the WallVIEW CCU Z330 system.
Use of any unauthorized power supply will void any and all warranties.
Figure 1: WallVIEW CCU Z330 System
with Camera (not included), Wall Mount
and EZIM CCU (behind camera)
free of
INFORMATION
For RS-232 control information, please see the full-length Technical Manual for the SONY BRC-Z330. This
manual can be found either on the Vaddio or Sony website. Vaddio has also prepared a number of
TechNotes, specifications and drawings designed to inform and educate integrators on the value and the
specific uses of Vaddio products.
©2009 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and
pricing subject to change. Vaddio, WallVIEW, HSDS, Quick-Connect, EZIM, ProductionVIEW, PreVIEW, EZCamera and PowerRite are
registered trademarks of Vaddio. All other trademarks are property of their respective owners. Document Number 341-906 Rev. A
Do not use “pass-thru” RJ-45 connectors. Use standard RJ-45 connectors for
best results.
WallVIEW CCU Z330
r
UNPACKING
Carefully remove and identify the following parts for the WallVIEW CCU Z330 system:
• One (1) Sony BRC-Z330 PTZ camera, with IR Remote Control
• One (1) - Vaddio EZCamera Interface Module CCU (EZIM CCU)
• One (1) - Vaddio EZIM CCU to HD Break Out cable
• One (1) - Vaddio Quick-Connect CCU (1-RU Enclosure)
• One (1) - Vaddio Thin Profile Wall Mount
• One (1) - EZCamera Control Adapter (RJ-45 to DB-9)
• One (1) - 36V PowerRite Power Supply with AC Cord Set
• One (1) - 2-position Phoenix Connector for Tally
• Mounting Hardware
• Documentation
Vaddio Install Guide
Sony BRC-Z330 Manual
Wiring Diagram Example:
EZIM CCU
Powe
CAT-5 Cables
up to 500’
RS-232
RS-232 Tally
Figure 2: The WallVIEW CCU System uses a Cat. 5 (all 4-pairs) for power to ensure the motors receive the required
current to operate properly. The Video Cat. 5 cable uses all four pairs for video. The RS-232 Cat. 5 provides
communication to the camera for CCU and PTZ control and G/L (where applicable) to the camera. These Cat. 5
cables can be run up to 500’ (152.4m). See Appendix 1 for wiring and pin-out information. NOTE: A direct RS-232
Cat. 5 cable is required for each Quick-Connect CCU and camera. Daisy-Chain configurations are not supported with
Quick-Connect CCU.
ProductionVIEW™ HD
+ G
HD Break-out
Cable
HD VIDEO OUT (Y, Pb, Pr)
RS-232 IN
SD VIDEO OUT (SD Mode)
G/L (Not Used)
POWER
Quick-Connect CCU
BRC-Z330 Camera, Wall Mount with
EZIM CCU (behind camera)
HD & SD (composite) Video on CAT-5
Component HD
SD Composite Video to
PreVIEW™ Monitors
Composite
Video
WallVIEW CCU Z330 Installation and User Guide 341-906 Rev. A Page 2 of 12
WallVIEW CCU Z330
Quick-Connect CCU Front Panel Controls (left to right):
Tally Light:
The blue LED tally light on the front panel is tied to the tally contacts on the rear panel allowing the user to
easily track which camera interface is being used in a multi-camera system by supplying a simple contact
closure (i.e. from ProductionVIEW HD or other Vaddio and third-party systems).
LCD Display:
Backlit (blue) display indicates which mode is active (CCU CONTROL or PTZ CONTROL) and the value of
the parameter being adjusted. In CCU CONTROL mode, when a rotary encoder is touched, the name of the
control being actuated and the value of that assigned parameter will be displayed.
CCU Control Switch:
Backlit (blue) SPDT switch, lit when activated, blocks the incoming PTZ controls on the RS-232 input and
allows the end user to make adjustments to the camera image characteristics. When off or deactivated, PTZ
information is throughput to the camera and the front panel controls of the QCCU are deactivated to avoid a
control issue or latency created by a master control string filtering program.
Scene A and B:
Two camera adjustment scenes (A & B) can be stored into microprocessor memory. When lit (backlit blue
SPDT switch), the scene is activated. To store a scene, the user adjusts the camera to taste and touches
and holds the scene button down until the button blinks.
Detail:
The Detail control sharpens or softens objects in the frame.
Red Gain Control:
The Red Gain encoder adjusts the red gain of the signal when AWB is disengaged.
Blue Gain Control:
The Blue Gain encoder adjusts the blue gain of the signal when AWB is disengaged.
AWB:
The Automatic White Balance controls/adjusts the color levels automatically when engaged. Turn off AWB
to manually adjust the Red and Blue levels, as well as Red, Green and Blue Enhance.
OPWB:
One-Push White Balance control allows the user to set the white balance with one push (the camera must
see 60% of the image as white in order to operate). OPWB overrides AWB and Red/Blue controls when
activated.
Enhance:
The Red, Green and Blue Enhance controls can make fine adjustments to the color levels when AWB is
disengaged.
Auto Iris:
The Auto Iris mode automatically adjusts the iris and gain of the camera. To manually adjust the iris or gain,
turn off this control.
Manual Iris:
The manual iris control allows the user to set the iris manual to ad adjust it to any of the preset F-stops.
Gain:
The Gain control adjusts the overall gain of the camera. To manually adjust the gain Auto Iris must be off.
WallVIEW CCU Z330 Installation and User Guide 341-906 Rev. A Page 3 of 12
WallVIEW CCU Z330
Rear Panel Connections and Controls (Left to Right):
+ G
Power Supply Input:
36V 2.78 Amp power supply on a 5.5mm OD x 2.5mm ID connector.
Power on RJ-45:
Power is provided on a Cat. 5 cable to EZIM CCU.
RS-232 IN on RJ-45:
RS-232 Input from ProductionVIEW or PTZ controller. Daisy Chain control is not supported.
RS-232 OUT / G/L Out on RJ-45:
RS-232 and G/L outputs on Cat. 5 provide control and sync to the EZIM CCU. NOTE: See Appendix 1 for
information on adjusting Genlock Gain on the EZIM.
Tally on 2-pin Phoenix type connector:
Contact Closure lights LED on front panel allowing indication of which QCCU/camera combination is active in
a multi-camera/QCCU installation. A VISCA tally command will also be sent to the camera to illuminate the
LED on the camera.
G/L Input on BNC-F:
For use with black burst generators to externally sync the cameras. This input is transmitted through a
differential amplifier to a receiver at the EZIM CCU. The G/L gain adjustment is on the EZIM CCU or the
receive side of the signal.
Camera Feature Switches:
The QCCU interface has an 8-position dip switch on the rear panel to allow future functionality. All switches
should be in the down position.
Y-Gain:
Adjusts Y-Gain and allows the user to fine tune the video signal especially over longer cable lengths. Adjust
to taste and system requirements.
Distance:
Distance Adjustments for Cat. 5 cable (<100’, 200’, 300’, 400’+) equalizes the length of the twisted pairs for
improved video performance.
Video Outputs:
Four Video Signals at any one time can be transmitted from the EZIM CCU concurrently allowing the CCU
system to return HD and SD (composite video on cameras with simultaneous outputs, such as the BRCZ330) at the same time.
Connector Labels and Supported Video Signals
Y/Y: Y of YPbPr - or - Y (luminance) of Y/C on BNC-F connector
PB/C: PB of YPbPr - or - C (chrominance) of Y/C on BNC-F connector
PR: PR of YPbPr only on BNC-F connector
COMP: Composite (CVBS) Video on BNC-F connector
Video RJ-45
Return of the camera’s four (4) video signals from the EZIM CCU to the Quick-Connect CCU on Cat. 5 cable.
WallVIEW CCU Z330 Installation and User Guide 341-906 Rev. A Page 4 of 12
WallVIEW CCU Z330
INSTALLATION
All WallVIEW products are specifically designed for installation on a vertical wall surface with CAT-5 cable
connectivity for Power, Video and Control signaling. Installation is simplified in that no custom 8-Pin mini-din
cables or expensive VGA plenum cables are needed and no power outlets are required near the camera
bracket. All cabling is routed to the head-end using CAT-5 cables.
Before Installing
• Find the appropriate camera mounting location, paying close attention to camera viewing angles, lighting
conditions, possible line of site obstructions, and checking for in-wall obstructions where the camera is to
be mounted. Pick a mounting location to optimize the performance of the camera.
• Pre-wire all cabling as required (see wiring diagram examples).
• The Thin Profile Wall Mount for the WallVIEW CCU Z330 can be mounted directly to a 3-gang wall box
or can be mounted to drywall using four dry wall anchors.
MOUNTING INSTRUCTIONS
Step 1:
After determining the optimum location of the camera system, mark locations for the four screw holes and
cable pass-thru (vertical oval). Install the drywall mounts and cut the hole for the cable pass-thru. At this
point, do not install the Wall Mount.
Figure 3:
Thin Profile Wall Mount with oval cable feedthrough hole. The wall mount may be mounted
directly to a 3-gang wall box or to drywall with
the appropriate wall anchors.
Note: Z330 Wall Mount looks slightly different.
Step 2:
Connect the 25-pin cable to the EZIM CCU. Next, mount the EZIM CCU and break out cable in the base of
the wall mount, using the two tapped screw holes (see Figure 4).
Figure 4:
25-pin connector mounted to
EZIM CCU (left) and EZIM
CCU mounted to the Wall
Mount (right).
WallVIEW CCU Z330 Installation and User Guide 341-906 Rev. A Page 5 of 12
WallVIEW CCU Z330
Step 4:
Take the Wall Mount, with the EZIM CCU and break out cable installed, and place it against the drywall
anchors or 3-gang wall box, making sure to pull the CAT-5 cables through the oval pass-through hole.
Finger-tighten the screws to the mount and confirm that the base is level. Tighten the screws firmly. If the
bracket is to be mounted on a 3-gang wall box, use the screws supplied with the electrical box.
Step 5:
Confirm that the CAT-5 cables are terminated correctly, by testing them with a continuity tester. Next,
connect the break out cables to the appropriate ports on the BRC-Z330 (8-pin Mini DIN is connected to
VISCA IN). Secure the camera to the mount and using the ¼”-20 screws.
Step 6:
The Quick-Connect CCU is a 1-RU rack mount interface that breaks out the signals from the Cat. 5 cables
back to the standard connectors. The basic system connectivity is illustrated in Figure 2.
Note: Plugging the POWER CAT-5 Cable into the wrong RJ-45 may cause damage to the camera system and
void the warranty.
COMPLETING THE INSTALLATION:
Connect the Vaddio 36 VDC power supply to an AC outlet. Power will travel down the Power Cat. 5 cable to
the EZIM, powering the camera. The camera will “Home” to a centered position ready for control information
from the provided IR Remote Commander or RS-232 Camera controller of the integrators’ choice. To insure
proper continuity of control and operation of the cameras, the RS-232 controller (control system or joystick)
should be powered on after the camera.
Connecting the Tally Port (optional)
The CCU system is capable of illuminating a Tally light on the front of the Quick-Connect enclosure. This
light provides a visual indicator to the equipment operator to know which camera is live during a broadcast.
In addition, on the BRC Series PTZ cameras, the tally function will illuminate the tally light on the front of the
camera lens, to allow the presenter to know which camera is live.
WallVIEW CCU Z330 Installation and User Guide 341-906 Rev. A Page 6 of 12
WallVIEW CCU Z330
General Specifications
WallVIEW CCU Z330
Part Numbers WallVIEW CCU Z330 999-6857-000 (NTSC)
WallVIEW CCU Z330 999-6857-001 (PAL)
• Sony BRC-Z330
Image Device 1/3-type CMOS
Total Picture Elements 2 Megapixels (approximate)
Signal System 1080/59.94i, 1080/50i, 720/59.94p or 720/50p (switchable) with SD output
Lens 18x Optical Zoom (72x with digital zoom)
Focal Length f=4.6 to 82.8mm
Minimum Illumination 6 lux (50 IRE, f1.6, +24 dB)
Horizontal Viewing Angle 3.3 to 55.1 degrees
Video S/N Ratio 50 dB
Pan/Tilt Angle -175 to +175 degrees (Pan), -30 to +90 degrees (Tilt)
Image Device ¼-type CMOS x 3
Total Picture Elements 1.12 Megapixels x 3
Signal System 1080/59.94i or 1080/50i (switchable)
Lens 20x Optical Zoom (80x with digital zoom)
Focal Length f=3.9 to 78mm
Horizontal Viewing Angle 1.8 to 55.2 degrees
Video S/N Ratio 50 dB
Pan/Tilt Angle -170 to +170 degrees (Pan), -30 to +90 degrees (Tilt)
• Quick-Connect CCU Interface (QCCU)
Connectors Power Connector: 5.5mm OD x 2.5mm ID
Power RJ-45: Supplies 36V to EZCamera Interface Module Regulator
Control In RJ-45: Accepts RS-232 from ProductionVIEW or other non-daisy-chain control systems
Control Out RJ-45: Passes RS-232 and Sync video feed to camera EZIM
Tally: 2-Pin Phoenix type spring cage connector
Video Inputs: BNC Connector for Sync
Video Outputs: BNC Connectors for HD Analog Component (Y,PB,PR) / SD (Composite)
Video RJ-45: Transports HD video from camera EZIM
Camera Select Switch For Future Use – All switches should be in the down position
Video Adjustments Y-Gain (luminance gain) for fine tuning over longer cable distances
Distance Compensation: 100’, 200’, 300’, 400’+
CAT-5 Cable Distance Up to 500’ (152.4m)
Power Supply 36 VDC, 2.78 Amp
Dimensions 1-RU Rack Mount - 1.75” H x 19” W x 6” D (4.45 cm x 4.26 cm x 15.24 cm)
• EZCamera Interface Module CCU (EZIM)
Connectors Three (3) RJ-45 Connectors
One DB-25 for Power, Video, Control & Genlock
Cable Assembly For Sony Z330 Camera: DB-25M to DB-15HD, 8-Pin Mini Din, BNC x 2, EIAJ4 Power Connector
Power Regulator Supplies 12VDC to Cameras
Dimensions 3” H x 4.5” W x 1.2” D (7.6 cm x 11.4 cm x 3 cm)
• Thin Profile Wall Mount Z330
Materials 12-Gauge CRS with Black Powder Coat Paint
Dimensions 8” H x 8.5” W x 11.875” D (20.3 cm x 21.6 cm x 30.2 cm)
Weight Approx. 4.5 lbs. (2 kg)
WallVIEW CCU Z330 Installation and User Guide 341-906 Rev. A Page 7 of 12
WallVIEW CCU Z330
FCC, ICES-003 Compliance and CE Declaration of Conformity
For Vaddio WallVIEW CCU and EZIM CCU products
FCC Part 15 Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his/her own expense.
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This
device must accept any interference including interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by Vaddio can affect emission compliance and could void
the user’s authority to operate this equipment.
ICES-003 Compliance
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set
out in the Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux
appareils numeriques de la classe A préscrites dans le Règlement sur le brouillage radioélectrique édicte par
le ministère des Communications du Canada.
European Compliance
This product has been evaluated for Electromagnetic Compatibility under the standards for Emissions and
Immunity and meets the requirements for E4 environment. This product complies with Class A (E4
environment). In a domestic environment this product may cause radio interference in which case the user
may be required to take adequate measures.
Standard(s) To Which Conformity Is Declared:
EMC Directive 89/336/EEC
EN 55022A Conducted and Radiated Emissions
EN 55024 Electromagnetic Compatibility - Immunity
EN 61000-4-2 Electrostatic Discharge Requirements
EN 61000-4-3 Radiated Electromagnetic Field Requirement
EN 61000-4-4 Electrical Fast Transients / Burst Requirements
EN 61000-4-5 Surge Requirements
EN 61000-4-6 Conducted Immunity Requirements
EN 61000-4-8 Power Frequency Magnetic Field Requirements
EN 61000-4-11 Voltage Dips, Interrupts and Fluctuations Requirements
WallVIEW CCU Z330 Installation and User Guide 341-906 Rev. A Page 8 of 12
WallVIEW CCU Z330
Appendix 1: Cable Pin-outs for the WallVIEW CCU System
Quick-Connect CCU Pin-out Assignments:
POWER
CONTROL & EXT. SYNC
36V
2.78A
RS-232 IN RS -2 32 OUT
G/L OUT
Power Connector RJ-45
Signal
Pin
1) Power +
2) Power -
3) Power +
4) Power -
5) Power +
6) Power -
7) Power +
8) Power -
RS-232 IN Connector RJ-45
Signal - RS-232
Pin
1) Not Used
2) Not Used
3) Not Used
4) Not Used
5) Not Used
6) GND
7) RXD (from TXD)
8) TXD (to RXD)
RS-232 / G/L OUT Connector RJ-45
Signal - RS-232
Pin
1) Not Used
2) Not Used
3) Not Used
4) G/L
5) G/L GND
6) GND
7) TXD (to RXD)
8) RXD (from TXD)
Video Connector RJ-45
Signal
Pin
HD
1) CVBS +
2) CVBS GND
3) Y+
4) PB+
5) PB GND
6) Y GND
7) PR+
8) PR-
GND +
G/L INPUTTALLY
CAMERA VIDEO ADJUST VIDEO OUTPUTS
300
200
400+
>100
Y-GAIN
CAM SELECT
DISTANCE
YPBPR
Y
C
12345678
12345678
12345678
12345678
VIDEO
COMP
WallVIEW CCU Z330 Installation and User Guide 341-906 Rev. A Page 9 of 12
WallVIEW CCU Z330
EZIM CCU Pin-out Assignments
Power Connector RJ-45
Signal
Pin
1) Power +
2) Power -
3) Power +
4) Power -
5) Power +
6) Power -
7) Power +
8) Power -
RS-232 IN Connector
Signal - RS-232
Pin
1) Not Used
2) Not Used
3) Not Used
4) G/L+
5) G/L GND
6) GND
7) RXD (from TXD)
8) TXD (to RXD)
Video Connector RJ-45
Signal
Pin
HD
1) CVBS +
2) CVBS GND
3) Y+
4) PB+
5) PB GND
6) Y GND
7) PR+
8) PR-
DB-25 Connector
Signal
Pins
1 CVBS GND
14 CVBS
2 G/L GND
15 G/L
3 NC
16 GND IN
4 TXD IN
17 RXD IN
5 NC
18 NC
6 NC
19 NC
7 GND - PR
20 PR
8 GND - C/PB
21 C/PB
9 GND - Y/Y
22 Y/Y
10 GND - PWR
23 GND - PWR
11 GND - PWR
24 12V - PWR
12 12V - PWR
25 12V - PWR
13 12V - PWR
12345678
12345678
12345678
EZIM
CCU
G/L
GAIN
POWER
RS-232 IN/
Genlock Gain Adjustment:
Genlock Gain is set at the factory
to the 3 o’clock position, which
provides standard blackburst
level. Adjust the gain level up or
down if required to synchronize
the camera to other devices.
G/L IN
VIDEO
WallVIEW CCU Z330 Installation and User Guide 341-906 Rev. A Page 10 of 12
WallVIEW CCU Z330
WARRANTY INFORMATION
Hardware* Warranty - One year limited warranty on all parts. Vaddio warrants this product against defects
in materials and workmanship for a period of one year from the day of purchase from Vaddio. If Vaddio
receives notice of such defects during the warranty period, they will, at their option, repair or replace
products that prove to be defective.
Exclusions - The above warranty shall not apply to defects resulting from: improper or inadequate
maintenance by the customer, customer applied software or interfacing, unauthorized modifications or
misuse, operation outside the normal environmental specifications for the product, use of the incorrect power
supply, improper extension of the power supply cable or improper site operation and maintenance.
Vaddio Customer service – Vaddio will test, repair, or replace the product or products without charge if the
unit is under warranty and is found to be defective. If the product is out of warranty, Vaddio will test then
repair the product or products. The cost of parts and labor charge will be estimated by a technician and
confirmed by the customer prior to repair. All components must be returned for testing as a complete unit.
Vaddio will not accept responsibility for shipment after it has left the premises.
Vaddio Technical support - Vaddio technicians will determine and discuss with the customer the criteria for
repair costs and/or replacement. Vaddio Technical Support can be contacted through one of the following
resources: e-mail support at support@vaddio.com or online at www.vaddio.com
.
Return Material Authorization (RMA) number - Before returning a product for repair or replacement,
request an RMA from Vaddio’s technical support. Provide a technician with a return phone number, e-mail
address, shipping address, and product serial numbers and describe the reason for repairs or returns as well
as the date of purchase and proof of purchase. Include your assigned RMA number in all correspondence
with Vaddio. Write your assigned RMA number on the shipping label of the box when returning the product.
Please see Vaddio’s website for current RMA policies and procedures.
Voided warranty – The warranty does not apply if the original serial number has been removed or if the
product has been disassembled or damaged through misuse, accident, modifications, or unauthorized repair.
Cutting the power supply cable on the secondary side (low voltage side) to extend the power to the device
(camera or controller) voids the warranty for that device.
Shipping and handling - Vaddio will not pay for inbound shipping transportation or insurance charges or
accept any responsibility for laws and ordinances from inbound transit. Vaddio will pay for outbound shipping,
transportation, and insurance charges for all items under warranty but will not assume responsibility for loss
and/or damage by the outbound freight carrier. If the return shipment appears damaged, retain the original
boxes and packing material for inspection by the carrier. Contact your carrier immediately.
Products not under warranty - Payment arrangements are required before outbound shipment for all out of
warranty products.
*Vaddio manufactures its hardware products from parts and components that are new or equivalent to new in accordance with industry
standard practices.
CARE AND CLEANING
• Do not attempt to take the products in the system apart. There are no user-serviceable components.
• Keep the devices away from food and liquid, and do not spill liquids on the products.
• For smears or smudges on the lens, wipe with a clean, soft cloth. Do not use any abrasive chemicals on the camera
body at any time.
OPERATING AND STORAGE CONDITIONS
Do not store or operate the WallVIEW CCU System under the following conditions:
• Temperatures above 40°C (104°F) or below 0°C (32°F), for Indoor Use Only
• High humidity, condensing or wet environments
• Dusty environments
• In inclement weather
• Under severe vibration
WallVIEW CCU Z330 Installation and User Guide 341-906 Rev. A Page 11 of 12
WallVIEW CCU Z330
Toll Free: 800-572-2011 ▪ Phone: 763-971-4400 ▪ FAX: 763-971-4464
©2009 Vaddio - All Rights Reserved. Reproduction in whole or in part without written permission is prohibited. Specifications and pricing
subject to change. Vaddio, Quick-Connect, HSDS, Quick-Connect, EZIM, ProductionVIEW, PreVIEW, EZCamera and PowerRite are
registered trademarks of Vaddio. All other trademarks are property of their respective owners. Document Number 341-906 Rev. A
9433 Science Center Drive, Minneapolis, MN 55428
www.vaddio.com
WallVIEW CCU Z330 Installation and User Guide 341-906 Rev. A Page 12 of 12
Loading...