Page 1
16 pc. Mini Die Grinder Kit
User Manual
RETAIN THIS MANUAL FOR FUTURE REFERENCE
PLEASE READ THIS MANUAL CAREFULLY BEFORE USE
Page 2
16 pc. Mini Die Grinder Kit
Table of Contents
Intended Use .................................................................................................................................................. 1
Safety Instructions ................................................................................................................................... 1
General Instructions ................................................................................................................................. 2
Initial Start-Up ............................................................................................................................................ 2
Required Air Quality/Air Supply .............................................................................................................. 2
Setting Values for Operation .................................................................................................................. 2
Compressed Air Supply .............................................................................................................................. 3
Decommissioning .......................................................................................................................................... 3
Technical Specifications ........................................................................................................................... 3
i
Page 3
16 pc. Mini Die Grinder Kit
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Intended Use
This axial grinder is a hand y, compressed air-powered device for the DIY and automotive/tr uck areas. It is
suitable for t he grinding and planning of solid surfaces.
Only use this machine according to its intended use! Any use extendi ng beyond this does not constitute
intended use. The user, not the manufacturer , is liable for resulting damages or injuries of any kind.
Our equipment is not intended for commerc ial or industrial use. If t his device is used in the context of
commercial or industrial use, the warranty is void.
When using tools, som e safety precautions must be observed to prevent inj uries and damages.
Therefore, read through this operating manual/safety instructions caref ully. Store them in a safe
place so that the information is available to you at al l times. If you should hand the appliance on to
other people, please give these operating/safety instructions to them as well. W e will not assume
any liabilities for accidents or damages which do arise due to failure to observe these safety
instructions.
Safety Instructions
Keep these operating instructions ready at hand. You can then read up on import ant information and
instructions, if necessary.
Never make use of a defect ive or non-functioning device. Contact an aut horised service centre or have the
device inspected by a qualified skilled technician.
Disconnect t he axial g rinder from the compressor before you exchange the acc essories or an attachment.
Disconnect t he axial g rinder when not using the compressor.
Always work with the neces sary levels of care.
Do not apply unnecessary force under any circumstances.
While grinding, be careful of flying s parks. Glowing parts that are blown upward can easily ignite flammable
materials and liquids .
Always wear appropriate protective clothing when performing all works/pr ojects with the axial grinder s uch
as protective gloves, work boots, protective goggles, dust masks, ear pr otectors, etc. Persons in the
immediate working e nvironment should take the same protective measures.
Only us e sui table grinding inserts.
Make sure that the air pressure’s connectio n is not set at too high a level. T ake into account the possible
impact of anything in the vicinity. Make sure t hat the workplace is well-lit.
Always disconnect the device from the compressed air supply before any repair or servic ing work.
Improper repairs can result in injuries.
Never exceed the permissible operating pressure. Excessive pressure can damage the device and can lead
to i njuries.
Keep pneumatic tools away from children. This device can lead to injuries if it is not used as intended.
Only connect t he device to the pneumatic air supply via a quick-action coupling so it can be quickly
disconnected in the event of danger.
1
Page 4
16 pc. Mini Die Grinder Kit
•
•
•
•
•
•
•
•
•
Ensure that your hair does not get caught in the rotat ing tool. Wear a hair net for your saf ety.
Wear close-fitting clothing. Wide, loose clothing c an get caught in the rotating t ool and can lead to injuries.
Keep your workplace clean and in good order. Untidi ness in the workplace incr eases the risk of accidents.
New grinding tools m ust be run-in by running it idle f or half a minute.
Never slow down the grinder by pressing on it. At low rotational speeds, the lateral pressure can dam age the
grinder.
General Instructions
The recommended working pressure level is 6.2 bar.
ATTENTION! A level of working pressure that is too low leads to reduced performance, a level of working
pressure that is too high shortens the service life.
Wipe the tool with a dr y clot h. Never clean it with w ater or solvents . Solvents damage the seals. Water leads
to corros ion.
Always store the axial grinder in a dry and clean place.
In case of improper use and lack of maintenance, the legal warranty is void.
Initial Start-Up
1. Fill three to four drops of pneumatic oil into the compressed air supply.
2. Screw the couplings and plugs that are included with the delivery into the compressed air supply and seal it
with Teflon tape.
3. Select the grips D that are suitable for t he grinder F. The shaft of grinder F must fit into the grips D.
4. First, turn the clamping nut E loosely onto the thread of the grips bearing.
5. Slide the grinder Fi n the grips D to a maximum dist ance of 1 cm and tig hte n the cla mping nut with a spanner.
Hold the spindle in plac e with a spanner. The clamping n ut must be tig htened to t he extent that the grinder is
held in place.
Required Air Quality/Air Supply
Air quality should be c leaned; air supply should be coated in oil via a maintenance unit with filter pressure
reducers and inline oiler.
Setting Values for Operation
Change the operating pressure (flow pressure) on the pressure reducer to 6.2 bar.
2
Page 5
16 pc. Mini Die Grinder Kit
•
•
Compressed Air Supply
We recommend the use of an oil-fog lubricator in the compressed air line. If oil-fog lubricators (attached) are
not used, three to five drops of pneumatic oil must be fed into the compressed-air supply of the devic e
before any time it is used. Subsequent lubric ation is needed after three operating hours at the latest. More
fr equently if the ambient air is dusty and t he tool is being used constantly.
The service life is shortened if a maintenanc e unit with a condensate drainage is not used. The humidity in
the compressed air would lead t o corrosion in the device.
Decommissioning
After use, it is absolutely necessary to disconnect the compressed air hose. Accidental activation can lead to
injuries
Technical Specifications
Model
Air Requirements
Recommended operating
pressure
Rotation Speed
Air Connection
Material
Grips
Intended Ambient
Temperature
Vibration
Sound Power Level when
Idle
LX-002
115 L/min
90 PSI
25,000 rpm
Standard 1/ 4" NPT
Aluminium
3/6 mm
10 - 50°C
2.44 m/sec2
80 dB (A)
3
Page 6
Some experts believe the incorrect or prolonged use of almost any
product could cause
serious inju
ry or de
a
th. F
or inf
orm
ation th
at
may reduce your risk of serious injury or death consult thepoints
below and additionally, the information available at
www.datastreamserver.com/safety
- Consult all docume ntation, packaging and
product labelling before use. Note that some
products feature online documentation which
should be printed and kept with the p roduct.
- Check product for loose / broken / damaged /
missing parts, wear or leaks (if applicable) before
each use. Never use a product with loose / b roken
/ damaged / missing pa rts, wear or leaks (if
applicable).
- Products must be inspected and serviced (if
applicable) by a qualified specialist every 6
months assuming average residential use by a
person of average weight and strength, ab ove
average technical aptitude, on a property
matching average metropolitan specification.
Intended use outside these guidelines could
indicate the product is not suitable for intended
use or may require more regular inspection or
servicing.
- Ensure all possible users of the p roduct have
completed an industry recognised training course
before being given access to the product.
- The product has been supplied by a general merchandise
retailer that may not be familiar with your specific applic ation or
your description of the applic ation. Be sure to attain third party
approval for your application from a qualified specialist before use
regardless of prior assurances by the retailer or its representatives.
- This product is not intended for use where fail-safe operation is
required. As with any product (take an au tomobile, aircraft,
computer or ball poi nt pen for example) there is always a small
chance of a technical issue that needs to be repaired or may
require replacement of the product or a part. If the possibility of
such failure and the associated time it takes to rectify could in any
situation inconvenience the user, business or employee or could
financially affect the user, business or employee then the product
is not suitable for your requirements. This p roduct is not for use
where incorrect operation or a failure of any kind, including but
not limited to a condition requiring product return, replacement,
service by a technician or replacement of parts could cause a
financial loss, loss of employee time or an in c
onvenience
requiring compensation.
- If this item has been purchased in error considering the points
above simply contact the retailer directly for details of their
returns policies if required.
Loading...