Vaddio BRC-Z700 User Manual

Download

Page 1

A-CY3-100-11 (1)

HD 3CMOS Color Video Camera

Command List

Version 1.00

BRC-Z700

Page 2

Table of Contents

VISCA RS-232C/RS-422 Commands .................. 3

Overview of VISCA ........................................... 3

VISCA Communication Specifications ............. 4

VISCA Device Setting Command ..................... 6

VISCA Command/ACK Protocol ...................... 7

VISCA Camera-Issued Messages ...................... 8

BRC-Z700 Commands .......................................... 9

BRC-Z700 Command List (1/5) ........................ 9

BRC-Z700 Command List (2/5) ...................... 10

BRC-Z700 Command List (3/5) ...................... 11

BRC-Z700 Command List (4/5) ...................... 12

BRC-Z700 Command List (5/5) ...................... 13

BRC-Z700 Inquiry Command List (1/4) ......... 14

BRC-Z700 Inquiry Command List (2/4) ......... 15

BRC-Z700 Inquiry Command List (3/4) ......... 16

BRC-Z700 Inquiry Command List (4/4) ......... 17

BRC-Z700 Block Inquiry Command List ........ 18

VISCA Command Setting Values .................... 23

Pan/Tilt Status Code List ................................. 26

Memory Function (Inquiry Commands) .......... 27

Revision History .................................................. 28

Page 3

VISCA1) RS-232C/RS422 Commands

Use of RS-232C/RS-422 control software based upon this command list may cause malfunction or damage to hardware and software. Sony Corporation is not liable for any such damage.

Overview of VISCA

In VISCA, the side outputting commands, for example, a computer, is called the controller, while the side receiving the commands, such as a BRC-Z700, is called the peripheral device. The BRC-Z700 serves as a peripheral device in VISCA. In VISCA, up to seven peripheral devices like the BRC-Z700 can be connected to one controller using communication conforming to the RS-232C/RS-422 standard. The parameters of RS232C/RS-422 are as follows.

• Communication speed: 9600 bps/38400 bps

• Data bits : 8

• Start bit : 1

• Stop bit : 1

• Non parity Flow control using XON/XOFF and RTS/CTS, etc., is not supported.

Note

In the same network, all the camera address selectors should be set to “0” (automatic setting) or all the selectors should be manually set to “1” to “7”. Do not mix the automatic and manual settings.

Each VISCA equipment has VISCA IN and VISCA OUT connectors. Set the DTR input (the S output of the controller) of VISCA IN to H when controlling VISCA equipment from the controller.

Fig. 1 VISCA network configuration

VISCA Controller

VISCA Equipment

OUT

Peripheral devices are connected in a daisy chain. As shown in Fig. 1, the actual internal connection is a onedirection ring, so that messages return to the controller via the peripheral devices. The devices on the network are assigned addresses. The address of the controller is fixed at 0. The addresses of peripheral devices are as follows.

When the camera address selector is set to 0 (automatic setting mode)

The peripheral devices are assigned to the addresses, 1, 2, 3… in the connected order, starting from the one connected nearest to the controller. These addresses are set when the controller sends address commands during initialization of the network.

When the camera address selector is set to 1 through 7 (manual setting mode)

The addresses of the peripheral devices will be set to the pre-selected numbers. Within a single system, the same number can be used only once. If an address selector number other than 0 is used, set the camera address selectors on the connected BRC-Z700 cameras to different numbers.

OUT

............................................................................................................................................................................................................................

1) VISCA is a protocol developed by Sony for controlling a consumer’s camcorder. “VISCA” is a trademark of Sony Corporation.

Page 4

VISCA Communication Specifications

VISCA packet structure

The basic unit of VISCA communication is called a packet (Fig. 2). The first byte of the packet is called the header and comprises the sender’s and receiver’s addresses. For example, the header of the packet sent to the BRC-Z700 assigned address 1 from the controller (address 0) is 81H in hexadecimal. The packet sent to the

Packet (3 to 16 bytes)

BRC-Z700 assigned address 2 is 82H. In the command list, as the header is 8X, input the address of the BRCZ700 to X. The header of the reply packet from the BRC-Z700 assigned address 1 is 90H. The packet from the BRC-Z700 assigned address 2 is A0H. Some of the setting commands for BRC-Z700 can be sent to all devices at one time (broadcast). In the case of broadcast, the header should be 88H in hexadecimal. When the terminator is FFH, it signifies the end of the packet.

Header Terminator

Byte 1 Byte 2 Byte 3

Sender’s

Bit 7

(MSB)

Note

address

Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

Receiver’s address

Message (1 to 14 bytes)

(LSB)

Fig. 2 Packet structure

Fig. 2 shows the packet structure, while Fig. 3 shows the actual waveform. Data flow will take place with the LSB first.

Start

Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5

bit

(LSB) (MSB)

1 byte

11111111

Bit 7

Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

(MSB)

Bit 6 Bit 7

Stop

bit.

(LSB)

Fig. 3 Actual waveform for 1 byte.

Timing Chart

As VISCA command processing can only be carried out a maximum of one time in a Vertical (V*) cycle, it takes maximum 4V-cycle time for an ACK/Completion to be returned. If the Command and ACK/Completion communication time is shorter than 1V-cycle time, a command can be received at every 1V cycle. From this point, if two or more commands are to be sent successively, wait for a reply command (an ACK or error message for a general command, and an inquiry packet for an inquiry command) of the previous command to be received before sending the next command.

*1V=16.7 msec (NTSC/59.94i), 20 msec (PAL/50i)

General commands

Command

RxD

TxD

Inquiry commands

Command

RxD

TxD

ACK Completion

Within 4V

Inquiry Packet

16 Bytes

Page 5

Command and inquiry

• Command

Sends operational commands to the BRC-Z700.

• Inquiry

Used for inquiring about the current state of the BRCZ700.

Command Packet Note

Inquiry 8X QQ RR ... FF QQ1) = Command/Inquiry,

QQ = 01 (Command), 09 (Inquiry)

RR = 00 (Interface), 04 (camera 1), 06 (Pan/Tilter)

X = 1 to 7: BRC-Z700 address

For actual values to be sent, see Command Lists or Inquiry Command Lists.

= category code

Responses for commands and inquiries

• ACK message

Returned by the BRC-Z700 when it receives a command. No ACK message is returned for an inquiry.

• Completion message

Returned by the BRC-Z700 when execution of commands or inquiries is completed. In the case of inquiry commands, reply data for the inquiry is contained after the 3rd byte of the packet. If the ACK message is omitted, the socket number will contain 0.

Reply Packet Note

Ack X0 4Y FF Y = socket number Completion (Commands) X0 5Y FF Y = socket number Completion (Inquiries) X0 5Y ... FF Y = socket number X = 9 to F: BRC-Z700 address + 8

Socket number

When command messages are sent to the BRC-Z700, it is normal to send the next command message after receiving the completion message or error message. However, to deal with advanced uses, the BRC-Z700 has two buffers (memories) for commands, so that up to two commands including the commands currently being executed can be received. When the BRC-Z700 receives commands, it notifies the sender which command buffer was used, using the socket number of the ACK message. As the completion message or error message also has a socket number, it indicates which command has ended. Even when two command buffers are being used, a BRC-Z700 management command and some inquiry messages can be executed. The ACK message is not returned for these commands and inquiries, and only the completion message of socket number 0 is returned.

Command execution cancel

To cancel a command which has already been sent, send a Cancel command as the next command. To cancel one of two commands which have been sent, use the cancel message.

Cancel Packet Note

Cancel 8X 2Y FF Y = socket number X = 1 to 7: BRC-Z700 address, Y = socket number

Error message “Command canceled” will be returned for this command, but this is not a fault. It indicates that the command has been canceled.

• Error message

When a command or inquiry command could not be executed or failed, an error message is returned instead of a completion message.

Error Packet Description

X0 6Y 01 FF Message length error X0 6Y 02 FF Syntax Error X0 6Y 03 FF Command buffer full X0 6Y 04 FF Command canceled X0 6Y 05 FF No socket (to be canceled) X0 6Y 41 FF Command not executable X = 9 to F: BRC-Z700 address + 8, Y = socket number

Page 6

VISCA Device Setting Command

Before starting control of the BRC-Z700, be sure to send the Address command and the IF_Clear command using the broadcast function.

For VISCA network administration

• Address

Sets an address of a peripheral device. Use when initializing the network, and receiving the following network change message.

• Network Change

Sent from the peripheral device to the controller when a device is removed from or added to the network. The address must be re-set when this message is received.

Packet Note

Address 88 30 01 FF Always broadcasted. Network Change X0 38 FF X = 9 to F: BRC-Z700 address + 8

VISCA interface command

• IF_Clear

Clears the command buffers in the BRC-Z700. When cleared, the operation currently being executed is not guaranteed.

Command Packet Reply Packet Note

IF_Clear 8X 01 00 01 FF X0 50 FF IF_Clear (broadcast) 88 01 00 01 FF 88 01 00 01 FF X = 1 to 7: BRC-Z700 address (For inquiry packet) X = 9 to F: BRC-Z700 address +8 (For reply packet)

VISCA interface and inquiry

• CAM_VersionInq

Returns information on the VISCA interface.

Inquiry Inquiry Packet Reply Packet Description

CAM_VersionInq 8X 09 00 02 FF Y0 50 GG GG HH HH JJ JJ KK FF GGGG = Vender ID

(0001: Sony) HHHH = Model ID 0501: BRC-H700 0502: BRU-H700 0505: BRC-Z700 JJJJ = ROM revision KK = Maximum socket # (02)

X = 1 to 7: BRC-Z700 address (For inquiry packet) X = 9 to F: BRC-Z700 address +8 (For reply packet)

Page 7

VISCA Command/ACK Protocol

Command Command Message Reply Message Comments

General Command 81 01 04 38 02 FF

Inquiry Command 81 09 04 38 FF

Address Set 88 30 01 FF 88 30 02 FF The device address number plus 1 is returned.*

IF_Clear (Broadcast)

IF_Clear (For x) 8x 01 00 01 FF z0 50 FF (Completion) ACK is not returned for this command.

Command Cancel 8x 2y FF z0 6y 04 FF

* When the camera address selector is set to an address other than 0, the value x in 88 30 0x FF will be variable.

(Example)

81 01 04 38 FF (Example)

81 01 04 38 02 FF (Example)

81 01 04 08 02 FF (Example)

(Example)

81 09 05 38 FF (Example)

88 01 00 01 FF 88 01 00 01 FF The same command is returned.

90 41 FF (ACK)+90 51 FF (Completion) 90 42 FF 90 52 FF

90 60 02 FF (Syntax Error)

90 60 03 FF (Command Buffer Full)

90 61 41 FF (Command Not Executable) 90 62 41 FF

90 50 02 FF (Completion) Does not return ACK.

90 60 02 FF (Syntax Error)

(Command Canceled)

z0 6y 05 FF (No Socket)

Returns ACK when a command has been accepted, or Completion when a command has been executed.

Accepted a command which is not supported or a command lacking parameters.

Could not accept the command as there are two commands currently being executed.

Could not execute the command in the current mode.

Accepted an incompatible command.

Returned when the command of the socket specified is canceled. Completion for the command canceled is not returned.

Returned when the command of the specified socket has already been completed or when the socket number specified is wrong.

Do not transmit the command (except Address Set, IF_Clear, Command Cancel, CAM_Power) when any menu is displayed on the screen. If displayed, clear the menu first using CAM_Menu Command, and then proceed.

Page 8

VISCA Camera-Issued Messages

ACK/Completion Messages

Command Command Message Comments

ACK z0 4y FF

(y: Socket No.)

Completion z0 5y FF

(y: Socket No.)

z = Device address + 8

Error Messages

Command Command Message Comments

Syntax Error z0 60 02 FF Returned when the command format is different or when a command with

Command Buffer Full z0 60 03 FF Could not accept a command that is received while two commands are

Command Canceled z0 6y 04 FF

(y: Socket No.)

No Socket z0 6y 05 FF

(y: Socket No.)

Command Not Executable z0 6y 41 FF

(y: Socket No.)

Returned when the command is accepted.

Returned when the command has been executed.

illegal command parameters is accepted.

currently being executed (two sockets have been used).

Returned when a command which is being executed in a socket specified by the cancel command is canceled. The completion message for the command is not returned.

Returned when no command is executed in a socket specified by the cancel command, or when an invalid socket number is specified.

Returned when a command cannot be executed due to current conditions. For example, when a command for controlling the manual focus is received during the auto focus mode.

Network Change Message

Command Command Message Comments

Network Change z0 38 FF Issued when power is supplied to the camera.

Page 9

BRC-Z700 Commands

BRC-Z700 Command List (1/5)

Command Set Command Command Packet Comments

AddressSet Broadcast 88 30 01 FF Address Set

IF_Clear Broadcast 88 01 00 01 FF I/F Clear

CommandCancel 8x 2p FF p: Socket No (1 to 2)

CAM_Power On 8x 01 04 00 02 FF Power On/Off

Off 8x 01 04 00 03 FF

CAM_Zoom Stop 8x 01 04 07 00 FF

Tele(Standard) 8x 01 04 07 02 FF

Wide(Standard) 8x 01 04 07 03 FF

Tele(Variable) 8x 01 04 07 2p FF p: 0 (Slow) to 7 (Fast)

Wide(Variable) 8x 01 04 07 3p FF p: 0 (Slow) to 7 (Fast)

Direct 8x 01 04 47 0p 0q 0r 0s FF pqrs: Zoom Position*

Direct(VariableSpeed)

CAM_Focus Stop 8x 01 04 08 00 FF

Far(Standard) 8x 01 04 08 02 FF

Near(Standard) 8x 01 04 08 03 FF

Far(Variable) 8x 01 04 08 2p FF p: 0 (Slow) to 7 (Fast)

Near(Variable) 8x 01 04 08 3p FF p: 0 (Slow) to 7 (Fast)

Direct 8x 01 04 48 0p 0q 0r 0s FF pqrs: Focus Position*

Direct(VariableSpeed)

AutoFocus 8x 01 04 38 02 FF AF ON/OFF

ManualFocus 8x 01 04 38 03 FF

Auto/Manual 8x 01 04 38 10 FF

One Push Trigger 8x 01 04 18 01 FF

Infinity 8x 01 04 18 02 FF

CAM_AF_ASSIST** ON 8x 01 7E 01 44 02 FF

OFF 8x 01 7E 01 44 03 FF

CAM_F_NearLimit ON 8x 01 7E 01 41 02 FF

OFF 8x 01 7E 01 41 03 FF

CAM_WB Auto1 8x 01 04 35 00 FF

Auto2 8x 01 04 35 04 FF

Indoor 8x 01 04 35 01 FF

Outdoor 8x 01 04 35 02 FF

One Push 8x 01 04 35 03 FF

Manual 8x 01 04 35 05 FF

One Push Trigger 8x 01 04 10 05 FF

CAM_WB_RShift Direct 8x 01 7E 01 45 00 0q FF q: 0 - E

Up 8x 01 7E 01 45 01 02 FF

Down 8x 01 7E 01 45 01 03 FF

CAM_WB_BShift Direct 8x 01 7E 01 46 00 0q FF q: 0 - E

Up 8x 01 7E 01 46 01 02 FF

Down 8x 01 7E 01 46 01 03 FF

* See the section under VISCA Command Setting Values. ** Available only when focus mode is set to AUTO.

8x 01 7E 01 4A 0V 0p 0q 0r 0s FF

8x 01 7E 01 4B 0V 0p 0q 0r 0s FF

V: 0 - 7 (Speed), pqrs: Zoom Position*

V: 0 - 7 (Speed), pqrs: Focus Position*

Page 10

BRC-Z700 Command List (2/5)

Command Set Command Command Packet Comments

CAM_RGain Reset 8x 01 04 03 00 FF

Up 8x 01 04 03 02 FF

Down 8x 01 04 03 03 FF

Direct 8x 01 04 43 00 00 0p 0q FF pq: R Gain (00 - FF)

CAM_BGain Reset 8x 01 04 04 00 FF

Up 8x 01 04 04 02 FF

Down 8x 01 04 04 03 FF

Direct 8x 01 04 44 00 00 0p 0q FF pq: B Gain (00 - FF)

CAM_COLOR_GAIN Up 8x 01 04 09 02 FF

Down 8x 01 04 09 03 FF

Reset 8x 01 04 09 00 FF

Direct 8x 01 04 49 00 00 00 0p FF p: 0 - E

CAM_WB_Sens Low 8x 01 04 56 01 FF

Middle 8x 01 04 56 02 FF

High 8x 01 04 56 03 FF

CAN_ColorMatrix On 8x 01 7E 01 3D 02 FF

Off 8x 01 7E 01 3D 03 FF

R.ENHANCE 8x 01 7E 01 47 0p 0q FF pq: 00 - 14

G.ENHANCE 8x 01 7E 01 48 0p 0q FF pq: 00 - 14

B.ENHANCE 8x 01 7E 01 49 0p 0q FF pq: 00 - 14

YL.ENHANCE 8x 01 7E 01 50 0p 0q FF pq: 00 - 14

CY.ENHANCE 8x 01 7E 01 51 0p 0q FF pq: 00 - 14

MG.ENHANCE 8x 01 7E 01 52 0p 0q FF pq: 00 - 14

CAM_AE Full Auto 8x 01 04 39 00 FF

Manual 8x 01 04 39 03 FF

Shutter Priority 8x 01 04 39 0A FF

Iris Priority 8x 01 04 39 0B FF

Gain Priority 8x 01 04 39 0E FF

CAM_AE_Speed Low 8x 01 04 5D 01 FF

Middle 8x 01 04 5D 02 FF

High 8x 01 04 5D 03 FF

CAM_AGC_LIMIT Direct 8x 01 04 2C 0p FF p: Gain Limit*

CAM_IRIS_LIMIT Direct 8x 01 04 2B 0p FF p: Iris Limit*

CAM_Shutter Reset 8x 01 04 0A 00 FF

Up 8x 01 04 0A 02 FF Shutter setting (1/60sec - 1/10000sec [59.94i])

Down 8x 01 04 0A 03 FF

Direct 8x 01 04 4A 00 00 0p 0q FF pq: Shutter Speed Setting*

CAM_Iris Reset 8x 01 04 0B 00 FF

Up 8x 01 04 0B 02 FF

Down 8x 01 04 0B 03 FF

Direct 8x 01 04 4B 00 00 0p 0q FF pq: Iris Value Setting*

CAM_Gain Reset 8x 01 04 0C 00 FF

Up 8x 01 04 0C 02 FF

Down 8x 01 04 0C 03 FF

Direct 8x 01 04 4C 00 00 0p 0q FF pq: Gain Level Setting*

CAM_ExpComp On 8x 01 04 3E 02 FF

Off 8x 01 04 3E 03 FF

Reset 8x 01 04 0E 00 FF

Up 8x 01 04 0E 02 FF

Down 8x 01 04 0E 03 FF

Direct 8x 01 04 4E 00 00 00 0p FF p: ExpComp Level Setting*

* See the section under VISCA Command Setting Values.

(1/50sec - 1/10000sec [50i])

Page 11

BRC-Z700 Command List (3/5)

Command Set Command Command Packet Comments

CAM_BackLight On 8x 01 04 33 02 FF

Off 8x 01 04 33 03 FF

CAM_SpotLight On 8x 01 04 3A 02 FF

Off 8x 01 04 3A 03 FF

Flicker Reduction On 8x 01 04 32 02 FF

Off 8x 01 04 32 03 FF

CAM_Aperture Reset 8x 01 04 02 00 FF

Up 8x 01 04 02 02 FF

Down 8x 01 04 02 03 FF

Direct 8x 01 04 42 00 00 00 0p FF p: 0 - F (h)

CAM_ColorDetail COLOR DETAIL 8x 01 7E 01 4C 0p FF p: 0 = NARROW, 1 = STD, 2 = WIDE, 3 = OFF,

4 = CHECK

COLOR DETAIL PHASE 8x 01 7E 01 4D 0p 0q FF pq: 00 - 47

CAM_Gamma Normal 8x 01 04 5B 00 FF

Cinema 8x 01 04 5B 01 FF

CAM_PictureEffect Off 8x 01 04 63 00 FF

B&W 8x 01 04 63 04 FF

CAM_Steady_Shot On 8x 01 04 34 02 FF

Off 8x 01 04 34 03 FF

SOFT 8x 01 04 54 01 FF

STANDARD 8x 01 04 54 02 FF

HARD 8x 01 04 54 03 FF

CAM_H_Phase Up 8x 01 7E 01 3E 00 02 FF

Down 8x 01 7E 01 3E 00 03 FF

CAM_Memory Reset 8x 01 04 3F 00 0p FF p: Memory number (0 - F)

Set 8x 01 04 3F 01 0p FF p: Memory number (0 - F)

Recall 8x 01 04 3F 02 0p FF p: Memory number (0 - F)

CAM_Menu Off 8x 01 06 06 03 FF

CAM_Title Title Set 1 8x 01 7E 01 10 uu vv ww

00 00 00 00 00 00 00 FF

Title Set 2 8x 01 7E 01 11 aa bb cc dd

ee ff gg hh ii jj FF

Title Set 3 8x 01 7E 01 12 kk ll mm nn

oo pp qq rr ss tt FF

Title Clear 8x 01 7E 01 13 00 FF

Title On 8x 01 7E 01 13 02 FF

Title Off 8x 01 7E 01 13 03 FF

CAM_Preset_title Title Set 1 8x 01 7E 01 14 uu vv ww

0! 00 00 00 00 00 00 00 FF

Title Set 2 8x 01 7E 01 15 0! aa bb cc dd

ee ff gg hh ii jj FF

Title Set 3 8x 01 7E 01 16 0! kk ll mm

nn oo pp qq rr ss tt FF

Title Clear 8x 01 7E 01 17 0! 00 FF (!: position No (0 - F))

Title On 8x 01 7E 01 17 00 02 FF

Title Off 8x 01 7E 01 17 00 03 FF

CAM_IDWrite 8x 01 04 22 0p 0q 0r 0s FF pqrs: CameraID (0000 - FFFF)

IR_Receive On 8x 01 06 08 02 FF

Off 8x 01 06 08 03 FF

On/Off 8x 01 06 08 10 FF

(uu: Hposition [00 - 18 (h)], vv: Vposition [00 0A (h)], ww: Blink)

aa - jj: First 10 Words (ASCII CODE 20h to 7Eh)

kk - tt: Last 10 Words (ASCII CODE 20h to 7Eh)

(uu: Hposition, vv: Vposition, ww: Blink, !: preset No 0 - F)

aa - jj: First 10 Words (ASCII CODE 20h to 7Eh), !: Position No. (0 - F)

kk - tt: Last 10 Words (ASCII CODE 20h to 7Eh), !: Position No. (0 - F)

Page 12

BRC-Z700 Command List (4/5)

Command Set Command Command Packet Comments

Pan-tiltDrive Up

Down

Left

Right

UpLeft

UpRight

DownLeft

DownRight

Stop

AbsolutePosition 8x 01 06 02 VV 00 0Y 0Y 0Y

RelativePosition 8x 01 06 03 VV 00 0Y 0Y 0Y

Home 8x 01 06 04 FF

Reset 8x 01 06 05 FF

Pan-tiltLimitSet LimitSet 8x 01 06 07 00 0W 0Y 0Y 0Y

LimitClear 8x 01 06 07 01 0W 07 0F 0F

RAMP_CURVE MODE1 8x 01 06 31 01 FF

MODE2 8x 01 06 31 02 FF

MODE3 8x 01 06 31 03 FF

D-SUB 15Pin OUTPUT

D-SUB 15Pin SYNC 3-STATE 8x 01 7E 01 1A 00 00 FF

EXT_SYNC Synchronous mode

CAM_ImgFlip On 8x 01 04 66 02 FF

CAM_PanReverse On 8x 01 7E 01 06 00 01 FF

CAM_TiltReverse On 8x 01 7E 01 09 00 01 FF

Cmd_Tally On 8x 01 7E 01 0A 00 02 FF When Power is on, return to off.

Cmd_PT_M_Speed Preset PT Speed 8x 01 7E 01 0B 0p qq FF p: Memory number (0 - F), qq: Speed (1 - 18 h

Cmd_Disp_Info On 8x 01 7E 01 18 02 FF

Cmd_dzm_chg E-Zoom Limit 81 01 7E 01 19 0p FF p: 0=

Cmd_Color_Bar On 81 01 04 7D 02 FF When Power is on, return to off.

CAM_SD_VideoOutput_ PictureSize

* See the section under VISCA Command Setting Values.

Output 1 RGB 8x 01 7E 01 03 00 00 FF

Output 1 YPbPr 8x 01 7E 01 03 00 01 FF

RGB SYNC OFF 8x 01 7E 01 07 00 00 FF

RGB SYNC RGB 8x 01 7E 01 07 00 02 FF

VD 8x 01 7E 01 1A 00 01 FF

STD (HD) 8x 01 7E 01 2C 00 FF

STD (SD) 8x 01 7E 01 2C 03 FF

HD1 8x 01 7E 01 2C 01 FF

SD1 8x 01 7E 01 2C 02 FF

Off 8x 01 04 66 03 FF

Off 8x 01 7E 01 06 00 00 FF

Off 8x 01 7E 01 09 00 00 FF

Off 8x 01 7E 01 0A 00 03 FF

Off 8x 01 7E 01 18 03 FF

Off 81 01 04 7D 03 FF

4:3 [Squeeze] 8x 01 7E 01 3C 00 FF

16:9 [Letter] 8x 01 7E 01 3C 01 FF

4:3 [Crop] 8x 01 7E 01 3C 02 FF

8x 01 06 01 VV WW 03 01 FF

8x 01 06 01 VV WW 03 02 FF

8x 01 06 01 VV WW 01 03 FF

8x 01 06 01 VV WW 02 03 FF

8x 01 06 01 VV WW 01 01 FF

8x 01 06 01 VV WW 02 01 FF

8x 01 06 01 VV WW 01 02 FF

8x 01 06 01 VV WW 02 02 FF

8x 01 06 01 VV WW 03 03 FF

0Y 0Y 0Z 0Z 0Z 0Z FF

0F 0F 07 0F 0F 0F FF

Pan Speed VV (01: Slow to 18h: Fast) Tilt Speed WW (01: Slow to 18h: Fast)

Speed VV (01: Slow to 18h: Fast) YYYYY: Pan Position* ZZZZ: Tilt Position*

W: 1=UpRight 0=DownLeft YYYYY: PanLimit Position* ZZZZ: TiltLimit Position*

W: 1=UpRight 0=DownLeft

(fast))

×1.0, 1= ×1.5, 2= ×2.0, 3= ×4.0

Page 13

BRC-Z700 Command List (5/5)

Command Set Command Command Packet Comments

CAM_SD_VideoOutput_ Setup*

* Available only for 59.94i output signal.

Command Set Command Command Packet Comments

CARD_SDSDI_PictureSize

FOR HFBK-XG1 Only

FOR HFBK-SD1 Only

FOR HFBK-HD1 Only

FOR HFBK-TS1 Only

ON (7.5IRE) 8x 01 7E 01 3F 00 FF

OFF (0IRE) 8x 01 7E 01 3F 01 FF

4:3 [Squeeze] 8x 01 7E 01 43 00 00 FF

16:9 [Letter] 8x 01 7E 01 43 00 01 FF

4:3 [Crop] 8x 01 7E 01 43 00 02 FF

Command Set Command Command Packet Comments

CARD_Picture_size VGA [Crop] 8x 01 7E 01 1B 0p 00 FF

WXGA 8x 01 7E 01 1B 0p 01 FF

XGA [Crop] 8x 01 7E 01 1B 0p 02 FF

VGA [Letter] 8x 01 7E 01 1B 0p 04 FF

XGA [Letter] 8x 01 7E 01 1B 0p 06 FF

CARD_Sync_G Off 8x 01 7E 01 1C 0p 00 FF

On 8x 01 7E 01 1C 0p 01 FF

CARD_VD_Logic (only when WXGA is selected)

CARD_DOWN_OUTSEL1

CARD_DOWN_OUTSEL2

CARD_Picture_size 4:3 [Squeeze] 8x 01 7E 01 27 0p 00 FF

CARD_7.5IRE_Setup*

CARD_Analog_outsel

CARD_Analog_RGB_SYNC

CARD_SYNC_SEL

Audio Delay setting q: 0 - A (step) 8x 01 7E 01 2B 0p 0q FF

NEG 8x 01 7E 01 1D 0p 01 FF

POS 8x 01 7E 01 1D 0p 00 FF

RGB 8x 01 7E 01 24 0p 00 FF

YPbPr 8x 01 7E 01 24 0p 01 FF

Y/C 8x 01 7E 01 25 0p 00 FF

Composite 8x 01 7E 01 25 0p 01 FF

SYNC G 8x 01 7E 01 26 0p 01 FF

SYNC OFF 8x 01 7E 01 26 0p 02 FF

SYNC RGB 8x 01 7E 01 26 0p 03 FF

16:9 [Letter] 8x 01 7E 01 27 0p 01 FF

4:3 [Crop] 8x 01 7E 01 27 0p 02 FF

ON (7.5IRE) 8x 01 7E 01 3B 0p 00 FF

OFF (0IRE) 8x 01 7E 01 3B 0p 01 FF

RGB 8x 01 7E 01 28 0p 00 FF

YPbPr 8x 01 7E 01 28 0p 01 FF

RGB SYNC OFF 8x 01 7E 01 29 0p 00 FF

RGB SYNC ON (RGB) 8x 01 7E 01 29 0p 01 FF

VD 8x 01 7E 01 2A 0p 00 FF

3-STATE 8x 01 7E 01 2A 0p 01 FF

p: 1 =BRU-H700 CARD SLOT No.1

2 =BRU-H700 CARD SLOT No.2

* Available only for 59.94i output signal.

Page 14

BRC-Z700 Inquiry Command List (1/4)

Inquiry Command Command Packet Inquiry Packet Comments

CAM_PowerInq 8x 09 04 00 FF y0 50 02 FF On

y0 50 03 FF Off (Standby)

CAM_ZoomPosInq 8x 09 04 47 FF y0 50 0p 0q 0r 0s FF pqrs: Zoom Position

CAM_FocusModeInq 8x 09 04 38 FF y0 50 02 FF Auto Focus

y0 50 03 FF Manual Focus

CAM_FocusNearLimitInq 8x 09 7E 01 41 FF y0 50 02 FF On

y0 50 03 FF Off

CAM_FocusPosInq 8x 09 04 48 FF y0 50 0p 0q 0r 0s FF pqrs: Focus Position

CAM_WBModeInq 8x 09 04 35 FF y0 50 00 FF Auto1

y0 50 01 FF Indoor

y0 50 02 FF Outdoor

y0 50 03 FF One Push WB

y0 50 04 FF Auto2

y0 50 05 FF Manual

CAM_RGainInq 8x 09 04 43 FF y0 50 00 00 0p 0q FF pq: R Gain

CAM_BGainInq 8x 09 04 44 FF y0 50 00 00 0p 0q FF pq: B Gain

CAM_ColorGainInq 8x 09 04 49 FF y0 50 00 00 00 0p FF p: ColorGain (0 - E)

CAM_WBSensInq 8x 09 04 56 FF y0 50 01 FF Low

y0 50 02 FF Middle

y0 50 03 FF High

CAM_ColorMatrixInq 8x 09 7E 01 3D FF y0 50 02 FF On

y0 50 03 FF Off

WB R.SHIFT 8x 09 7E 01 45 FF y0 50 00 00 0p 0q FF

WB B.SHIFT 8x 09 7E 01 46 FF y0 50 00 00 0p 0q FF

R.ENHANCE 8x 09 7E 01 47 FF y0 50 00 00 0p 0q FF

G.ENHANCE 8x 09 7E 01 48 FF y0 50 00 00 0p 0q FF

B.ENHANCE 8x 09 7E 01 49 FF y0 50 00 00 0p 0q FF

YL.ENHANCE 8x 09 7E 01 50 FF y0 50 00 00 0p 0q FF

CY.ENHANCE 8x 09 7E 01 51 FF y0 50 00 00 0p 0q FF

MG.ENHANCE 8x 09 7E 01 52 FF y0 50 00 00 0p 0q FF

CAM_AEModeInq 8x 09 04 39 FF y0 50 00 FF Full Auto

y0 50 03 FF Manual

y0 50 0A FF Shutter Priority

y0 50 0B FF Iris Priority

y0 50 0E FF Gain Priority

CAM_AE Speed Inq 8x 09 04 5D FF y0 50 01 FF Low

y0 50 02 FF Middle

y0 50 03 FF High

CAM_AGC Limit Inq 8x 09 04 2C FF y0 50 00 FF 0dB

y0 50 01 FF 6dB

y0 50 02 FF 12dB

y0 50 03 FF 18dB

y0 50 04 FF Off

CAM_IrisLimitInq 8x 09 04 2B FF y0 50 00 FF F11

y0 50 01 FF F6.8

y0 50 02 FF F4.0

y0 50 03 FF F3.4

CAM_ShutterPosInq 8x 09 04 4A FF y0 50 00 00 0p 0q FF pq: Shutter Position*

CAM_IrisPosInq 8x 09 04 4B FF y0 50 00 00 0p 0q FF pq: Iris Position*

CAM_GainPosInq 8x 09 04 4C FF y0 50 00 00 0p 0q FF pq: Gain Position*

* See the section under VISCA Command Setting Values.

Page 15

BRC-Z700 Inquiry Command List (2/4)

Inquiry Command Command Packet Inquiry Packet Comments

CAM_ExpCompModeInq 8x 09 04 3E FF y0 50 02 FF On

y0 50 03 FF Off

CAM_ExpCompPosInq 8x 09 04 4E FF y0 50 00 00 0p 0q FF pq: ExpComp Position*

CAM_BackLightModeInq 8x 09 04 33 FF y0 50 02 FF On

y0 50 03 FF Off

CAM_SpotLightModeInq 8x 09 04 3A FF y0 50 02 FF On

y0 50 03 FF Off

CAM_ApertureInq 8x 09 04 42 FF y0 50 00 00 0p 0q FF pq: Aperture Gain (0 - F)

CAM_ColorDetail ModeInq 8x 09 7E 01 4C FF y0 50 0p FF p: 0 - 3

CAM_ColorDetail PhaseInq 8x 09 7E 01 4D FF y0 50 00 00 0p 0q FF

CAM_PictureEffectModeInq 8x 09 04 63 FF y0 50 00 FF Off

y0 50 04 FF B & W

CAM_GammaTypeInq 8x 09 04 5B FF y0 50 00 FF Normal

y0 50 01 FF Cinema

Flicker_ReductionInq 8x 09 04 32 FF y0 50 02 FF On

y0 50 03 FF Off

CAM_SteadyModeInq 8x 09 04 34 FF y0 50 02 FF On

y0 50 03 FF Off

CAM_SteadyTypeInq 8x 09 04 54 FF y0 50 01 FF SOFT

y0 50 02 FF STANDARD

y0 50 03 FF HARD

CAM_EXTSYNC_HPhaseInq 8x 09 7E 01 3E FF y0 50 0p 0q FF

CAM_MemoryInq 8x 09 04 3F FF y0 50 pp FF pp: Memory number last operated*

CAM_MENUInq 8x 09 06 06 FF y0 50 02 FF On

y0 50 03 FF Off

CAM_IDInq 8x 09 04 22 FF y0 50 0p 0q 0r 0s FF pqrs: Camera ID (000 - FFFF)

CAM_VersionInq 8x 09 00 02 FF y0 50 00 01

mn pq rs tu vw FF

CAM_TitleModeInq 8x 09 7E 01 13 FF y0 50 02 FF On

y0 50 03 FF Off

CAM_PresetTitleModeInq 8x 09 7E 01 17 FF y0 50 02 FF On

y0 50 03 FF Off

CAM_ReceiveInq 8x 09 06 08 FF y0 50 02 FF On

y0 50 03 FF Off

D-SUB 15Pin OutputInq 8x 09 7E 01 03 FF y0 50 0p FF p: 0=RGB, 1=YPbPr

D-SUB 15Pin RGB_SYNCInq 8x 09 7E 01 07 FF y0 50 0p FF p: 0=OFF, 2=RGB

D-SUB 15Pin SYNC OUTInq 8x 09 7E 01 1A FF y0 50 00 FF 3-STATE

y0 50 01 FF VD

CAM_ImgFlipInq 8x 09 04 66 FF y0 50 02 FF On

y0 50 03 FF Off

CAM_DataMixInq 8x 09 7E 01 05 FF y0 50 02 FF On

y0 50 03 FF Off

CAM_PanReverseInq 8x 09 7E 01 06 FF y0 50 01 FF On

y0 50 00 FF Off

CAM_TiltReverseInq 8x 09 7E 01 09 FF y0 50 01 FF On

y0 50 00 FF Off

PanTilt_Status 8x 09 06 10 FF y0 50 pq rs FF pqrs: PanTilt Status*

mnpq: Model Code (05xx) rstu: ROM version vw: Socket Number (02)

* See the section under VISCA Command Setting Values.

Page 16

BRC-Z700 Inquiry Command List (3/4)

Inquiry Command Command Packet Inquiry Packet Comments

PanTilt_Max_Speed 8x 09 06 11 FF y0 50 pq rs FF pq: Pan Max Speed, rs: Tilt Max Speed

PanTilt_Position 8x 09 06 12 FF

Tally 8x 09 7E 01 0A FF y0 50 02 FF On

PanTilt_Memory_Speed 8x 09 7E 01 0B 0p FF y0 50 qq FF p: Preset No. 0 - F, qq: Speed 1 - 18 (h)

Pantilt_RampCurveInq 8x 09 06 31 FF y0 50 01 FF MODE1

CAM_Dzoom_LimitInq 8x 09 7E 01 1E FF y0 50 00 FF Limit

Block_inq Refer to Block Inquiry Command List.

CAM_50i60i_inq 8x 09 7E 01 31 FF y0 50 00 FF 50i

Cam_Card_StatusInq 8x 09 7E 01 0E FF y0 50 0p FF

CAM_EXTSYNC_SynchronousModeInq

CAM_Color_barInq 8x 09 04 7D FF y0 50 02 FF ON

CAM_SD_VideoOutput_PicSizeInq

CAM_SD_VideoOutput_SetupInq**

8x 09 7E 01 2C FF y0 50 00 FF STD (HD)

8x 09 7E 01 3C FF y0 50 00 FF 4:3 [Squeeze]

8x 09 7E 01 3F FF y0 50 00 FF ON (7.5IRE)

y0 50 0p 0q 0r 0s 0t 0u 0v 0w 0x FF

y0 50 03 FF Off

y0 50 02 FF MODE2

y0 50 03 FF MODE3

pqrst: Pan Position* uvwx: Tilt Position*

×1.0 (D-Zoom off)

y0 50 01 FF Limit ×1.5 y0 50 02 FF Limit ×2.0

y0 50 03 FF Limit

y0 50 01 FF 59.94i

y0 50 01 FF HD1

y0 50 02 FF SDI

y0 50 03 FF STD (SD)

y0 50 03 FF OFF

y0 50 01 FF 16:9 [Letter]

y0 50 02 FF 4:3 [Crop]

y0 50 01 FF OFF (0IRE)

×4.0

p: Information on the optional card inserted in the interface card slot of the BRC-Z700 1=BRBK-MF1 8=BRBK-HSD1 (HD) 9= BRBK-HSD1 (SD) F=No card

* See the section under VISCA Command Setting Values. ** Available only for 59.94 output signal.

Inquiry Command Command Packet Inquiry Packet Comments

CARD_SD-SDI_PictureSizeInq

Inquiry Command Command Packet Inquiry Packet Comments

FOR HFBK-XG1 Only

CARD_Picture_SizeInq 8x 09 7E 01 1B 0p FF y0 50 00 FF VGA [Crop]

CARD_Sync_GInq 8x 09 7E 01 1C 0p FF y0 50 00 FF SYNC OFF

CARD_VD_LogicInq 8x 09 7E 01 1D 0p FF y0 50 01 FF NEG

8x 09 7E 01 43 00 FF y0 50 00 FF 4:3 [Squeeze]

y0 50 01 FF 16:9 [Letter]

y0 50 02 FF 4:3 [Crop]

y0 50 01 FF WXGA

y0 50 02 FF XGA [Crop]

y0 50 04 FF VGA [Letter]

y0 50 06 FF XGA [Letter]

y0 50 01 FF SYNC ON (G)

y0 50 00 FF POS

p: 1= BRU-H700 CARD

SLOT No.1

2= BRU-H700 CARD

SLOT No.2

Page 17

BRC-Z700 Inquiry Command List (4/4)

Inquiry Command Command Packet Inquiry Packet Comments

FOR HFBK-SD1 Only

FOR HFBK-HD1 Only

FOR HFBK-TS1 Only

* Available only for 59.94 output signal.

CARD_D-SUB_OUT1Inq 8x 09 7E 01 24 0p FF y0 50 00 FF RGB

CARD_D-SUB_OUT2Inq 8x 09 7E 01 25 0p FF y0 50 00 FF Y/C

CARD_RGBSYNC Inq 8x 09 7E 01 26 0p FF y0 50 01 FF SYNC ON (G)

CARD_Picture_SizeInq 8x 09 7E 01 27 0p FF y0 50 00 FF 4:3 [Squeeze]

CARD_7.5IRE_SetupInq* 8x 09 7E 01 3B 0p FF y0 50 00 FF ON (7.5IRE)

CARD_Analog_OUTSEL_Inq

CARD_Analog_RGB_SYNC Inq

CARD_SYNC_SEL Inq 8x 09 7E 01 2A 0p FF y0 50 00 FF VD

Audio Delay 8x 09 7E 01 2B 0p FF y0 50 0q FF q: 0 (off) -

8x 09 7E 01 28 0p FF y0 50 00 FF RGB

8x 09 7E 01 29 0p FF y0 50 00 FF RGB SYNC

y0 50 01 FF YCbCr

y0 50 01 FF VBS

y0 50 02 FF SYNC OFF

y0 50 03 FF SYNC RGB

y0 50 01 FF 16:9 [Letter]

y0 50 02 FF 4:3 [Crop]

y0 50 01 FF OFF (0IRE)

y0 50 01 FF YPbPr

OFF

y0 50 01 FF RGB SYNC

y0 50 01 FF 3-STATE

A (10 step)

p: 1= BRU-H700 CARD

SLOT No.1

2= BRU-H700 CARD

SLOT No.2

Page 18

BRC-Z700 Block Inquiry Command List

Lens control system inquiry commands…..Command Packet 8x 09 7E 7E 00 FF

Byte Bit Comments

Destination Address

Source Address

0 Completion Message(50h)

Zoom Position (HH)

Zoom Position (HL)

Zoom Position (LH)

Zoom Position (LL)

Byte Bit Comments

Focus Position (HH)

Focus Position (HL)

Focus Position (LH)

Focus Position (LL)

Byte Bit Comments

5 D-Zoom Mode

(1: Separate, 0: Combine)

3 Focus Near Limit

(1: On, 0: Off)

2 AF Assist (1: On, 0: Off)

1 D-Zoom (1: On, 0: Off)

0 Focus (1: Auto,

0: Manual)

2 Camera Memory Recall

(1: Executing, 0: Stop)

1 Focus Command

(1: Executing, 0: Stop)

0Zoom Command

(1: Executing, 0: Stop)

7 1 Terminator (FFh)

Page 19

Camera control system inquiry commands (1/2)…..Command Packet 8x 09 7E 7E 01 FF

Byte Bit Comments

Destination Address

Source Address

0 Completion Message(50h)

WB R-Gain (H)

WB R-Gain (L)

WB B-Gain (H)

WB B-Gain (L)

Byte Bit Comments

5AWB Sens

(1: Low, 2: Mid, 3: High)

2WB Mode

(0: Auto1, 1: Indoor,

2: Outdoor, 3: OnePush,

4: Auto2, 5: Manual)

3 Spot Light (1: On, 0: Off)

Back Light (1: On, 0: Off)

1 Exposure Comp.

(1: On, 0: Off)

Hyper Gain (1: On, 0: Off)

Manual Shutter Position

Detail

Exposure Mode

(0: Auto, 1: Manual,

A: Shutter Pri, B: Iris,

0E: Gain Pri)

Manual Iris Position

Byte Bit Comments

Manual Gain Position

0IMG-FLIP

Exposure Comp. Position

7 1 Terminator (FFh)

Page 20

Camera control system inquiry commands (2/2)…..Command Packet 8x 09 7E 7E 02 FF

Byte Bit Comments

Destination Address

1 (1: 59.94i, 0: 50i)

0 Power On (1: On, 0: Off)

4 Steady Shot (1: On,

3 indefinite

Source Address

0 Completion Message(50h)

YL.ENHANCE

Color Gain

0: Off)

Flicker Cancel (1: On, 0: Off)

0B & W (1: On, 0: Off)

Byte Bit Comments

3 Steady Shot Type

(1: Soft, 2: Std, 3: Hard)

4COLOR MATRIX

1ND Select

(0: Off, 1: Filter1,

2: Filter2)

Gamma Mode

(0: Normal, 1: Cinema)

CY.ENHANCE

MG.ENHANCE

MODE

AE Speed

(1: Low, 2: Middle,

3: High)

AGC Limit

(0: 0 dB, 1: 6 dB,

02: 12 dB, 3: 18 dB)

Byte Bit Comments

1 Iris Limit

1 D-Zoom Limit

7 1 Terminator (FFh)

(0: F11, 1: F6.8, 2: F4.0, 3: F3.4)

×1.0, 1: ×1.5,

(0:

×2.0, 3: ×4.0)

Page 21

Other enlargement inquiry commands (1/2) .......... Command Packet 8x 09 7E 7E 03 FF

Byte Bit Comments

Destination Address

Source Address

0 Completion Message(50h)

D-Zoom Position (H)

D-Zoom Position (L)

WB R.SHIFT

WB B.SHIFT

Byte Bit Comments

R.ENHANCE

G.ENHANCE

B.ENHANCE

COLOR DETAIL MODE

Shutter Pri Position

Iris Pri Position

Byte Bit Comments

7 1 Terminator (FFh)

Gain Pri Position

COLOR DETAIL

PHASE

Page 22

Other enlargement inquiry commands (2/2) .......... Command Packet 8x 09 7E 7E 04 FF

Byte Bit Comments

Destination Address

Source Address

0 Completion Message(50h)

Current WB R-GAIN (H)

Current WB R-GAIN (L)

Current WB B-GAIN (H)

Current WB B-GAIN (L)

Byte Bit Comments

1 IRIS Pri Open F-number

0 MANUAL IRIS Open F-

prism temp (H)

prism temp (L)

IRIS Position Open F-number limit

limit

number limit

Shutter Current Position

Iris Current Position

Byte Bit Comments

Gain Current Position

7 1 Terminator (FFh)

Lens Fan rpm (H)

Lens Fan rpm (L)

Page 23

VISCA Command Setting Values

Exposure control

Iris Gain

Parameter

1C F1.6

1B F1.7

1A F1.8

19 F2.0

18 F2.2

17 F2.4

16 F2.6

15 F2.8

14 F3.1

13 F3.4

12 F3.7

11 F4.0

10 F4.4

0F F4.8

0E F5.2

0D F5.6

0C F6.2

0B F6.8

0A F7.3

09 F8.0

08 F8.7

07 F9.6

06 F10

05 F11

04 F12

03 F14

02 F15

01 F16

00 CLOSE

IRIS (F1.6)

F No.

Iris Limit

Parameter GAIN (dB)

1A HYPER

19 24

18 23

17 22

16 21

15 20

14 19

13 18

12 17

11 16

10 15

0F 14

0E 13

0D 12

0C 11

0B 10

0A 9

09 8

08 7

07 6

06 5

05 4

04 3

03 2

02 1

01 0

Parameter F No.

3F3.4

2F4.0

1F6.8

0F11

Page 24

Shutter Speed

SHUTTER

15 1/10000 1/10000

14 1/6000 1/6000

13 1/4000 1/3500

12 1/3000 1/2500

11 1/2000 1/1750

10 1/1500 1/1250

0F 1/1000 1/1000

0E 1/725 1/600

0D 1/500 1/425

0C 1/350 1/300

0B 1/250 1/215

0A 1/180 1/150

09 1/125 1/120

08 1/100 1/100

07 1/90 1/75

06 1/60 1/50

59.94i 50i (sec) (sec)

Exposure Compensation

EXPOSURE

COMP.

0E +10.5 +7

0D +9 +6

0C +7.5 +5

0B +6 +4

0A +4.5 +3

09 +3 +2

08 +1.5 +1

07 0 0

06 –1.5 –1

05 –3 –2

04 –4.5 –3

03 –6 –4

02 –7.5 –5

01 –9 –6

00 –10.5 –7

Comp Value

(dB)

Display

Zoom Ratio and Zoom Position (for reference)

Optical Zoom

Position

DATA

0000 1982 ×2

24E2 ×3

2BC9

3099 ×5

343D ×6

3724 3988 ×8

3B8B ×9

3D43

3EBB ×11

4000 ×12

Digital Zoom

Position

DATA

4000 ×1

6A00 ×2

7800 7F00 ×4

Zoom Ratio

×20 Lens

×1

×4

×7

×10

Zoom Ratio

×20Lens

×3

Gain Limit

Parameter

4OFF

318

212

GAIN

(dB)

Page 25

Focus Ratio and Focus Position (for reference)

Focus Ratio Focus Distance

1000 Over Inf

2000 4 m

3000 1.8 m

4000 1.0 m

5000 65 cm

6000 30 cm

7000 20 cm

8000 13 cm

9000 7 cm

A000 4 cm

B000 2 cm

C000 1 cm

Pan/Tilt Position (for reference)

Pan

Angle (degrees)

0 00000 00000

10 00938 FF6C8

20 01270 FED90

30 01BA8 FE458

40 024E0 FDB20

50 02E18 FD1E8

60 03750 FC8B0

70 04088 FBF78

80 049C0 FB640

90 052F8 FAD08

100 05C30 FA3D0

110 06568 F9A98

120 06EA0 F9160

130 077D8 F8828

140 08110 F7EF0

150 08A48 F75B8

160 09380 F6C80

169 09BDE F6422

Left Right

YYYYY YYYYY

Tilt

Angle (degrees)

000000000

10 0938 F6C8

20 1270 ED90

30 1BA8 E458

40 24E0 –

50 2E18 –

60 3750 –

70 4088 –

80 49C0 –

90 52F8 –

Up Down

ZZZZ ZZZZ

Page 26

Pan/Tilt Status Code List

PQRS

0 – – – – – – – 0 – – – – – – 1 Panning reaches the end of the left. 0 – – – – – – – 0 – – – – – 1 – Panning reaches the end of the right.

– – – – – – – 0 – – – – 1 – – Tilting reaches the upper limit.

0 – – – – – – – 0 – – – 1 – – – Tilting reaches the lower limit. 0 – – – – – – – 0 – – – 1 1 1 1 Pan/tilt position cannot be detected.

– – – – – – – – – 0 0 – – – – Pan functions normally.

0 – – – – – – – – – 1 0 – – – – Pan mechanism is defective. 0 – – – – – 0 00 – – – – – – – Tilt functions normally.

– – – – – 1 00 – – – – – – – Tilt mechanism is defective.

0 – – – 0 1 – – 0 – – – – – – – Pan/Tilt operating 0 – – – 1 0 – – 0 – – – – – – – Pan/Tilt operations complete.

– 0 0 – – – – 0 – – – – – – – Not initialized

0 – 0 1 – – – – 0 – – – – – – – Initializing 0 – 1 0 – – – – 0 – – – – – – – Initialization completes.

– 1 1 – – – – 0 – – – – – – – Initialization failed.

( – : optional)

Page 27

Memory Function (Inquiry Commands)

Preset No.

last operated

– 00 While no Recall commands are used after the power

1 7F 00 (or =00 for Reset, Set and Recall commands)

201

302

403

504

605

706

807

908

10 09

11 0A

12 0B

13 0C

14 0D

15 0E

16 0F

pp: Memory number

last operated

Comments

has been tuned on

Page 28

Revision History

Version Item Description

1.00 New edition

Vaddio BRC-Z700 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Overview of VISCA

VISCA Communication Specifications

VISCA Device Setting Command

VISCA Command/ACK Protocol

VISCA Camera-Issued Messages

BRC-Z700 Commands

BRC-Z700 Command List (1/5)

BRC-Z700 Command List (2/5)

BRC-Z700 Command List (3/5)

BRC-Z700 Command List (4/5)

BRC-Z700 Command List (5/5)

BRC-Z700 Inquiry Command List (1/4)

BRC-Z700 Inquiry Command List (2/4)

BRC-Z700 Inquiry Command List (3/4)

BRC-Z700 Inquiry Command List (4/4)

BRC-Z700 Block Inquiry Command List

VISCA Command Setting Values

Pan/Tilt Status Code List

Memory Function (Inquiry Commands)

Revision History